battery DACIA SUPERNOVA 2004 Owner's Manual

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 21
DIAG
NOSING-INTERPRETING THE DEFECTS
CIRCUIT OF COMMAND ACTUATOR RELAY
1. Circuit of command or short-circuit to the mass of the circuit to-
wards pin 39 of the calculator
2.
Short-circ uit a t 12V a long the c irc uit tow a rds p in 39 of the c a lc ula tor
4.
SUGGESTIONSConditions of breakdown detection by the calculator:
-tak e the contact and wait till dialogue with the tester is lost
-put th e contact and enter dialogue.
Condition of performing the diagnosing:
-defec t is present.
REMARK : This defect has priority and should be dealt with be-
fore the following ones.
Check the state of the battery and the connections to the mass.
Remedy if necessary.
Check the connecting and the state of the connector of 238 relay.
Change the connector if necessary.
Check the presence of +12V at the pole 1 of 238 relay.
Remedy the circuit to fuse S
1 in the engine compartment.
Check the coil of the 238 actuator relay.
Change relay if necessary.
Connect the 90-way terminal-tester instead of the calculator and check the insulation and
the continuity along the circuit:
pin 39 of calculator
♦ pole 2 of actu ato r r elay 2 38.
Remedy if necessary.
The proble m is not yet solved! Consequently, the injection calculator must be changed.
CAUTION! The destruction of the calculator has probably been caused by an electric shock.
The cause of the destruction must be found before mounting a new
calcul ator.
AFTER REPAIR Er
ase defects memorized by the computer.
Perform the steps under “Suggestions” to confirm the repair.
Remedy other possible defects.
DEFECT
PR ESENT
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 49
DIAGNOSING-CON
FORMITY TEST
Finally, the testing of the various states and parameters of the system will be done,
in the following situations:
A - With the stopped engine, and with contact set
B - With the hot engine, in idle mode, without consumers
C - During a route test.
LIST OF STA TES
Nr.
crt:Characteristics
1.
State: +After Contact to calculator
Parameter: Supply voltage of
injection calculator
Actuating relay command
Stat e: Connection for AC
Stat e: Configuration with anti-
st arter
Stat e: Connection with speed
translator
Stat e: Anti-starter
Acceleration pedal let free
Stat e: position of clapper when the
acceleration pedal is raised
Parameter: position of cla pper
Parameter : Memorized va lue for
t he position when the pedal is raised
Acceleration pedal slightly pushed
Stat e: position of clapper when ac-
cele ration pedal is raise d
Stat e: position of clapper when ac-
celerat i on pedal is comp letel y
pushed
A cceleration pe dal completely
pushed
Stat e: position of clapper when ac-
celerat i on pedal is comp letel y
pushed
Parameter: position of cla pper
Function
Battery
voltage
2.
Injection
calc ulator
configura-
tion
3. Anti-starter
4.
SUGGESTIONSA- With the stopped engine, and with contact se t
Visualizing and
Rema rks
Confirmed state
11.8V Confirmed state
if the car is
equipped with AC
Confirmed state
Confirmed state
Not confirmed
state
Confirmed state
0 Not confirmed
state
Not confirmed
state
Confirmed state
200 further problems
arise, refer to the
di agnosing of that
parameter
If further problems
arise, refer to the
di agnosing of those
states
If further problems
arise, refer to the
di agnosing of that
state
If further problems
arise, refer to the
di agnosing of those
parameters Diagnosis
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 51
DIAGNOSING-CON
FORMITY TEST
SUGGESTIONS B - Wi
th the hot engine, in idle mode, wit hout consumers
Battery voltage
LIST OF STÃTES
State: +After Contact to calc u-
lator
Parameter: Supply voltage of
calc ulator
If the parameter: Supply volt-
age of calc ulator
Th en the parameter: Engine
rotation ratio Confirmed state

13V X<12.7
750 rot/min If further prob-
l
ems arise, refer
to the diagnosing
of that param-
eter
Petrol pump com-
m and
State: Co mmand of actuators’
relay
Confi rmed state
Confi rmed state
Stat e: Petrol pump relay com-
m and
Co mmand of ac-
tuat ors
If furthe r prob-
l ems arise, refer
to the diagnos-
ing of the rota-
tion signal infor-
mation defectConfi rmed stateStat e: Ro tation signal
Ro tation signal
If further
proble ms arise,
refer to the
“Diagnosing Conditions”
Confi rmed stateSt ate: Recognition of the 1
cylinder
Recognition of the
1 cylinder
1.
2.
3.
4.
5. Heating of oxygen
probe Stat
e: Heating of oxygen
probe
Confi rmed state
Cl apper potenti-
ometer Stat
e: Pos ition of clapper of
acceleration pedal: free (raise d)Confi rmed stateIf further
problems arise,
refer to the
di agnosing of
that parameter
Stat e: Idle mode adjustment
Parameter: engine rotation
Parameter: To lerance of idle
m ode regimen
Parameter: Idle mode RCO
Parameter: Idle mode RCO
adapta tion.Confi rmed state
725 < X < 7 75 rot/min
-25 < X < +25 ro t/min
5 % < X < 12 %
-3 % < X < 7 % If furthe
r prob-
l ems arise, refer
to the diagnos-
ing of that state
Idle mode adjust-
m
ent
6.
7.
8.
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 59
STATEAIR CONDITIONING AC COMPRESSOR REQUIREMENT
SUGGESTIONSNo defect should be present or memorized
The compressor
clutch do es n ot
couple Check the insulation and continuity along the circuit towards pin 10
injection calculator.
Remedy if necessary.
If
the incident persists, refer to the diagnosing of he air-conditioning.
AFTER REPAIRPerform again the conformity test
CALCULATOR POWER VOLTAGE
PA R AMETER
No defect should be present or memorized.
No consumer should be turned on.
SUGGESTIONS
The contac
t is set
If the voltage < the minimal voltage, then the battery may be flat.
Check the charging circuit, in order to detect the cause of the problem.
If the voltage > the maximal voltage, then it is possible that the
battery may be overcharged.
Check the charging voltage to be correct, with and without consumers.
In idle mode
If the vo ltage < the minimal voltage, then the charging voltage is too
small.
Check the charging circuit, in order to detect the cause of the problem.
If th e voltage > the maximal voltage, then the charge of the battery is
too high.
The vo ltage regulator is faulty.
Remedy this problem, and then check the level of the electrolyte in the
ba ttery.
DIAG NOSING-INTERPRETING THE STATES
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 60
DIAG
NOSING-INTERPRETING THE STATES
Remark:
The testing of the battery and the charging circuit can be done with “TECHNIC CLIP”
an d does not require disconnecting the battery, so it allow the conservation of the calculator
memory.
AFTER REPAIRPerform again the conformity test.
PA RAM ETER
CLAPPER POSITION
MEMORIZED VALUE FOR
FREE POSITION OF ACCELERATION PEDAL
SUGGESTIONSNo defect should be present or memorized.
The contact is set or the engine is started.
The value is
memorized at limit
or fa ilure to detect
the free pedal
po sition, or failure to
detect the completely
pushed down
position Check if the mechanic limitation of the potentiometer has been
a
ltered.
Check the command of the acceleration (friction, obstacles).
Check the resistance of the clapper potentiometer.
Change potentiometer if necessary.
Check the insulation, the continuity and the absence of contact
re sistance along the circuits:
pin 43 of calculator ♦ pin C of clapper potentiometer
pin 74 of calculator ♦ pin B of clapper potentiometer
pin 75 of calculator ♦ pin A of clappe r p otentiometer.
Remedy if necessary.
Th e po sition, of the
clapper is fixed
Check the resistance of the clapper potentiometer during the
operation of the clapper.
If the resistance varies, check the electric circuits connected to
the potentiometer.
If the resistance does not vary, check if the potentiometer is
mechanica lly coupled to the clapper.
Change the potentiometer if necessary.
AFTER REPAIRPerform again the conformity test.
vnx.su

19 - 5
19
COOLING - EXHA U ST - FUEL TANK
DISMONTING
The battery is disconnected.
The tube s of the radiator are stopped up with the MOT 453 de v i ce s .
Dismount the hoses from the radiator by means of the elastic collar pliers MOT 1202-01.
The two screws of the stand are taken off the upper traverse of the radiator and the radiator
is taken off. The radiator is emptied and the cooling liquid is retrieved.
R
EMOUNTING
Check the existence of the supporting bushings.
The radiator is mounted.
The jack s for the fixing on the radiator are mounted, as well as the radiator stands, and the
fixing sc rews are fastened (0,57 daN).
The MOT 453 devices are taken off.
The tube s that have been taken off are mounted back and the collars are tightened.
Note : When mounting, line up the marks from the hoses and the related parts.
The ba ttery is connected.
Th e filling and the draining of the cooling circuit is done.
Tightening moments:
- the screws for the radiator stands (M6- 2 pieces) - 0,57 daN.
RADIATOR
SPECIAL T OOLS
MO T 12 02 - 01 Pliers for elastic collars
MOT 453 Tubes’ plug
vnx.su

19 - 6
19
COOLING - EX HA U ST - FU EL TANK
COOLING FAN REPLACEMENT
for vehicles with air conditioning
1 6 5
3 2 4
7
8
DISMOUNTING
Di
sconnect the (-) plug of the battery.
Di sconnect the cooling fan connector (5).
Di sconnect the cooling fa n resistance connector (1). Mark t he mounting position iden-
tification of the two connectors.
Detach the wiring from clip (6).
Cut the clip attaching the wiring on the cooling fan assembly in point (7).
Dismount the four-attachement screws (3) of the cooling fan on the radiator, recovering the
washers (2) and (4). Remove the cooling fan assembly.
REMOUNTING
Check the condition of the fan propeller, cooling fan electri c motor, washers.
Tighten the attachement screw (3) of the assembly.
Replace the clip from point (7).
Mount the wiring of t he cooling fan assembly taking i nto the considera tion the mount-
ing position m arked before dismounting. This is to be fi xed by means of a clip in point (7)
and will pass trough the clip (6). Connect the cooling fan re sistance connector (1).
Connect the cooling fan c onnector (5). Observe t he m ounting position i dentification of
the two connectors. Connect the battery plug (-). In case the vehicle is equipped with progammable radio-
cassettes, electronic clock, e tc, these a re to be reset before returning the vehicle to t he client. Check t he c ooling fan opera tion: start the vehicle engine and disconnect the water
temperature sensor. The cooling fa n must start. Reconnect the water t emperature sensor,
then by means of the CLIP tester, erase the memorized failure related to the water t em-
perature sensor.
FAILURES
ERASING
vnx.su

19 - 9
19
COOLING - EXHA U ST - FUEL TANK
RESISTANCE COOLING FAN REPLACEMENT
for vehicles with air conditioning
De scription of t he opera tion :
Di sconnect the battery (-) term inal.
Di sconnect the resistance connector.
Di smount the two attachment screws of the re sistance.
Position the new resistance assembly.
Mount the two attachment screws of the resistance (tightening moment 4.5 Nm).
Connect the resistance connector.
Connect t he battery (-) terminal. In case the vehicle is equipped with programmable
radio-cassettes player, electronic clock, etc, those are to be re-programmed before return-
ing the vehicle to the client. Check the engine motor fa n operation.
vnx.su

19 - 10
19
COOLING - EX HA U ST - FU EL TANK
COOLING FAN REPLACEMENT
for vehicles without air conditioning
6 5
4 3 7
1
2
DISMOUNTING
Di
sconnect the (-) plug of the battery.
Di sconnect the cooling fan connector (7).
Dismount the three-attachement screws (6) of the cooling fan on the radiator, recovering the
attachement buffers (2), cross-pieces (3) and the washers (4) and (5).
Remove the cooling fan assembly (1).
REMOUNTING
Check the condition of the fan propeller, cooling fan electric motor, bushings and washers.
Tighten the attachement screw (6) of the assembly.
Connect the cooling fan connector (7).
Connect the battery pl ug (-). In case the vehicle is equipped with progammable radio-
cassettes, electronic clock, etc, these are t o be reset before re turning t he vehicle to the
client.
Check the cooling fan opera tion: start the ve hicle e ngine and disconnect t he water tem-
perature sensor. The cooling fan must start. Reconnect the water tempera ture sensor, then
by means of the CLIP tester, erase the memori zed failure related to the water t empera ture
sensor.
FAILURES
ERASING
vnx.su

19 - 20
19
COOLING - EX HA U ST - FU EL TANK
DIS M OUNT ING
In order to take apart the petrol tank from the car the following opera tions are in order:
The battery i s disconnected;
The tank is emptied of fue l;
The carpet in the boot is taken out;
The cabling case of the fuel-level transmitter i s taken off;
The collar fi xing the airi ng conduit on the tank lid is taken off;
The junctures of t he fue l-supply c onduits (goi ng- and return-) are taken off t he tank lid;
The driving axis of the spare-wheel stand is taken off;
The car is suspended on an elevator;
The spare-wheel is taken out of i ts holder;
The scre ws fixing the protection screen of the tank, and then the tank itself, are taken
off; The collars fixing the anti-t ilt valve juncture are taken off.
R
EMOUNTING
It is done in the reverse orde r of the taking apart opera tions. T
ANK FUEL
vnx.su