battery DACIA SUPERNOVA 2004 Manual PDF

82A
HORN - ENGINE IMMOBILISER
82A - 15
NOTE
For the RF remote control synchronisation, after the replacement of a kit, take into
account the fol lowing situations: - for the first RF remote control, perform the “ simple synchronised procedure”;
- for the second RF remote c ontrol perform the “specific synchronised procedure” .
C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by the means of the CLIP tester. This is possible
only if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed
by the state: 10G ANTI STARTING…………………………………………….. ACTIVE
After getting from DACIA database the repairing code (based on the code from the vehicle’s
key head), perform the following operations. 1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle. 2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “SUPERNOVA” and “050” equipping level.
5. Select the menu “ COMPUTER TEST” then choose “ ANTI STARTING”.
6. In the menu “ STAT E L IST” find t he state 10G “ANTI STARTING” which m ust be
“ACTIVE”.
7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL INTRODUCTION CODE” where you will write the
repairing code (formed of four figures), then validate it with the key “ENTER”. T he message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”.
9. Now the procedure is finished and you may start the vehicle engine.
AT TENT ION
You may perform three essays of introducing the repairing code; if aft er the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then put it
again, other t hree essays being allowed.
NOTE
This procedure does not decode the injection computer, but allows only the start of
the vehicle’s engine. After ten minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 16
D. SIMPLE S
YNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations:
- the RF remote control c ode is no longer i n the range of the E.C.U. decoder re ception,
because of consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E.C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.)
The following operations will be performed: - take off t he contact
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/o pening course.
- the procedure of synchronisation is finished; check the blocking/ unlocking by pushing
the RF remote control.
OBSERVAT ION
Duri ng those 10 seconds you can visualise by means of the CLIP tester the state 17G
“THE PROGRAMMING IN PROGRESS OR THE TIR/TRF
RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E .C.U. decoder
and will be performed as follows:
- connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket) of
the vehicle. - select the vehicle type “SUPERNOVA” and the “050” equipping level;
- select the m enu “ COMPUTERS TEST” then “ ANTI STARTING”
- enter the m enu “COMMAND MODE” and select “CONFIGURATION”
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice the RF remote control button; the doors will block and then unlock and the
anti starting indicator will t urn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 18
If the states
remain unchanged, check the following:
- electric connections of the decoding bushing
- the electric connections between the E.C.U. decoder and the decoding bushing
- the tension of the battery must have more than 8V when the starter is activated.
If all these are conformable, proceed to the replacement of the decoding bushing, and then
check again the a .m. states.
II. SOLVING MODE
When an electric ke y head (or both) is damaged, order (Info TECH LINE 0248/213766) a
new set of two electronic heads, subject to the vehicle type, as follows: TRF key head set – item no. 6001 543 684, 1 set, for DSN equipped with
anti intrusion (CLIMA or RAPSODIE)
TR-TRF key head set – item no. 6001 544 452, 1 set, for DSN without anti
intrusion (CLIMA or RAPSODIE)
TR key head set – item no. 6001 543 683, 1 set, for DSN EUROPA
Send to Tech Line (0248 213766), the chassis series no, the anti starting code of the damaged
key heads, the a nti starting code of the ne w key heads, and they will sent at their turn, to the
service center, the repairing code (taking into account that this code has a special regime). Additionally , there are necessary the new key heads, the E.C.U. decoder (obligatory TRF, if
the vehicle is equipped with central locking), the repairing code of the computer; proceed then to
the replacemen t of these items performing the following operation:
A) Replacement- c hecking electronic key heads :
Replace t he damaged key heads with the new ones (the metal insertions remain the same),
then by means of the CLIP tester, selecting COMPUTER TEST- ANTI STARTING- STATE
LIST, check following states with both keys:
If the states are in the following configuration, when setting the contact on, consecutively with
both keys:
ANTI STARTING……………………………………………..........ACTIVE
RECEIVED KEY CODE………………………………………….. ACTIVE
ACCEPTED KEY CODE…………………………………………PASSIVE DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 21
DIAGNOSTIC – FAILURES AND STATES INTERPRETATION
1. FAILURE OF COMUNICATION CLIP TESTER/ E.C.U. DECODER
RECOMMENDATION Check if the lines K and L are not disturbed by another computer of the vehicle.
Check the fuse state F15 (vehicles up to 01.06.2001) or F07 (vehicles after 01.06.2001).
Replace the fuse if necessary.
Check if the CLIP tester is not the cause of the failure; check if the tester communicates with
another computer of the same vehicle (injection computer).
M easure the tension of the vehicle’s battery (U> 10,5V). If necessary, charge the battery.
Check if the E.C.U. decoder is well connected to the vehicle’s wiring.
Check the right supply of the E.C.U. decoder: - presence of t he ground at pin A8 of the E .C.U. decoder
- supply + I.C. at pin A9 of t he E .C.U. decoder
Be sure that the diagnostic socket i s proper supplied, according to the circuit diagram.
Check the continuity and the isolation of the electric wiring on the corresponding pins layout.
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the connection tester CLIP – E.C.U. decoder can’t be established, then replace the decoder.
{ }
After establishing the communication with the tester, fix the
A FTER REPAIRING possible failures.
Perform a conformity checking.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 26
6. STATE 11G: ACTIVATE THE RF REMOTE CONTROL/ RECEIVED RF SIGNAL
INDICATION
If the 17D state is PASSIVE, do not apply the next diagnostic
because the E .C.U. decoder is unused (new).
RECOMMENDATION Perform first the remote control synchronisation Do not access the next diagnostic if the state 11G remains PASSIVE
when activating the RF remote control at the blocking and unlocking
of the doors.
Check the blocking and unlocking of the doors using the second RF remote control. If this
is one is operating, then the battery of the first RF remote control should be replaced.
Check the presence of +12 V(+DC) at the pin1 of the anti starting bushing.
Is there +12V ?
Perform using CLIP tester, the impulse detection test a t the pin 1 of the anti
starting bushing, when using the RF remote control.
Are any impulses when using the remote control ?
YES Replace the E .C.U. decoder.
NO Replace the anti starting bushing.YES
Check the isolation related to the ground of the electric wiring between:
E.C.U. decoder Pin B1 pole 1 anti starting bushing Pin B2 pole door locking switch
Pin B5 pole 3
Is the isolation related to the ground good?
YES Fix the electric wiring.
NO Replace the E .C.U. decoder.NO
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 29
FA
ILURES LOCATING BASED ON CLIENT CLAIM
(algorithm for damage locating)
A LP1. MISSING COMMUNICATION CLIP TESTER / E.C.U DECODER
RECOMMENDATION Check if the lines K and L are not perturbed by another computer
of the vehicle.
Check the situation of the F15 fuse ( up to 01.06.2001) or F7 (after 01.06.2001)
Replace it if necessary.
Be sure the CLIP t ester is not the cause of t he failure, by trying the communication with
another computer of the vehicle.
Check the tension of the battery (U>10,5V). If it is necessary, charge the battery.
Check the correct c onnection of the E.C.U. decoder to the wiring.
Check the supply of the E.C.U. decoder : - ground at pin A8 - supply (+IC) at pin A9
Be sure that the diagnostic socket is correctly supplied.
Check the continuity and the isolation of the electric wiring on the pins’ line corresponding to:
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the dialogue CLIP tester – E.C.U. decoder cannot be established, then replace the decoder.
When the communication with the tester is established, solve
AFTER REPAIRING the failures displayed by CLIP.
Perform a conformity checking.
DIAGNOSTIC
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 43
THE PIN CODE
The PIN code is formed of four figures and it can be used only for deactivating the anti intrusion
s ystem, if this operation can not be performed by pushing the deactivating button from the RF
remote control of the vehicle. For introducing the PIN code, perform as follows:-set on the contact key in the M position and take it off it for three times in seven seconds,
after which the anti intrusion LED indicator will switch on for three seconds; -set on the contact again on the M position and maintain it until the number of the L ED
blinks is e qual with the first figure of the PIN code, then take off the contact; -set on the contact in the M position and maintain it until the number of LED blinks is equal
w ith the second figure of the PIN code, then take off the contact;
-perform the above mentioned method in order to introduce the third and the fourth figure
of the PIN code;
-after that, the system is deactivated and the siren stops automatically;
- set on the contact again – the anti LED indicator must switch on, confirming in this way
that the c orrect introduction of the PIN code.
AT TENT ION
If it i s necessary the checking of the PIN code, t his will be pe rformed
only after al least 20 seconds have passed, since the anti intrusion ECU has been
connected to the vehicle’s wiring or since the connecting of t he vehicle’s battery.
The COBRA anti intrusion system can operate in t hree different modes (2,3 or 4).
For the Super Nova vehicles, the system has been programmed to work in the second operation
mode. If by mistake the PIN code was introduced in less than 20 seconds since the battery
connecting or since connecting the anti intrusion ECU, this can involve the change of the operation
way of the system, which will generate errors during the operation. There is, although, the possibility
of reprogramming the correct operation way (type 2) and in this purpose, perform the following
operations : - disconnect and then reconnect the anti intrusion ECU; when connecting the anti intrusion
ECU the anti intrusion LED indicator will switch on once, confirming the correct connecting;
-af ter at least 5 seconds from the previous operation, but no more than 20 second from it,
perform the following operation s:
-s et on the contact key in the M position for three times and then release it;
- the anti intrusion LED indicator will switch on for three seconds and then will switch off;
- set on again the contact key in the “M” position and maintain it, counting two blinks of the
anti intrusion LED indicator, then take off the contact;
- the LED indicator will blink for two times in two series, confirming in this way the proper
performance of the previous operations;
press the doors locking button of the dashboard, in order to lock and unlock the doors; the anti
intrusion LED indicator must not blink;
vnx.su

83
INSTRUMENT PANEL
CONNECTOR C
1. Instrum ent panel lighting
2. Ground
3. Anti starting indicator
4. Supply (+ IC)
5. Free
6. Injection failure indicator
CO NNECTOR D
1. Battery charging circuit failure indicator
2. Fuel minimum level warning
3. Free
4. Free
5. Free
6. Free
7. Free
8. Free
83-2
The corresponden
ce between the positions from A,B,C,D connectors of the instrument panel
and the components of the vehicle electric equipment is the following :
CONNECTOR A
1. Free
2. Rear window defrosting indicator
3. RPM
4. Cooling fluid temperature indicator
5. Oil pressure warning
6. Cooling fluid temperature warning
7. Left turning indicator
8. Left turning indicator
9. Hazard lights indicator
10. Instrument panel ground
CONNECTOR B
1. High beam indicator
2. Free
3. Free
4. Right turning indicator
5. Right turning indicator
6. Supply ()+DC)- after contact
7. Hand brake, braking system failure warning
8. Brake pads wear indicator
9. Free CO
NNECTORS ( until 01.06.2001)
vnx.su

83
INSTRUMENT PANEL
83-4
CO
NNECTOR X
1. Low beam indicator
2. Anti starting indicator
3. Supply(+IC) anti starting indicator
4. Injection failure indicator
5. Oil pressure warning
6. Water temperature indicator
NOTE
In case of the interventions on the instrument panel, check the existence of the
rubbe r i solati ng ele ments on the windsc re en lower c ross bar, pl ac e d behi nd the
instrument panel. For the vehicles corresponding to the pollution norm EURO 2000, at the X c onnector,
position 4 is “ OBD anti-pollution failure indicator”. The i nstrument panel is provided with thre e connectors having the following pl ugs
correspondence:
CONNECTOR V
1. Instrum ent panel lighting
2. Ground
3. Rear window defrosting indicator
4. High beam indicator
5. RPM
6. Supply (+DC) after contact
7. Free
8. Ground
9. Right turning indicator
10. Left turning indicator CONNECTOR Z
1. Hazard indicator
2. Water temperature warning
3. Supply (+DC) after contact
4. Ground
5. ICP and handbrake warning
6. Brake pads wear warning
7. Fuel level indicator
8. Fuel level minimum warning
9. Battery charging indicator
CO
NNECTORS(after 01.06.2001)
vnx.su

83
INSTRUMENT PANEL
DISMOUNTING
Disconnecting battery.
Dismounting flexible shaft( speedometer cable) from the gearbox.
Dismounting control cable from the recyclin g flap.
Dismounting steering wheel and the steering wheel casing.
Dismountin g dashboard lower fairing.
Dismountin g documents compartment.
Disconnect documents compartment lamp.
Dismountin g central console.
Dismounting flaps control cables from the climate control unit.
Discon necting: cigarette lighter, climate control lighting, ashtray lighting, climate control switch .
Dismounting headlamps adjustment control from the dashboard.
Dismounting dashboard from the windscreen lower cross bar.
Disconnecting flexible shaft (speedometer cable) from the instrument panel.
Disconnecting air conducting ducts to aerators.
Disconnecting front wiring from the instrument panel and from the dashboard wiring.
Dismounting instrument panel attachmen t clamps from the dashboard.
Dismountin g clamps from the instrument panel.
Mounting clamps on the new instrument panel.
Mounting instrument panel with clamps on dashboard.
Connecting flexible shaft to the instrument panel.
Connecting front wiring to the instrument panel and to the dashboard wiring.
Positioning and fixing air conducting ducts.
IN
STRUMENT PANEL REPLACEMENT
83-5
vnx.su