sensor DACIA SUPERNOVA 2004 Repair Manual

ENGINE E7J-A-2/6010
10 - 3
ENGINE AND LOWER ENGINE UNITS
MOTOR-PROPELLING GROUP
Di sconnect the wiring c onnector from t he
reverse driving contact. The right-side planetary transmission is un-
coupled as follows:
-the brake-stirrup set is dismantled;
-disconnect the wire for the brake pads
wear indicator; -the t wo screws for fixing the shock-
absorber of the steering-swivel stand are taken
off;
The steering-swivel stand is tipped up and
the planetary t ransmission is taken out from
the planetary pinion of the gearbox;
The l eft-side planetary transm ission is un-
coupled as follows:
-the steering-swivel screw-nut is dis-
mantled; -t he scre ws for fi xi ng t he pl a neta ry
transmission on the gearbox a re taken off; -the brake-stirrup set is dismantled;
-the e lectric wire of the wear-and-abra -
sion light-i ndicator is taken off; -the t wo screws for fixing the shock-
absorber of the steering-swivel stand are taken
off; -the steeri ng-swivel stand is t ipped up
and the planetary tra nsmission is taken out; The fuse-box in the engine compartment
is dismantled.The following are disconnected: -connector 1 from the UCE injection
(pull flap 2, then disconnect);
-the front cabling of the engine;
-the connector of t he shock-sensor;
-the ventilator connector;
-the mass wire on the gearbox.
The battery protection screen is dis-
mantled.
The following are taken off:-the linking pipes coming from the ra -
diator, by using the pincers for elastic pipe-
collars MOT.1202-01B ;
-the linking pipes coming from the de-
gassing vessel, by using the pincers for elas-
tic pipe-collars MOT.1202-01B ;
-the pipes for a ir-conditioning coming
from the therm ostat stand and the water-pi pe;
12
vnx.su

ENGINE E7J-A-2/6010
10 - 7
ENGINE AND LOWER ENGINE UNITS
Rotation sensor 2 is taken off;
The electric connections of the start er are undone;
The start er is taken off;
Electric connector 1 of the backwards motion contactor is taken off;
The engine cabling fa stening to the gearbox is dismantled;
The screws and screw-nuts of the gearbox assembly are taken off; SEP
ARATION ENGINE - GEARBOX
RE -ASSEMBLY ENGINE - GEARBOX
The separa tion operations are executed in the re verse order;
The screws and screw-nuts are tightened onto the couple.
TIGHTENING COUPLES (daNm) Rota tion sensor 0,8
Screws of the starter 4,4
Fixing the gearbox onto the engine:
- screw-nuts M 10 4,4
- screws M 10 - 90 4,4
- screws M 10 - 35 2,1
SEPARA TION - DISMANTLING
vnx.su

ENGINE E7J-A-2/6011
UPPER AND FRONT ENGINE UNITS
SPECIAL TOOL- AND-CHECK SETS
MOT.1202-01 -”CLIC” collar-pincers
MOT.1505 -Device for measuring belt tension
MOT.484 -Device for jacket maintaining -Wrench for angular tightening
-Pincers for elastic collar
TIG H TENING CO UPL E S (daNm )
S crew-nut of stretching runner/pulley 5
Screw of crankshaft pulley 2+68
o+/-6o
Screws of pendular suspension stand 6.2
Screw-nut of hydro-elastic buffer 3.7
Wheel Screws 7.5
Co mbustion-head Screws 2+97
o+/-2o
To take apart :
-the connector of the induction coil;
-the fue l hoses (t he going- and re -
turn circ uit); -the connectors of the injectors;
-the plugs of the sparks;
-the induction coil.
11 - 3
CYLINDER HEA D FITTING
D
IS M O UNT ING
The car is placed on a two-column lift -
ing stand; The battery i s disconnected;
The cooling circuit is emptied at the
jack situated at the lower pa rt of the radia-
tor; The distribution belt is taken apart (see
Chapter Distri bution Belt);
The following are taken apart: -air-filter;
-the c onnector of the c lapper-posi-
tion potentiometer (1); -the acceleration cable;
-the connector of the atmosphe ric
pressure sensor (2);
-the co nnector of the step-by-step
engine (3); -the connector of t he air temperature
sensor (4) on the intake collector;
vnx.su

ENGINE E7J-A-2/6012
FUEL MIXTURE
CH ARACTERISTICS
ENGINE
Car Gearbox Ty p e Index Cylinder Stroke Cylinder
bore length volume
(mm) (mm) (cm3)
SupeRNova JH3-050 E7J A-2/60 75,8 77 1390 9,5/1
Check-ups in idle mood*
Motor Emisii poluan
i
Fuel
Type Index Mode CO(%) CO2(%) HC Lambda (minimum
(rot/min) (1) ppm l octanic number)
E7 J A-2/60 750+/50 0,5 14,5 100 0,97.. .. Unleaded petrol
max min max ....1,03 (CO95)
(1) at 2500 rot /min the CO value must be max. 0.30%;
* For water t emperature over 80
oC and after stabilizing at 2500 rot/mi n for 30
seconds; then turn ba ck into idle mode and the level of fumes is measured. The water-tempera ture a nd air-t emperature sensors are type NTC (negative
temperature coefficient), and the vari ation of their re sistance as to temperature
has the following evolution:
T (0C ) 0 20 40 80 90
A ir-T sensor
11970 - 7470 4045 - 3060 1600 - 1315 - -
R (Ohm)
Engine T 8000 - 67 00 3000 - 2600 1300 - 1100 300 - 270 215 -200
sensor
R (Ohm)
12 - 1
vnx.su

ENGINE E7J-A-2/6012
FUEL MIXTURE
DENOMINATION PARTICULARITIES
Computer 90-ways connector
Injection system Multi-point sequential
Ignition PINIS R
W
Static wi th a double coil
Computer controlled ignition R
A-B1W
R
A-C0,5 W
R
B-C0,5 W
R
1-47+/-1KW
R
2-37+/-1KW
Detonation se nsor Piezoelectric type SAGEM
Tightening moment = 2 daNm
RPM SENSOR ELECTRICFIL or SIEMENS R = 200......270 W
Spark plugs EYQUEM - type RFN 58 LZ
CHAMPION - type RC 87 YCL
Fuel filter For EURO 96:
Attached under the vehicle in front of the fuel tank
Replacement on the occasion of the scheduled inspections
For EURO 00:
Into the fuel tank, attached on the fuel pump assembly.
It is no t replaced separate.
Fuel pump Immersed in the fuel tank
For EURO 96: - Flow: 1,3 l/min - Pressure: 3 bars at 12V tension
For EURO 00: - Pressure: 3,5 bars at 12V tension
Pr essure controller For EURO 96:
Pressure controller attached on the injection ramp
Controlled pressure: - 3 +/- 0,2 bars at zero depression- 2,5 +/- 0,2 bari at a depression of 500 mbars
For EURO 00:
Mounted into fuel tank on the fuel pump assembly
Controlled pressure: 3,5 bars
El ectric injectors SIEMENS
R = 14,5 +/- 1 W la 20
0C
+ 12 V supply
Step by s tep engine R
A-D = 52 +/- 5 W
R
B-C = 52 +/- 5 W
12 - 2
CH ARACTERISTICS
vnx.su

ENGINE E7J-A-2/6012
FUEL MIXTURE
12 - 3
CHARACTERISTICS
DENOMINATION PARTICULARITIES
Valve potentiometer
Canister purging
valve
Oxygen sensor
At mospheric
pressure sensor
idle at maximum
acceleration
A - B 1300 W130 0 W
A - C 1500 W 2000 W
B - C 2000 W 1300 W
SAGEM
Supply tension= +12 V
R = 26 +/- 4W la 23
0 C
NGK
For EURO 96: an oxygen sensor attached on upstream of
catalyzer Generate d tension at 8500C:
- rich mi xture 750 +/- 50mV
- sa lt mixture 150 +/- 50 mV
He ating resistance R
A-B = 3 ..... .. 15 W
For EURO 00: two oxygen sensors attached one on
upstream and the othder one on downstream of catalyzer
DELCO ELECTRONICS
Stopped engine – shows an atmospheric pressure of
950...1050 mbar
Idle engine - 330 +/- 40 mbar
vnx.su

ENGINE E7J-A-2/6012
FUEL MIXTURE
The following are taken apart:
- air-filter;
- accelera tion cable;
- injection ramp ( see Chapter Injec-
tion ramp );
The electric connectors are uncoupled: - atmospheri c pressure sensor;
- air tempera ture sensor;
- step-by-step engine;
- clapper potentiometer.
The fuel supply conduits are taken apart (bot h going- and return);
The clapper c ommand lever is uncoupled and the body of the clapper is taken off;
The screws and screw-nuts fixing the intake collector a re taken apart .
RE-MOUNT ING
The fittings of the intake collector are re placed;
The same steps are taken as in the case of the dismantling, only in the reverse order.
Tighten the inlet manifol d screws and nuts at the require d moment of 2.5 daNm. T
IG H TENING CO UPL E (daNm)
Screws and screw-nuts for intake collector 2.5 INTA
KE COLLECTOR
12 - 5
DISMOUNTING
vnx.su

E7J-A-2/60 ENGINE13
PUMP SUPPLY
AIM:
To avoid accidental fire s owing to fuel leaks, which can be caused by an accident.
F
UNCT IO NING:
The shock-sensor lies in the engine compartment: it is mounted on the left-side shock-
absorber column. Du ring a shock, the ball of the sensor goes out of its slot, a nd thus achieves the breaking
of the electri c c ircuit be tween the relay commanding the petrol-pump and t he pe trol-pum p
itself.
PLACING B ACK THE SH OCK-SENSOR IN OPERAT IONAL MO DE
In order to resume the functioning of t he shock-sensor it will suffice to press its top,
and thus replace the ball in its former position. BREAKING FUEL SUPPLY
13 - 1
vnx.su

E7J-A-2/60 ENGINE16
16 - 7
ST ARTING AND CHARGING
IDENTIFICATION
ENGINE STARTER
E7J - A-2/60 D 907 - M00 2T 13581
DIAGNOS TICATION
S pecial device: CLIP - SAGEM-TECHNIC TESTER which measures the battery
voltage and the intensity absorbed by the starter.
ANOMALOUS FUNCTIONING THAT CAN BE SETTLED
-Battery failure –contact drop on the starter when starting the engine.
-Blocked starter (t he absorbed curre nt is very high);
Coupling relay defect (the current absorbed is very weak).
In order to do the measurements one must carry t he engine in starter mode, thus pre -
venting the engine to run.
To do t hat, the revolution sensor (located in the c lutch cra nkcase) should be t aken apart .
Remark: After doing these tests, erase the possible defects memorized
by the calculator with the tester.
STA RTER
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 1
S
TATIC IG NIT IO N
PRE S E NT
AT IO N
The system is made up of:
- electronic control unit;
- double ignition coil;
- four sparking plugs;
- spark plugs.
DES CRIPT IO N OF FUNCT IO NING PRINCI PL E
Accordi ng to the data received from
various sensors, but essentially according
to the revolution ratio and the load of t he
engine, the electronic control uni t will de-
termine the ignition advance; it will also
identify the cylinders that are set at the
upper center point and, consequently, will
command the re spective coil. This c auses the spark at the level of the
two cylinders t hat are at the upper center
point, thus interrupting the m ass-setting of
the respective coil. T
HE CO IL
The system c ontains a doubl e c oil, con-
trolled by the calculator.
Coil no. 2 has an electric connector (1) with
four ways, whi ch si m ultaneousl y produc e
s parks at cylinders nos. 1 and 4, when it i s
commanded by pin no. 32 of the i njection cal-
culator, and on cylinders no. 2 and 3 when it
is commanded by pi n no. 1 of the same cal-
culator.
ELECTRIC CONNECTOR
Pins Function
AC ommands ignition at
cylinders nos. 1 and 4
BC ommands ignition at
cy linders nos. 2 and
CFuel supply (+DC)
inter - pin Rezisten
a
check între pini
A-B 1 W
A-C 0,5 W
B-C0,5 W
HT - HT 11 KW
IGNITION SYSTEM
vnx.su