light DACIA SUPERNOVA 2004 Service Manual

81
REAR AND INTERIOR LIGHTING
81 - 7
A.
FOR VEHICLES MANUFACTURED TILL 01.06.2001
The fuses are protecting the following electric circuits:
FUSE
NUMBER FUSE
TYPE
PROTECTED CIRCUIT
Clock, radio, STOP contact, climate blower relay control
Reverse driving contact
UCE decoder, speed transducer, instrument panel supply, diagnostic
socket, AC starting button, UCE anti intrusion
Turning and hazard lights
Front/rear parking lights, lighting: switches, instrument panel, climate
control, documents compartment, cigarette lighter, ashtray, radio
Cigarette lighter, instrument panel (anti-starting indicator), front right
ceiling lamp, UCE anti intrusion, anti intrusion indic
ator, diagnostic socket
Windscreen wiper-washing switch, windscreen wiper timer
Rear window defrosting
Climate blower
Left fo g lamp
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10 15A
5A
15A
7,5A
5A
15A
15A
20A
15A
5A
COCKPIT FUSE BOX
vnx.su

REAR AND INTERIOR LIGHTING
81
81 - 8
On the fuse box, 6 fuses modules are attached, protecting the following consumers:
FUSE
NUMBER FUSE
TYPE
PROTECTED CIRCUIT
Left high beam
Right high beam, high be
am indicator
Left lo w b e am
Right low beam, low beam indicator
UCE decoder, FLASH relay, anti starting bushing
Radio, windscreen wiper motor.
10A
10A
10A
10A
15A
10A
F11
F12
F13
F14
F15
F16
COCKPIT FUSE BOX
vnx.su

81
REAR AND INTERIOR LIGHTING
B. FOR VEHICLES MANUFACTURED AFTER 01.06.2001
AND VEHICLES RESPECTING EURO 2000 POLLUTION NORM
The fuses are protecting the following electric circuits:
FUSE
NUMBER FUSE
TYPE
PROTECTED CIRCUIT
Clock, radio, STOP contact, climate blower relay control
Reverse driving contact
UCE decoder, speed transducer, instrument panel supply, diagnostic
socket, AC starting button, UCE anti intrusion.
Turning and hazard lights
Front/rear parking lights, lighting: switches, instrument panel, climate
control, documents compartment, cigarette lighter, ashtray, radio.
Cigarette lighter, clock, instrum
ent panel (anti-starting indic ator), front right
ceiling la mp, UCE anti intrusion, anti intrusion indicator, diagnostic socket.
UCE decoder, FLASH relay, anti starting bushing
Rear window defrosting
Climate blower
Left fo g lamp
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10 15A
5A
15A
7,5A
5A
15A
15A
20A
15A
5A
81 - 9
COCKPIT FUSE BOX
vnx.su

REAR AND INTERIOR LIGHTING
81
81 - 10
Pe cutia de siguran
e sunt fixate 6 module siguran
e fuzibile ce protejeazã urmãtorii consumatori:
FUSE
NUMBER FUSE
TYPE
PROTECTED CIRCUIT
Left high beam
Right high beam, high be
am indicator
Left lo w b e am
Right low beam, low beam indicator
Windscreen wiper-washing switch, windscreen wiper
timer
Radio, windscreen wiper motor.
10A
10A
10A
10A
15A
10A
F11
F12
F13
F14
F15
F16
COCKPIT FUSE BOX
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 1
This type of anti starting syste m is based on the key recognition, which has a special construction.
It may be separated in two elements which can be identified in the following way (pict.1): the key
he ad (pos.A.) made of plastic, which can be dismounted and the metal insertion (pos.B.), which is
fixed an d ensured by clipping in the key head.
In the key head, there is a coded independent electronic circuit, which is functioning without
battery. When setting the contact on, the anti starting bushing, placed around the starting contact,
is enquiring and catching the coded signal emitted by the key head, then sends it to the Electronic
Control Unit (E.C.U.) decoder. This one is attached on the front left pillar, under the lower casing
of the dashboard and has the function of receiving the code sent from the bushing. If the decoder
recognises the key code then it will send a coded signal to the injection computer, which compares
it with the previous memorised code and will authorise or not the start of the engine.
We mention that the system with radio frequency remote control (RF) of the doors blocking
/unlocking, has no influence to the anti starting system. In this case, the key head has a different
construction, having an activation button of the remote control and a red LED, which is lighted in
the moment of blocking/unlocking the doors, by pushing the key button. Inside the key head
there is the coded electronic circuit for the anti starting system and an imprinted electronic circuit,
s upplied by a battery, for t he RF remote control operation of blocking/unlocking the ve hicle
doors.
The anti starting system is activated after approximate 10 seconds from the breaking of the
contact and is visualised by the blinking of the anti starting indicator placed on the instrument
panel.
If the battery is low charged, the t ension drop on the starter, at starting,
may cause the activation of the anti starting system and the start of the engine is
impossible.
pict.1
GENERALITIES
AT T ENTION
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 3
GENERALITIES
The anti starting bushing (picture 5) is located around the starting contact a nd is accessible
after the dismounting the steering wheel’s cases. It catches the signal from the key head and then
s ends a coded signal t o the E .C.U. decoder.
The vehicles equipped with RF remote control keys for blocking/ unlocking t he doors are
provided with another anti starting bushing which transmits to the E.C.U. decoder also the signal
received from the RF remote control.
The recognition of the two types of decoding bushings is realised by means of codes labelled
on their body, as follows :
- code 042264J - for vehicles w ithout RF remote control
- code 8200044257 - for vehicles with RF remote control
The E.C.U. decoder (picture 6) has the
following functions :
- decode the signal received from the anti
starting bushing ;
- sends a c ode to the injection computer
in order to authorise the engine starting.
- controls the anti starting indicator of the
instrument panel - receives the coded signal from the anti
NOTE
In case both keys we re lost, the code of the key head (8 characters) and the code of
the m etal insertion (4 characters) can be red from the vehicle invoice. If al so the i nvoice
was lost, the two mentioned codes can be found out based on the chassis series number
of that vehicle, accessing the database of the DACIA manufacturer, calling the TECH
LINE.
pict.5
pict.6
starting bearings, for the vehicles equipped with RF remote control;
- commands the blocking/unlocking of the doors, if the vehicle is provided with RF remote
control keys;
- commands the dome ceiling lighting, for the vehicles equipped with this system.
E.C.U. DECODER
ANTI STARTING BUSHING
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 4
NOTE :
The vehicles equipped with this anti starting system, have a type of decoder, and those
provided also with RF remote control for locking/ unlocking doors have another type
of decoder.
The identification of the two types of E.C.U. de coder i s realised by the inscriptions on
the labels as fol lows: -code P8200032783H and the inscription TRANS-PLAF for the vehicles without
RF remote control ;
-code P82000 32776H and the inscription TRF-TRANS-CAR for the vehicles
with RF remote control.
ANTI STARTING INDICATOR
It is located on the instrument panel (picture 8, position A) and has the following functions: - signals the activation of the anti starting system
- signals the case of non identifying the key head
- signals the entrance in the operation mode “resynchronisation” of the remote controls,
RF with E.C.U. decoder, for the vehicles which use the RF remote control.
pict.7
pict.8
A
GENERALITIES
The dome ceiling lighting is activated subject to the position of the switch
(picture 7, position 1):
- position A the ceiling lights permanently
- position B the ceiling turned off
- position C dome ceiling lighting; this will light for 5 seconds after a front door closing or
after the command of unlocking the doors with the RF remote control. This delay turns out in the
moment of setting the contact.
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 5
When the contact is off and the anti starting system is activated, without any existing
failure,
the anti starting indicator must blink slowly (a blink per second).
After setting the contact on, the anti starting indicator must light for 3 seconds and then turn off.
If after setting the contact on, the a nti start ing system doesn’t work properly, then the anti
starting indicator will blink rapidly (2 blinks per second). GENERALITIES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 11
A.
ECU DECODER REPLACEMENT PROCEDURE AND ANTI STARTING
CODE MEMORISING
The new E.C.U. decoder is always not coded. After its mounting on the vehicle it is necessary
that this one is memorising the anti starting code in order to be operational.
NOTE
If only the E.C.U. decoder i s replaced, there i s no need of an i ntervention to t he
E.C.U. injection (injection computer), which will keep the old anti starting code.
AT TENT ION
After the E.C.U. de coder memorised the anti starting c ode, this code cannot be erased
or replaced with another one.
In order t o perform this procedure, one of the keys of t he ve hicle and the CLIP tester are
needed. Perform as follows: 1. Connect the CLIP tester to the diagnostic socket and to the battery (or the lighter
socket) of the vehicle. 2. Read the configuration of the old E.C.U. decoder in the following way, before dismounting
it from the vehicle:
- select t he type “SUPERNOVA” and the “050” equipping level;
- enter the menu “ COMPUTER TEST” then choose “ ANTI STARTING”
- access “COMMAND MODE” then “CONFIGURATIONS READING”
- note the configurations found : petrol/d iesel, programming with 1 or 2 keys, ceiling delay,
the type of the doors’ blocking switch (CPE), etc.;
3. Get back to the m enu “TEST COMPUTERS”
4. Remove the old E .C.U. decoder and replace it with a new one, the contact being off.
5. Enter the menu “ANTI STARTING”, then select “ STATE LIST”. If the E.C.U. decoder
is new, you must find the following states:
18G FIRST CYCLE MEMORISING………………........................ ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………….. ACTIVE
19D UNLOCKED KEY PROGRAMMING………………............. ACTIVE
OBSERVAT ION
If the states 19G and 19D are not “ACTIVE” this means the E.C.U. decoder has
been already used, so it isn’t new and cannot memorise another anti starting code.
Access the menu “COMMAND MODE” and then “CONFIGURA TION”, where you will
configure the new E.C.U. decoder in the same way as the old one: petrol, 1 key, ceiling delay,
impulsion doors blocking switch, etc. selecting one by one these configurations, which you’ll
validate with “CLICK” on the blue button on right top of the screen. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 12
7. Get back to “ TEST COMPUTERS”
8. Set the contact on for 2 seconds in “ M” position, without start ing the engine. T he a nti
starting indicator will begin to blink rapidly.
9. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE…………………………………………ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………………PASSIVE
10. Take t he contact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”.
11 . The anti starting indicator will blink rarely.
12. Get back to the “STAT E LIST”, which now, must be like that:
18G FIRST CYCLE MEMORISING ………………………………ACTIVE
19G NOT PERFORMED KEY PROGRAMMING... ………………PASSIVE
19D UNLOCKED KEY PROGRAMMING………………………. PASSIVE
13. Set the contact in “ M” position for 2-3 seconds i n order t o send the code to t he E .C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI START ING” is “ACTIVE”.
Pe rform the synchronisation of the TRF remote control with the decoder (with 1 or 22 keys).
OBSERVAT ION
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows: -take the c ontact off; wait for 10 seconds, then the anti starting indicator will
blink; -in the m enu “COMMAND MODE” access “ ACTUATORS” then validate “
FORCED PROTECTION MODE” launching the command from the bl ue button
s ituated on the right topside of the screen. “COMMAND IN PROGRESS” will be
displayed and then “FINISHED COMMAND”.
-in the menu “STATE LIST” search for the state 10G ”ANTI STARTING”,
which must be “ ACT IVE”;
-set the contact on “M” position; the anti starting indicator will blink rapidly,
and the engine starting is i mpossible; - remove the key from the contact and check then the engine starting with both
keys, so the procedure is finished. PROCEDURES
vnx.su