light DACIA SUPERNOVA 2004 Owner's Guide

80
BATTERY - FRONT HEADLIGHTS
80 - 5
FOG LAMPS
DISMOUNTING – REMOUNTING
Disconnect the fog lamp (A) connectors from the vehicle wiring.
Dismount the two fog lamp attachment nuts (B and C) on the front bumper.
Remove the fog lamp off the bumper.
Position in the bumper the new fog lamp.
Mount the two fog lamp attachment nuts (B and C).
Connect the fog lamp (A) connectors to the vehicle wiring.
Check the operation of the fog lamps.
NOTE:
After mounting t he fog l amps, it is obl igatory to perform their adjustment.
vnx.su

80
BATTERY - FRONT HEADLIGHTS
BULBS REPLACEMENT80 - 6
HEADLAMP BULB REPLACEMENT
DISMOUNTING
Disconnect the connector (1).
Disconnect the supply wires of the parking bulb and remove the parking bulb.
Remove the rubber protector (2).
Release t he attachment clamps (3) and remove the low-main beam bulb.
REMOUNTING
Perform the dismounting operations in the reverse order.
NOTE:
In case the headlamp is equipped with a halogen bulb, do not touch its glass balloon
directly by hand.
FRONT TURNING BULB REPLACEMENT
DISMOUNTING
Disconnect the bulb supply wires
Rotate the holder (4) and remove it.
Remove the burnt bulb from the holder.
REMOUNTING
Pe rform the dismounting operations in the reverse orde r, with the checking of the correct
holder (4) positioning to avoid dust and humidity penetration in the headlamp assembly .
The turning lamps are using orange color bulb; when replacing the bulb, use the same bulb type.
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 7
HEADLAMPS ADJUSTMENT
MEETING LIGHTS ADJUSTMENT (LOW BEAM) This is performed by acting upon the V screw
(vertically p lane adjustment) or H (horizontally
p lane adjustment). By screwin g, t he lighting beam
is ”lowering” and by unscrewing is “ascending”.
Check if the lighted area i s centered on the
vertical axis and if the optical separation at 15°
coincide with the headlamp lighting. An error
of 1 cm is admissible.
A lighting beam displaced towards left has
the aspect shown in ( pict.a) and a lighting beam
displaced towards right has the aspect shown
in (pict.b).
RO AD LIGHTS ADJUSTMENT (LONG BEAM)
Check the position to coincide with the
adjustment performed for low beam a nd with
the lighting beam distributed between the two
vertical lines on the panel. When checking the long beam, the lighting
center of the ellipse, must be located on the
cross marking the screen center.
If a m ajor de viation c ompared with t he low be am i s noticed, i t is re commended t he bul b
replacement, this one being in most of the cases, responsible for such defect.
pict.a
pict.b
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 8
HEADLAMPS ADJUSTMENT
FOG LAMPS ADJUSTMENT
The fog lamps adjustment is to be performed in the following conditions:
- the vehicle to be placed on a horizontal surface;
- the vehicle has not passengers inside the cockpit or weights in the trunk;
- the tires a re pressurized a t the manufacturer prescribed pressure.
Further on, proceed as follows:
Bring the vehicle at the working place.
Position the adjustment device (headlamp adjustment device – E) in front of an optical center
of a fog lamp.
Switch on the fog lamps.
Rotate the adjustment screw of the fog lamp (D), so that an adjustment of 2 % is obtained and
the separation between the lighted area and the dark one from the adjustment device is located
under the marked line (G).
This adjustment is performed in the same way as for the meeting lights adjustment.
Bring the adjustment device in front of the optical center of the second fog lamp.
Perform the fog lamp adjustment.
Switch off the fog lamps.
G
E
vnx.su

81
REAR AND INTERIOR LIGHTING
81 - 1
BULBS REPLACEMENT
BULB REPLACEMENT OF THE REAR TURNING, PARKING AND BRAKE STOP LIGHT
Disconnect the battery.
Push towards interior the two attachment clips (1 ), then extract the plastic cap (2).
Disconnect the connector (6).
Push upwards the attachment clips (3) of the printed circuit plate (4), swing it and pull out the
plate from the attachment shoulders (5).
For remounting perform the dismounting operations in the reverse order.
FOG LAMP BULB REPLACEMENT
Di smount the attachment scre ws (1) of the
fog lamp glass and remove the glass;
Remove the burnt bulb and replace it.
REPLACEMENT OF THE LICENSE PLATE LAMP BULB
Dismount the lamp attachment screws.
Replace the burnt bulb.
For remounting, perform the dismounting operations in the reverse order.
vnx.su

REAR AND INTERIOR LIGHTING
81
81 - 2
BULBS
Hugh/low beam lights Two phases bulb R2-12V-40/45 W
He adl a mp swith flange holder P45t41
Parking lights Bulb 12V-4W with holder BA 9s
Front turning lamp Bulb 12V-21W (colored) with holder BAU 15s
Fog lamps Halogen bulb H3, 12V-55W with holder Pk22s
Rear Parking, stop lights Bulb 12V-21/5W with holder BAY 15d
lamps Turning and reverse driving Bulb 12V-21W with holder BA15s
Rear fog lamps Bulb 12V-21W with holder BA 15s
Lamps: side signaling, trunk lighting Bulb 12V-5W with holder W2,1x9,5
License plate, ceiling, document compartment Bulb SOFIT 10 x 35 type AS02; 12 V-5W
lamps with holder Sv 8,5
Lamp STOP-S3 on the ceiling Bulb 12V-21W type C21W with holder Sv 8,5
Instrument panel Bulb 12V-1,2W holderW 2 x 4,6d BULBS
vnx.su

81
REAR AND INTERIOR LIGHTING
THE REAR DRIVING LAMPS NOT WORKING81 - 3Check the contact supply.
The contact is supplied;
the lamps supplying wire is disconnected
or broken.
Check the F 01 fuse.

Fu se F01 is burnt; replace t he fuse .F
01 is good:
bridge across the c ontact plugs.
Lamps a re working; replace the contact. Lamps are not working.
The contact is not supplied;
the contact supply wire is disconnected
or broken.
DIAGNOSTIC
vnx.su

REAR AND INTERIOR LIGHTING
81
81 - 4
FOG LAMPS NOT WORKING
F 10 fuse is burnt; replace the fuse.
The relay is supplied.
Ground wire broken. Check the fuse F 10.
F
10 fuse is good.
Check the supply of the R1 relay.
The relay is supplied.
Check the lamps supply. The relay i s not supplied. Is there + 12 V
at pole 4 of the fog lamps contact ?
Disconnected wiresor defect contact. Lights switch
device
defect or F05 fuse burnt.
Lamps are not supplied .Check the fog lamps control relay.
Relay defect.
Replace the relay. Relay good. Lamps supplying
wire
broken or disconnected.
Yes No
DIAGNOSTIC
vnx.su

81
REAR AND INTERIOR LIGHTING
81 - 5
BRAKE STOP LIGHTS NOT WORKING
Check F 01 fuse.
F 01 fuse burnt ; replace it.Fuse is good.
Bridge across the brake stop contact.
Stop lamps are lighting. Replace the contact. Stop lamps are not lighting.
Check the contact supplying.
Wire is broken: replace the wire.Contact is supplied. Lamps supply
wi re is disconnected or broken.
DIAGNOSTIC
vnx.su

REAR AND INTERIOR LIGHTING
81COCKPIT FUSE BOX81 - 6
DISMOUNTING
Disconnect the (-) plug of the battery.
Turning the button
(4) open, then carefully remove the access little door (1) to the fuse box,
placed under left side dashboard. Dismount the attaching screws (2) of the fuse box on back of the little door.
Rotate the fuse box in order to have access at the connectors of its back then carefully discon-
nect the wiring connectors. If it is necessary the replacement of the module (3 ) attached on the
fuse box, for the fuses F11 – F16, first note the position of the wires connected to these fuses,
then perform the wires disconnecting .
Remove the fuse box.
REMOUNTING
Connect the wiring connectors to the fuse box printed circuit. Observe the form correspon-
dence of each connector with its drawing, marked on the printed circuit of the fuse box. Connect the wires corresponding to the fuses F11 – F16, if those have been previously disconnected.
Position the wires appointed for the fuses F11- F16 and the module (3) of those fuses, then
attach the fuse box on the back of the access little door (1).
Carefully mount the fuse box access little door, then close it.
Connect the (-) battery plug.
Perform functional tests, noticing the correct operation of all consumers supplied by means of
the cockpit fuse box.
OBSERVAT ION
For vehicle equipped with radio-tape player, after battery reconnecting, the radio
code must be introduced, in order to make it again running.
1
4
vnx.su