oil DACIA SUPERNOVA 2004 Service Manual

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 56
DIAG
NOSING-INTERPRETING THE STATES
STATEIDLE MODE ADJUSTMENT
SUGGESTIONS There shou
ld be no defect present or memorized
Check the resistance of the step-by-step engine for the idle mode adjustment.
Change it if necessary.
Check the insulation and the continuity of the cabling along the circuits:
- pin 12 calc ulator ♦ pin B step-by-step engine
- pin 41 calc ulator ♦ pin A step-by-step engine
- pin 42 calc ulator ♦ pin C step-by-step engine
- pin 72 calc ulator ♦ pin D step-by-step engine
Remedy if necessary, and then go on with the diagnose, watching the tolerance value of
the idle mode rotation ratio.
The id le mode rotation
ra tio< minimal limit. The id le mode rotation ratio is too small.
-Check th e functioning of the enrichment adjustment.
-Clean the air supply circuit (clapper body, step-by-step engine) as they seem to be dirty.
-Ch eck th e oil level of the engine (too high a level causes splash lubrication)
-Ch eck the pressure of petrol (see if it is not too small)
-Ch eck en gine compression with the “CLIP TEHNIC” tester
-Ch eck the adjustment of the rocker-arms and the settling of the distribution.
-Ch eck the ignition system
-Ch eck the in jectors.
If all the above are correct, then the step-by-step engine will have to be replaced.
AFTER REPAIRPerform again the conformity test.
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 57
DIAG
NOSING-INTERPRETING THE STATES
The idle mode rotation
ra tio > maximal limit. The id
le mode rotation ratio is too great.
- Chec k the oil level of the engine
- Chec k the good functioning of the atmospheric pressure sensor.
- Check the tubes connected to the admission collector.
-C heck the fittings of the admission collector
- Check the watertightness fittings of the clapper body
- Check the watertightness of the power-brakes.
- Chec k the presence of the nozzles of the oil-vapour re-aspiration circuit
- Chec k petrol pressure.
- Check the adjustment of the rocker-arms and the settling of the distribution.
If all the above are correct, then the step-by-step engine will have to be replaced.
Perform again the conformity test
AF T E R REPAIR
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 66
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
STARTING PROBLEMS
1.
Do not use this information before having done the complete check-up
with the tester!
SUGGESTIONS
♦♦
♦♦
Check if there is petrol in the fuel tank (do not rely on the
on-board in
dices). Check if it is the fuel recommended by
the manufacturer.
Disconnect the tube between the draining valve and the
intake collector and strangle it up. If the disturbances disap-
pear, the cause was the draining valve.
Connect the “CLIP TEHNIC” device to do this test in ac-
cordance with the usual manner of work.
Connect the tester “CLIP” and do the test corresponding to
the check-up of the rotation signal.
Gently touch the step-by-step engine in order to possibly
unbloc k it.
Check the fuel
Check the canister
draining valve♦♦♦♦
Check the engine
co
mp ression
Check the
engine flywheel
Check the step-by-
step engine
♦♦ ♦♦
♦
♦
Check if there are no broken tubes.
Check the state of the sparking plugs and the ignition coil.
Check the tubes and
hoses
♦♦♦♦
Check the ignition♦♦♦♦
Check the flow and the pressure of the fuel: the condition
of
the petrol-pump, of the pressure regulator. Check the
injectors (flow, shape of jet)
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.
Check the fuel-
supply circuit
♦♦♦♦
Check the exhaust
system
♦♦♦♦
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 67
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
IDLE MODE PROBLEMS
Do not use this information before having done the complete check-
up w ith the tester!2.
SUGGESTIONS
Check if there is petrol in the fuel tank (do not rely on the
on-board indi ces). Check if it is the fuel recommended by
the manufa cturer.
Check the fuel

Check if there are no broken tubes.
Check the tubes and hose
s.
♦
♦
Check the state of the sparking plugs and the ignition coil.
Check, on the o il ga uge , if the le ve l of the oil is not too h igh.
Connect the tester “CLIP” and do the test corresponding
to the check-up of the rotation signal.
Gently touch the step-by-step engine in order to possibly
unblock it.
Check the condition of the fittings.
Check, after taking them apart, whether the injectors leak.
Check if the clapper body is not clogged.
Check the ignition
Check the engine oil level
Ch eck the step-by-step engine
Check the intake collector
Check the injectors
Ch eck the body of the clapper
♦
♦
Check the engine flywheel♦
♦
♦
♦
♦
Check the flow and the pressure of the fuel: the condition
of the pe trol-pump, of the pressure regulator. Check the
injectors (flow, shape of jet)
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.
Check the fuel-supply
circuit
Check the exhaust system
♦
♦
A
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 69
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
RUNNING PROBLEMS3.
SUGGESTIONSDo not use this information before having done the complete
check- up with the tester!
Check if there are no broken tubes
Check if the air filter is not deformed.
Check the condition of the fittings.
Check if the exhaust collector is watertight.
Make sure that, after taking them off, the injectors do not leak.
♦
♦
♦
Check if there are no broken tubes
Check the state of the sparking plugs and the ignition coil.
Check if there is petrol in the fuel tank (do not rely on the
on-board in dices). Check if it is the fuel recommended by
the manufa cturer. Check if there are no broken tubes.
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.Check the exhaust
system
♦♦
♦ ♦
♦ ♦ ♦Check, on the oil gauge, if the level of the oil is not too high.
Check the air filter
Ch eck the fuel
Check the tube s a nd
hose s.
Check the fuel-sup-
ply circuit
Check the ignition Check the engine oil
levelCheck the intake
collector
Check the exhaust
collector
Check the injectors
A
vnx.su

20
CLUTCH
The complete return
of the clut ch pedal is
checked
The state of the
hydrau lic circuit is
checked
The worn-out or oiled
clutch is checked
- The worn-out elements are
replaced
- The cause of the leakage is
e liminated.
The st at e of the
pedal is checked


The state of the clutch
m echanism is checked,
and it is replaced if
nece ssary


Clutch skidding
The engine has the ten-
dency to accelerate
NECONFORMING
NON-CONFORMING
The faulty parts are
replaced
CONFORMING
CONFORMING
CONFORMING
D I A G N O STIC
20 - 5


vnx.su

20
CLUTCH
Trepidation
(t he car starts “by fits”)
The sta te of the props
of the gearbox is checked
Oiled clutch, or clutch hav-
ing a beat
The fau lty parts are replaced.
The o rigin of the beat is elimi-
nated.
The pr ops are replaced and the tight-
ening of the gearbox fixing spots on
the engine is checked, and also the
fixing of the engine
Clutch pedal has a “creak”
The axis of the clutch
pedal is oiled
Pedal axis worn-out
The fau lty parts are replaced
NON-CONFORMING



NON-
CONFORMING

CONFORMING



D I A G N O STIC
20 - 8
vnx.su

CV JH3 - 05021
MANUAL GEARBOX
21 - 3
TIGHTENING MOMENTS
DESCRIPTION
A
ttachment screws of the mechanism crankcase on the clutch –
di fferential case
S econdary shaft screw
Primary shaft nut
Back cap fixing screws
Oil draining plug
R everse driving contact
S crews for fixing the bellows – left transmission cap assembly
Screws for fixing gearbox on engine case (M10 – 90)
Screws for fixing gearbox on engine case (M10 – 35)
S crews for fixing gearbox on engine
LOCTOU fixing screw
Screws for fixing the RPM sensor on the clutch c ase
S crews for fixing the control axle assembly
S crews for fixing hydraulic receiver on clutch case MOMENT
(daNm)
2,57
19
2,5
2,5
2,5
2,5
4,4
2,1
4,4
0,5
0,8 2
2,1
vnx.su

CV JH3 - 05021
MANUAL GEARBOX
21 - 5
CAPACITY , LUBRICANTS
Oil used : 75 W – 80 W; API GL5.
The qu antity of oil needed for the gearbox operation is 3. 5 liters .
Th e oiling of the gearbox parts is done by splash lubrication.
Checking of the oil level is done through the filling plug A.
CAPACITY , LUBRICANTS
vnx.su

CV JH3 - 05021
MANUAL GEARBOX
21 - 8
PA
RTS OF SYSTEMATIC REPLACEMENT
The following parts shall be replaced, if they have been dismounted: - oil seal rings;
- fastening rings;
- elastic pins;
- primary shaft nut
- the bushing under the pinion of the 5 – th step;
- the outer safety devices of the bearings of the primary and the secondary shafts;
- the ga skets. PA
RTS OF SYSTEMATIC REPLACEMENT
vnx.su