Rod DAEWOO LACETTI 2004 Service Repair Manual

5B – 26IFIVE–SPEED MANUAL TRANSAXLE
DAEWOO V–121 BL4
UNIT REPAIR
MAJOR COMPONENT DISASSEMBLY
Tools Required
J–6125–B Slide Hammer
J–22888–20–A BearingPuller with J–22888–35 Puller
Legs
KM–553–A Fifth Gear Puller
J–36633 Snap Ring Retainer
KM–113–2 Base
J–42469 Shift Rod Remover
KM–552 Fixture
Disassembly Procedure
1. Remove the transaxle from the vehicle. Refer to
”Transaxle Assembly” in this section.
2. Remove the filler plug at the cover.
3. Remove the bolts from the gearshift lever cover.
4. Remove the gearshift lever cover.

FIVE–SPEED MANUAL TRANSAXLE 5B – 27
DAEWOO V–121 BL4
5. Bolt the gearshift lever cover to the fixture KM–552.
6. Position the fixture KM–552 into the base
KM–113–2.
7. Remove the snap ring, the bushing, the spring, and
the intermediate lever.
8. Remove the shift finger lever pin.
9. Remove the gearshift rod and the shift finger lever.

FIVE–SPEED MANUAL TRANSAXLE 5B – 31
DAEWOO V–121 BL4
24. Remove the input drive fifth–gear snap ring.
25. Remove the input drive fifth gear using the fifth–
gear puller KM–553–A.
26. Remove the bolts and the fifth–gearshift connector
from the bearing plate using the pawl.
27. Remove the four shift–rod plugs using the shift rod
remover J–42469 and the slide hammer J–6125–B.

5B – 32IFIVE–SPEED MANUAL TRANSAXLE
DAEWOO V–121 BL4
28. Remove the spring and the rod lock pin from the
small plug hole.
29. Remove the pin from the reverse gearshift rod/fork
assembly.
30. Remove the reverse gearshift rod/fork assembly
from the bearing plate.
31. Remove the bolts from the support bracket.

FIVE–SPEED MANUAL TRANSAXLE 5B – 33
DAEWOO V–121 BL4
32. Remove the first–second gearshift fork holding pin.
33. Drive the first–second gearshift rod out until it is just
free of the bearing plate.
34. Remove the support bracket from the bearing plate.
35. Remove the third–fourth gearshift fork holding pin
and the third–fourth gearshift rod.

5B – 34IFIVE–SPEED MANUAL TRANSAXLE
DAEWOO V–121 BL4
36. Remove the fifth gearshift lever from the bearing
plate.
37. Remove the first–second gearshift rod.
38. Compress the snap ring holding the mainshaft and
secure it with the snap ring retainer J–36633.
39. Hold the snap ring open at the base of the input
shaft using the snap ring pliers.
40. Remove the mainshaft assembly and the input
shaft assembly from the bearing plate.

FIVE–SPEED MANUAL TRANSAXLE 5B – 57
DAEWOO V–121 BL4
8. Install the third–fourth gearshift rod/fork holding pin.
9. Install the support bracket onto the bearing plate.
10. Install the first–second gearshift rod/fork onto the
bearing plate.
11. Install the first–second gearshift fork holding pin.

5B – 58IFIVE–SPEED MANUAL TRANSAXLE
DAEWOO V–121 BL4
12. Install the support bracket bolts.
Tighten
Tighten the support bracket bolts to 7 NSm (62 lb–in).
13. Install the reverse gearshift rod/fork onto the bear-
ing plate.
14. Install the reverse gearshift rod/fork holding pin.
15. Install the rod lock pin and spring into the small plug
hole.

FIVE–SPEED MANUAL TRANSAXLE 5B – 59
DAEWOO V–121 BL4
16. Install the fourth–gearshift rod plugs.
17. Install the bolts and the fifth–gearshift connector
onto the bearing plate, using the pawl.
Tighten
Tighten the fifth–gearshift connector bolts to 7 NSm
(62 lb–in).
18. Install the input drive fifth gear using the installer
KM–554 and the installer sleeve KM–334.
19. Install the snap rings securing the fifth–drive gear.

5B – 62IFIVE–SPEED MANUAL TRANSAXLE
DAEWOO V–121 BL4
31. Bolt the gearshift lever cover to the fixture KM–552.
32. Position the fixture into the base KM–113–2.
33. Install the gearshift rod, the shift finger lever, and
the gearshift lever pin.
34. Install the snap ring, the bushing, the spring, and
the intermediate lever.
35. Remove the gearshift lever cover from the base
KM–113–2 and the fixture KM–552.
36. Shift the transaxle into NEUTRAL.
37. Install the gearshift lever cover and the gearshift
lever cover bolts.
Tighten
Tighten the gearshift lever cover bolts to 22 NSm (16
lb–ft).
38. Install the transaxle cover and the transaxle cover
bolts.
Tighten
Tighten the transaxle cover bolts to 18 NSm (13 lb–ft).
39. Install the transaxle into the vehicle. Refer to
”Transaxle Assembly” in this section.