Reverse DAEWOO LACETTI 2004 Service Owner's Guide

AISIN AUTOMATIC TRANSAXLE 5A2 – 3
DAEWOO V–121 BL4
SPECIFICATIONS
GENERAL SPECIFICATIONS
Definition
1.6 DOHC
Transaxle Fluid TypeISU DEXRON III or ESSO JWS 3309
Transaxle Fluid Capacity5.77L (6.1 qts)
TRANSAXLE GEAR RATIO
GearRatio
1.6 DOHC
First2.875
Second1.568
Third1.000
Fourth0.697
Reverse2.300
Counter1.020
Differential3.750
FLUID CAPACITY
Capacity
1.6 DOHC
Transaxle Fluid (dry fill)5.77L (6.1 qts)
Transaxle Fluid (drain and refill)2.1L (2.2 qts)
Notice : Fluid capacity (drain and refill) could be changed according to the some condition, therefore be sure to check
the fluid using the oil stick guage.
LINE PRESSURE SPECIFICATION
ApplicationIdlingStall
At ”D” range3.9–4.2 kg/cm2 (55–60 psi)11.3–12.5 kg/cm2 (161–178 psi)
At ”R” range6.0–6.9 kg/cm2 (85–98 psi)16.2–18.6 kg/cm2 (230–265 psi)

AISIN AUTOMATIC TRANSAXLE 5A2 – 5
DAEWOO V–121 BL4
SPECIAL TOOLS
SPECIAL TOOLS TABLE
DW260–021–02
Automatic
Transaxle
Overhaul
Fixture
DW240–020
Brake/Clutch
Spring Compressor
DW240–030
Forward Clutch
Adapter
DW240–040
Direct Clutch
Adapter
DW240–050
Overdrive
Brake Adapter
DW240–060–01
Brake Spring
Compressor
Bolt/Nut
DW240–060–02
Brake Spring
Compressor
Plate
DW240–070
1st/Reverse
Brake Adapter

5A2 – 22IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
1. Planetary Ring Gear
2. O–ring
3. 1st and Reverse Brake Piston
4. O–ring
5. 1st and Reverse Brake Piston Return Spring
6. Plate
7. Disc
8. Flange
9. Snap Ring
10. Planetary Gear
11. Thrust Washer
12. No. 2 One–Way Clutch
13. Anti–Rattle Clip
14. Flange
15. Disc
16. Plate
17. 2nd Brake Piston Return Spring
18. O–ring
19. 2nd Brake Piston
20. O–ring
21. 2nd Brake Clutch Cylinder
22. Snap Ring
23. Thrust Bearing Race
24. Front Planetary Sun Gear
25. Thrust Bearing Race26. One–Way Clutch Assembly
27. Thrust Washer
28. Rear Planetary Sun Gear
29. Snap Ring
30. Flange
31. Disc
32. Plate
33. Thrust Bearing Race
34. Thrust Needle Roller Bearing
35. Forward Clutch Hub
36. Thrust Bearing Race
37. Thrust Needle Roller Bearing
38. Thrust Bearing Race
39. Forward and Reverse Clutch Assembly
40. Thrust Needle Roller Bearing
41. Snap Ring
42. O/D Brake Return Spring
43. O/D Brake Piston
44. O–ring
45. Seal Ring
46. Transaxle Rear Cover
47. Apply Gasket
48. O–ring
49. Screw Plug

5A2 – 28IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
FUNCTION CHECK
Confirm whether below condition before function check.
S Oil temperature is hot condition (50°C (122°F) ~
80°C (176°F)).
S Switch of A/C and light etc are off.
Stall Test
Stall test’ purpose is to inspect overall performance of A/T
and engine by measuring the stall speed in ”D” and ”R”
range.1. Chock 4 Wheels and apply parking brake fully, lock
vehicle perfectly.
2. Fully pressed on foot brake pedal with left foot.
3. Shift into ”D” and ”R” range, fully press on accelera-
tor pedal with right foot.
Quickly read stall speed at this time.
Standards
2390 ± 150 rpm
Notice : Do not continuously run longer than 5 sec be-
cause of extreme increasing oil temp.
Make sure to keep interval for more than 1 min between
stall tests.
Result of Stall Test
Cause of Failure
Lower than standards
both ”D” and ”R”Less engine power
Torque converter one way clutch failure
Higher than standards
only ”D”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Forward clutch (C1) failure (Slipping)
No.2 One–way clutch (F2) failure
Higher than standards
only ”R”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Reverse clutch (C3) failure (Slipping)
1st & reverse brake (B3) failure (Slipping)
Higher than standards
both ”D” and ”R”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Oil pump failure
Oil strainer failure (clogging)
Oil leak for each range circuit
Time Lag Test
Time lag is time till slightly shock can be felt when shift le-
ver is shifted ”N”  ”D” and ”N”  ”R” while engine idling.
Time lag test can inspect hydraulic condition and clutch/
brake condition.
1. Chock 4 Wheels and apply parking brake fully, lock
vehicle perfectly.
2. Measure time lag by using stop watch from moment
when shift lever is shifted in ”N”  ”D” and ”N” 
”R” until moment slightly shock can be felt.”N  D”less than 0.7 sec
”N”  ”R”less than 1.2 sec
Notice : Make sure to take 3 measurement and take the
average value.
Make sure to keep interval for more than 1 min between
time lag tests. (That purpose is to remove clutch/brake
pressure was left unfinished.)

AISIN AUTOMATIC TRANSAXLE 5A2 – 29
DAEWOO V–121 BL4
Result of Time Lag TestCause of Failure
Longer than standards ”N”  ”D”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Forward Clutch (C1) failure (Slipping)
Timing solenoid failure
Oil leak for ”D” range circuit
Longer than standards ”N”  ”R”Lower line pressure
S Pressure control solenoid (PCS) failure
S Primary regulator valve failure
Reverse clutch (C3) failure (slipping)
1st & reverse brake (B3) failure (slipping)
Oil leak for ”R” range circuit
Hydraulic Test
Hydraulic test can inspect working condition inside A/T by
measuring line pressure in ”D” / ”R” range and ”idle” / ”stall”
condition.
1. Chock 4 Wheels and apply parking brake fully, lock
vehicle perfectly.2. Install oil pressure gage adapter DW240–010–02 to
test hole for line pressure.
3. Fully pressed on foot brake pedal with left foot, shift
into ”D” and ”R” range and measure line pressure
”idle” / ”stall” condition.
Line pressure
Mpa (kgf/cm
2)
DR
Engine idle0.37 (3.9)
–0.14 (4.2)0.59 (6.0)
–0.68 (6.9)
Engine stall1.10 (11.3)
–1.23 (12.5)1.58 (16.2)
–1.83 (18.6)
Notice : Do not continuously run longer than 5 sec be-
cause of extreme increasing oil temp.
Make sure to keep interval for more than 1 min between
stall tests.
Make sure to check no oil leak after installing oil pressure
gage adapter.
Result of Hydraulic Test
Cause of Failure
Higher than standards
both ”D and ”R”Pressure control solenoid (PCS) failure
Primary regulator valve failure
Lower than standards
both ”D and ”R”Pressure control solenoid (PCS) failure
Primary regulator valve failure
Oil pump failure
Oil strainer failure (clogging)
Oil leak for each range circuit
Lower than standards
only ”D”D” hydraulic circuit failure
Forward clutch (C1) failure
Lower than standards
only ”R””R” hydraulic circuit failure
Reverse clutch (C3) failure
1st and reverse brake (B3) failure

5A2 – 30IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
Manual Shifting Test
Manual shifting test is to determine whether failure symp-
tom is within electrical failure or mechanical failure.
1. Disconnect wire harness of shift solenoid, check
the range and gear positions correspond with below
table when driving by manual shifting.
Range
Gear
D3rd gear
RReverse
Notice : Make sure to disconnect only wire harness of shift
solenoid.
UNIT INSPECTION
Drive Plate Deflection
S Inspect drive plate deflection if within standard
value.
Standard Value
within 0.2mm (0.008 in)
Action :
Standard value is not within the specified value, replace
drive plate.
When ”abnormal wear” or ”stick” on torque converter
sleeve or oil pump is found, replace torque converter and
A/T.
Notice :
S When assembling torque converter and drive plate.
Be sure to use correct bolt with correct length. The
bolt pushes up torque converter front cover, and it
damages lock–up clutch lining. As a result, it cause
major failure ”No move”.
S Do not tighten the bolts by using impact wrench.
Cooler Pipe Bending and Choke
S Inspect it whether there is abnormal pipe bending in
the cooler pipe, pipe deformation and small cross–
section area of pipe line.
Action : Replace failure parts.S Apply compressed air of 2kg/cm
2 from cooler pipe
inlet side, inspect whether there is not cooler pipe
choke by confirming air flow smooth.
Action : Remove foreign particles and clean inside of pipe
line.
Normal
Vehicle Speed Sensor
1. Remove the connector of vehicle speed sensor,
connect 12V power supply and voltmeter to the ter-
minal.(Do not mistake polarity)
2. Check voltage change from approx. 0V to 12V with
vehicle speed sensor driven gear rotated.
Notice : The voltage change should be 4 times for 1 revo-
lution of the vehicle speed sensor driven gear.
Action : If the result of inspection is bad, replace the ve-
hicle speed sensor.

AISIN AUTOMATIC TRANSAXLE 5A2 – 47
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0705
TRANSMISSION RANGE (TR) SWITCH CIRCUIT
MALFUNCTION
Conditions for Setting the DTC
S TCM detects more than two equal signals from the
Park/Neutral Position switch circuit for 10 seconds
continuously.
S TCM detects the no signal of TR switch circuit for 2
seconds continuously.
S Vehicle speed is 30 km/h (19 mph) or greater.
S Engine revolution is 1500 rpm or greater.
Action Taken When the DTC Sets
S TCM will request the illumination of MIL and store
DTC when TCM detects failures on two consecu-
tive ignition cycle.
S TCM judges with the priority. (D>2>1>R>N>P)
S No timing solenoid control for N–D
S No self–learning control
S No lockupS No prevent reverse gear control
Conditions for Clearing the DTC
S The TCM turns off the MIL when no further failures
detected for three consecutive ignition cycles.
S The scan tool can clear the DTC from the TCM his-
tory.
S The TCM clears the DTC from the TCM history
memory after forty consecutive warm up cycles
without fault.
S TCM detects single ”D range” signal of the TR
switch.
Cause of Failure
S Wiring harness or connector between TR switch
and TCM
S TR switch
S TCM

AISIN AUTOMATIC TRANSAXLE 5A2 – 59
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0722
OUPUT SHAFT SPEED (OSS) SENSOR CIRCUIT NO
SIGNAL
Conditions for Setting the DTC
S This DTC detects no signal of Output Shaft Speed
(OSS) sensor circuit for a long period of time. (
Revolution : 0 rpm
10000 rpm).
S TCM detects no pulse of Output Shaft Speed
(OSS) sensor while TCM detects 178 pulses of In-
put Shaft Speed sensor. This detection 500 times
continuously.
S D,2,L range selected
S Input speed is 5 km/h (3 mph) or greater.
S DTCs P0751, P0753, P0756, P0758, P0717 and
P0705 are not set.
S 25 seconds later after Neutral to Drive shift.
Action Taken When the DTC Sets
S TCM will request the illumination of MIL and store
DTC when TCM detects a failure on the first ignition
cycle.
S No lockup control
S No engine torque reduction control
S No engagement pressure controlS No 4th gear
S No self–learning control
S No prevent reverse gear control
Conditions for Clearing the DTC
S The TCM turns off the MIL when no further failures
detected for three consecutive ignition cycles.
S The scan tool can clear the DTC from the TCM his-
tory.
S The TCM clears the DTC from the TCM history
memory after forty consecutive warm up cycles
without fault.
S TCM detects 250 pulses of Output Shaft Speed
(OSS) sensor while failure detection is not
achieved.
Cause of Failure
S Wiring harness or connector between Output Shaft
Speed (OSS) sensor and TCM
S OSS sensor
S TCM

AISIN AUTOMATIC TRANSAXLE 5A2 – 117
DAEWOO V–121 BL4
UNIT REPAIR
MAJOR COMPONENT DISASSEMBLY
Tools Required
DW240–020 Brake/Clutch Spring Compressor
DW240–050 Overdrive Brake Adapter
DW240–060–01 Brake Spring Compressor Bolt/Nut
DW240–070 1st & Reverse Brake Adapter
DW240–080 2nd Brake Adapter
DW240–090 Planetary Ring Gear Remover
DW240–150 Transaxle Case Side Bearing Outer Race
Adapter
DW240–170 Adapter Handle
DW260–021–02 Automatic Transaxle Overhaul Fixture
(81–40 LE)
DW260–041 Planetary Ring Gear Nut Removal/Installa-
tion Socket
Disassembly Procedure
1. Remove the transaxle assembly from the vehicle.
Refer to”Transaxle Assembly” in this section.
2. Install the transaxle assembly to the transaxle sup-
port stand using Automatic Transaxle Overhaul Fix-
ture DW260–021–02 (81–40 LE).
3. Remove the nut, washer and control lever.
4. Using a screwdriver, unstake the lock washer.
5. Remove the two bolts and nut and pull out the
transmission range (TR) switch.
6. Remove the two unions the transaxle case.
7. Remove the two O–rings from the unions.

5A2 – 126IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
48. Remove the thrust needle roller bearing and for-
ward & reverse clutch assembly.
49. Remove the thrust needle roller bearing and thrust
bearing race from the forward & reverse clutch as-
sembly.
50. Remove the forward clutch hub from the transaxle
case.
51. Remove the thrust bearing race and thrust neddle
roller bearing from the forward clutch hub.