heater DAEWOO MATIZ 2003 Service Owner's Manual

7A–12 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
Improper Air Delivery or No Mode Shift (Cont’d)
Step Action Value(s) Yes No

8


Repair the cable attachment or control as necessary.
Is the repair complete?
–

System OK

Go to Step 9

9


Recheck the system using the “Control
Settings/Correct Results” tests in this procedure.
Is the repair complete?
–

System OK

Go to Step 10



10




Check for airflow from the defroster or the vent
outlets.
Is there high airflow from the defroster or the vent
outlets?



–



Go to Step 11



Go to Step 12

11


Adjust the heater door at the floor and the vent door
to get the proper airflow.
Is the repair complete?
–

System OK

–

12

Switch the mode knob to defrost.
Is the defroster airflow OK?
–

Go to Step 13

Go to Step 14




13




1. Remove the heater outlet.
2. Check the heater outlet for obstructions.
3. Remove any obstructions in the heater outlet.
Is the repair complete?



–



System OK




–

14

Check the blower speeds for change in the airflow.
Does the blower speed increase as the control is
turned from 1 to 4?
–
Go to Step 15

Go to ‘‘Blower
Electrical’’


15



1. Check for obstructions in the system at the
blower inlet.
2. Remove any obstructions at the blower inlet.
Is the repair complete?

–


System OK



Go to Step 16




16





1. Set the blower on 4.
2. Rotate the temperature control from full hot to full
cold.
3. Listen for an airflow change.
Did the airflow change?





–




Go to Step 17




Go to Step 18



17



1. Check the temperature door adjustment, the
cables, the linkage, and the control.
2. Adjust the temperature control to full hot.
Is the repair complete?


–


System OK



–




18




1. Check the system for any obstruction between
the blower and the system outlets.
2. Remove any obstruction between the blower and
the system outlets.
Is the repair complete?



–



System OK




–

HEATING AND VENTILATION SYSTEM 7A–13
DAEWOO M-150 BL2
TOO MUCH HEAT
Step Action Value(s) Yes No

1

Verify the customer’s complaint.
Are the customer’s concerns verified?
–
Go to Step 2

System OK

2


Set the mode switch to the floor position.
Is there too much heat when the mode switch is in
the floor position?
–

Go to Step 3

Go to Step 9
3

Check for defroster bleed.
Is there objectionable defroster bleed?
–

Go to Step 4

Go to Step 5



4




1. Check the door travel, the cables, the controls,
and the linkage for the heater and the defroster.
2. Adjust or repair, as required.
Is the repair complete?



–



System OK




–







5







1. In vehicles equipped with A/C, set the A/C switch
OFF.
2. In all vehicles, set the blower speed to 4.
3. Set the temperature to full hot.
4. Turn the ignition switch to ON.
5. Check for airflow from the floor outlets.
6. Check the floor outlet attachment.
Is the airflow high?







–






Go to Step 7






Go to Step 8



6




Check for a change in the airflow at different blower
speeds.
Does the airflow change as the setting for the
blower-speed switch is changed?



–



System OK




Go to ‘‘Blower
Electrical’’




7




1. Check the temperature door travel, the cables,
and the linkage.
2. Adjust to full cold.
3. Check for full hot.
Is the repair complete?



–



System OK




–

8


Adjust or repair the floor/defroster and/or the vent/
floor mode.
Is the repair complete?
–

System OK

–


9



Set the mode switch to the vent position.
In the vent position, is the problem objectionable
bleed?

–


Go to Step 10


Go to Step 15



10



1. Check the system case for leaks.
2. Check the floor outlet attachment.
Are any problems found?


–


Go to Step 11


Go to Step 12

11

Repair the system case or the floor outlet attach-
ment as required.
Is the repair complete?
–
System OK

Go to Step 12




12




1. Turn the ignition switch OFF.
2. Turn the temperature control knob to full hot, then
rapidly to full cold.
Do you hear the door slam just before you reached
the end of the control travel?



–



Go to Step 13



Go to Step 14
13

Adjust the vent door to vent more.
Is the repair complete?
–

System OK

–

7A – 18 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON-VEHICLE SERVICE
D108A502
D108A501
CONTROL ASSEMBLY AND
CONTROL CABLES
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster housing trim panel.
Refer to Section 9E, Instrumentation/Driver informa-
tion.
3. Remove the control assembly.

Remove the control assembly retaining screws (1).

Separate the control assembly from the instrument
panel (2).

Disconnect the electrical connectors (3).

Disconnect the mode control cable from the heater
module (4).

Disconnect the temperature control cable from the
heater module (5).

Remove the glove box from the instrument panel.
Refer to Section 9E, Instrumentation/Driver Infor-
mation.
D108A503

Disconnect the recirculating/fresh air door cable
from the blower module (6).

HEATING AND VENTILATION SYSTEM 7A–19
DAEWOO M-150 BL2
D108A504
D108A505
4. Disconnect the control cables from the control as-
sembly.

Disconnect the temperature control cable (1).

Disconnect the mode control cable (2).

Disconnect the recirculating/fresh air door cable
(3).
D108A506
Installation Procedure
1. Connect the control cables to the control assembly.
2. Connect the recirculating/fresh air door cable to the
blower module.
3. Install the glove box to the instrument panel. Refer to
Section 9E, Instrumentation/Driver Information.
4. Connect the temperature control cable and the mode
control cable to the heater module.
5. Connect the electrical connectors.
6. Install the control assembly with the screws.
7. Install the instrument cluster housing trim panel. Re-
fer to Section 9E, Instrumentation/Driver Information.
8. Connect the negative battery cable.

7A–22 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
D18A515A
HEATER HOSES
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Tool Required
DW100–020 Hose Remover/Installer.
Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the coolant.
3. Remove the heater inlet hoses.

Remove the air cleaner housing.

Raise and suitably support the vehicle.

Disconnect the hose from the heater module using
a hose remover DW100–020 (1).
D108A516

Lower the vehicle.

Disconnect the hose from the thermostat (2).
D18A517A
4. Remove the heater outlet hoses.

Raise and suitably support the vehicle.

Disconnect the hose from the heater module using
a hose remover DW100–020 (1).

Disconnect the B
+ terminal from the starter. Refer
to Section 1E, Engine Electrical.
D108A518

Disconnect the heater hose from the engine (2).

HEATING AND VENTILATION SYSTEM 7A–23
DAEWOO M-150 BL2
D108A521
Installation Procedure
1. Install the heater outlet hoses.

Connect the heater hose to the engine (1).

Connect the B
+ terminal to the starter. Refer to
Section 1E, Engine Electrical.
D18A522A

Connect the hose to the heater module using a
hose installer DW100–020 (2).

Lower the vehicle.
D108A519
2. Install the heater inlet hoses.

Connect the hose to the thermostat (1).

Raise and suitably support the vehicle.
DW100–020
D18A520A

Connect the hose to the heater module using a
hose installer DW100–020 (2).

Lower the vehicle.

Install the air cleaner housing.
3. Refill the coolant. Refer to Section 1D, Engine Cool-
ing.
4. Connect the negative battery cable.

7A–24 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
D108A523
HEATER MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the heater hoses from the heater module.
Refer to “Heater Hoses” in this section.
2. Remove the instrument panel and the lower tie bar
center. Refer to Section 9E, Instrumentation/Driver
Information.
3. Remove the heater module–to–blower module con-
nection tube on the vehicle not equipped with A/C.
a. Heater module–to–blower module connection tube.
D108A524
4. Remove the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
D108A525
5. Remove the heater module.

Remove the upper nuts (1).
D108A526

Remove the lower nuts (2).

Remove the heater module (3).

HEATING AND VENTILATION SYSTEM 7A–25
DAEWOO M-150 BL2
D18A527B
D18A528B
Installation Procedure
1. Install the heater module with the nuts.
Tighten
Tighten the heater module lower nuts to 3–5 Nm
(27–44 lb-in) (1).
Tighten the heater module upper nuts to 3–5 Nm
(27–44 lb-in) (2).
2. Install the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
3. Install the heater module–to–blower module connec-
tion tube on the vehicle not equipped with A/C with
the screw.
4. Install the instrument panel and the lower tie bar. Re-
fer to Section 9E, Instrumentation/Driver Information.
5. Connect the heater hoses to the heater module. Re-
fer to “Heater Hoses” in this section.
D108A529
D108A530
BLOWER MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the glove box from the instrument panel. Re-
fer to Section 9E, Instrumentation/Driver Information.
2. Remove the heater module–to–blower module con-
nection tube on the vehicle not equipped with A/C.
Refer to “Heater Module” in this section.
3. Remove the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
4. Remove the blower resistor. Refer to “Blower Resis-
tor” in this section.
5. Disconnect the blower motor connector. Refer to
“Blower Motor and Cooling Hose” in this section.
6. Remove the blower module.

Remove the nuts (1).

Disconnect the wiring harness (2).

7A–26 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
D18A531B
Installation Procedure
1. Install the blower module with the nuts.
Tighten
Tighten the blower module retaining nuts to 3–5 Nm
(27–44 lb-in).
2. Connect the wiring harness.
3. Connect the blower motor connector. Refer to “Blow-
er Motor and Cooling Hose” in this section.
4. Install the blower resistor. Refer to “Blower Resistor”
in this section.
5. Install the evaporator on the vehicle equipped with
A/C. Refer to Section 7B, Manual Control Heating,
Ventilation, and Air Conditioning System.
6. Install the heater module–to–blower module connec-
tion tube on the vehicle not equipped with A/C. Refer
to “Heater Module” in this section.
7. Install the glove box to the instrument panel. Refer to
Section 9E, Instrumentation/Driver Information.
D108A532
DEFROSTER DUCT AND HOSES
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the instrument panel. Refer to Section 9E,
Instrumentation/Driver Information.
2. Remove the defroster duct and hoses retaining
screws.
a. Retaining screw.
3. Remove the defroster duct and hoses.
b. Defroster duct and hoses.
D108A533
Installation Procedure
1. Install the defroster duct and hoses with the screws.
2. Install the instrument panel. Refer to Section 9E, In-
strumentation/Driver Information.

7A–28 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
UNIT REPAIR
D108A701
HEATER CORE
Disassembly Procedure
1. Remove the heater module. Refer to “Heater Module”
in this section.
2. Remove the heater core.

Remove the heater core cover (1).

Remove the heater core (2).
D108A702
Assembly Procedure
1. Install the heater core to the heater module.
2. Install the heater core cover.
3. Install the heater module. Refer to “Heater Module” in
this section.