clock DAEWOO NUBIRA 2004 Service Owner's Guide

5A2 – 102IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
3. Remove the E–ring.
4. Disconnect the shift control cable from the TR
switch lever.
5. Remove the retaining nut and then remove the
washer and the control lever.
6. Using a driver, unstake the lock washer and re-
move the nut.
Installation Procedure
1. Install the Transmission Range (TR) switch onto the
manual valve lever shaft and temporarily install the
2 adjusting bolts.
2. Install the new lock washer and nuts.
Tighten
Tighten the nuts to 12 NSm (106 Ib–in).
3. Temporarily install the control lever.
4. Turn the lever counterclockwise until it stops, then
turn it clockwise 2 notches.
5. Remove the control lever.

5A2 – 150IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
59. Check that the planetary gear turns freely counter-
clockwise and locks clockwise.
60. Install the anti–rattle clip in the place shown in the
illustration (the space between the No.2 one–way
clutch outer race and transaxle case), push the
anti–rattle clip in until you hear the ”click”.
61. Using vernier calipers, measure the free length of
the 2nd brake piston return spring together with
spring seat.
S Standard free length: 15.85 mm (0.6240 in.).
62. Check to see if the sliding surface of the disc, plate
and flange of 2nd brake are worn or burnt. If neces-
sary, replace them.
Notice : If the lining of the disc is peeling off or discolored,
or even if a part of the groove is defaced, replace all discs.
Notice : Before assembling new discs, soak them in ATF
for at least 15 minutes.

AISIN AUTOMATIC TRANSAXLE 5A2 – 165
DAEWOO V–121 BL4
132. Temporarily install the control lever.
133. Turn the lever counterclockwise until it stops,
then turn it clockwise 2 notches.
134. Remove the control lever.
135. Align the groove with neutral basic line.
136. Tighten the 2 bolts.
Tighten
Tighten the bolts to 5.4 NSm (48 lb–in).
137. Using a screwdriver, stake the nut with the lock
washer.

AISIN AUTOMATIC TRANSAXLE 5A2 – 181
DAEWOO V–121 BL4
Disassembly Procedure
1. Install the one–way clutch and thrust washer to the
rear planetary sun gear.
2. Hold the rear planetary sun gear and turn the one–
way clutch. The one–way clutch should turn freely
clockwise and should lock counterclockwise.
3. Using a screwdriver, remove the snap ring from the
2nd brake hub.
4. Remove the one–way clutch from the 2nd brake
hub.
5. Using a small screwdriver, remove the retainer from
the 2nd brake hub.

5A2 – 182IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
Assembly Procedure
1. Install the retainer to the 2nd brake hub.
2. Install the one–way clutch.
3. Using a screwdriver, install the snap ring.
4. Install the one–way clutch and thrust washer to the
rear planetary sun gear.
5. Hold the rear planetary sun gear and turn the one–
way clutch. The one–way clutch should turn freely
clockwise and should lock counterclockwise.

AISIN AUTOMATIC TRANSAXLE 5A2 – 203
DAEWOO V–121 BL4
Upper Valve Body Key
MarkRetainerHeight/Width/Thickness mm (in.)
ACheck valve11.5 (0.453) / 5.0 (0.197) / 3.2 (0.126)
BSecondary regulator valve16.0 (0.630) / 5.0 (0.197) / 3.2 (0.126)
CLock up control valve16.0 (0.630) / 5.0 (0.197) / 3.2 (0.126)
DReverse control valve11.5 (0.453) / 5.0 (0.197) / 3.2 (0.126)

5A2 – 222IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
AUTOMATIC TRANSAXLE SYSTEM
Function of Components
ComponentFunction
C1Forward ClutchConnects input shaft and front sun gear.
C2Direct ClutchConnects input shaft and planetary carrier.
C3Reverse ClutchConnects input shaft and rear sun gear.
B1O/D & 2nd BrakePrevents rear planetary sun gear from turning either clockwise
or counterclockwise.
B22nd BrakePrevents outer race of F1 from turning either clockwise or coun-
terclockwise, thus preventing the rear sun gear turning conter-
clockwise.
B31st & Reverse BrakePrevents planetary carrier from turning either clockwise or
counterclockwise.
F1No.1 One–way ClutchWhen B2 is operating, this clutch prevents rear sun gear from
counterclockwise.
F2No.2 One–way ClutchPrevents planetary carrier from turning counterclockwise.
Planetary GearThese gears change the route through which driving froce is
transmitted, in accordance with the operation of each clutch
and brake, in order to increase or reduce the input and output
speed.

AISIN AUTOMATIC TRANSAXLE 5A2 – 223
DAEWOO V–121 BL4
Operations of Clutches and Brakes
Clutch & BrakeOperation
C1Forward ClutchConnects intermediate shaft and front sun gear.
C2Direct ClutchConnects input shaft and Planetary carrier.
C3Reverse ClutchConnects intermediate shaft and rear sun gear.
B1O/D & 2nd BrakeLock rear sun gear
B22nd BrakeLock rear sun gear
B31st & Reverse BrakeLock Planetary carrier
F11way Clutch No.1Lock counterclockwise rotation of rear sun gear, when B2 op-
erations
F21way Clutch No.2Lock counterclockwise rotation of planetary carrier

AISIN AUTOMATIC TRANSAXLE 5A2 – 225
DAEWOO V–121 BL4
D–1st Gear
PositionSolenoidClutchBrake1 way
Clutch
Shift 1Shift 2TimingC1C2C3B1B2B3F1F2
D1stONONOFFONOFFOFFOFFOFFOFFOF
–FON
11stONONOFFONOFFOFFOFFOFFONOF
–FON
”D” – 1st Gear
1. Input shaft rotates clockwise.
S Forward clutch (C1) operates. (Connect input shaft to front sun gear)
2. Front sun gear rotates clockwise.
3. Planetary short pinion rotates itself counterclockwise.
4. Planetary long Pinion rotates itself clockwise.
5. Planetary carrier is going to rotate counterclockwise.
S One way clutch No.2(F2) operates. (Lock revolves counterclockwise of planetary carrier)

5A2 – 226IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
6. Ring gear rotates clockwise.
7. Counter drive gear rotates clockwise for ring gear and one.
8. Counter drive gear rotates counterclockwise
9. Differential gear drive pinion rotates counterclockwise for counter driven gear and one.
10. Differential gear rotates clockwise.
( Engine Brake)
1. Counter drive gear and Planetary ring gear rotates counterclockwise.
2. Planetary long pinion rotates itself counterclockwise.
3. Planetary short pinion rotates itself clockwise.
4. Planetary carrier revolves clockwise due to rotation itself counterclockwise of planetary long pinion, but driving
force loses due to free of 1 way clutch NO.2 (F2). Therefore Engine brake does not operate.