tow DODGE JOURNEY 2009 1.G Owner's Manual

16. Electronic Throttle Control (ETC) Warning Light —
If EquippedThis light will turn on briefly as a bulb check
when the ignition switch is turned ON. This
light will also turn on while the engine is
running if there is a problem with the Elec-
tronic Throttle Control (ETC) system.
If the light turns on while the engine is running, safely
bring the vehicle to a complete stop as soon as possible,
place the shift lever in PARK, and cycle the ignition key.
The light should turn off. If the light remains lit with the
engine running, your vehicle will usually be drivable.
However, see your authorized dealer for service as soon
as possible.
If the light is flashing when the engine is running,
immediate service is required. In this case, you may
experience reduced performance, an elevated/rough idle
or engine stall, and your vehicle may require towing. Also, have the system checked by an authorized dealer if
the light does not turn on during starting.
17. Oil Pressure Warning Light
This light shows low engine oil pressure. The light
will turn on and remain on when the ignition
switch is turned from the LOCK or ACC position to the
ON position. The light will turn off after the engine is
started.
If the light does not turn on during starting, have the
system checked by an authorized dealer.
If the light turns on and remains on while driving, safely
bring the vehicle to a stop and shut off the engine. DO
NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS
CORRECTED. This light does not show the quantity of
oil in the engine. The engine oil level must be checked
using the proper procedure. (See page 424 for more
information.)
UNDERSTANDING YOUR INSTRUMENT PANEL 211
4

stays on through several of your typical driving cycles. In
most situations, the vehicle will drive normally and will
not require towing.
If the MIL flashes when the engine is running, serious
conditions may exist that could lead to immediate loss of
power or severe catalytic converter damage. (See page
421 for more information.)
CAUTION!
Prolonged driving with the MIL on could cause
further damage to the emissions control system. It
could also affect fuel economy and driveability. The
vehicle must be serviced before any emissions tests
can be performed.
If the MIL is flashing while the engine is running,
severe catalytic converter damage and power loss
will soon occur. Immediate service is required.25. Electronic Stability Program (ESP)/Brake Assist
System (BAS) Malfunction Indicator Light – If
Equipped
The yellow ESP/BAS Malfunction Indicator
Light will turn on when the ignition switch is
turned to the ON position. The light should go
out with the engine running. The system will
turn the light on continuously while the engine is run-
ning if it detects a malfunction in either the ESP or the
BAS or both. If this light remains on after the several
ignition cycles, and the vehicle has been driven several
miles (kilometers) at speeds greater than 30 mph (48
km/h), see your authorized dealer as soon as possible to
have the problem diagnosed and corrected. (See page 328
for more information.)
216 UNDERSTANDING YOUR INSTRUMENT PANEL

•PanelAir is directed through the outlets in the instrument
panel. For vehicles equipped with a three-zone sys-
tem, air is also directed through the outlets in the
headliner, unless the climate control for the rear passen-
gers is ON and in Floor mode.
NOTE: These outlets are adjustable to direct airflow. For
maximum airflow to the rear, aim the center instrument
panel outlets so that they are directed toward the rear
seat passengers.
•Bi-Level Air is directed through the panel and floor outlets.
For vehicles equipped with a three-zone system, air
is also directed through the outlets in the headliner,
unless the climate control for the rear passengers is ON
and in Floor mode.
NOTE: For all settings except full cold or full hot, there
is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets.
This feature gives improved comfort during sunny but
cool conditions.
•Floor
Air is directed through the floor outlets with a
small amount flowing through the defrost and side
window demist outlets. For vehicles equipped with a
three-zone system, air is directed through the floor outlet
in the right quarter trim panel, unless the climate control
for the rear passengers is ON and in Panel mode.
•Mix
Air is directed through the floor, defrost, and side
window demist outlets. For vehicles equipped with
a three-zone system, air is directed through the floor
outlet in the right quarter trim panel, unless the climate
control for the rear passengers is ON and in Panel mode.
286 UNDERSTANDING YOUR INSTRUMENT PANEL

Side Window Demisters
A side window demister outlet is located at each end of
the instrument panel. These non-adjustable outlets direct
air toward the side windows when the system is in the
Floor, Mix, or Defrost mode. The air is directed at the area
of the windows through which you view the outside
mirrors.
Outside Air Intake
Make sure the air intake, located directly in front of the
windshield, is free of obstructions such as leaves. Leaves
collected in the air intake may reduce airflow, and if they
enter the plenum, they could plug the water drains. In
Winter months, make sure the air intake is clear of ice,
slush, and snow.
A/C Air Filter — If Equipped
The A/C Air Filter will reduce, but not eliminate, diesel
and agricultural smells. The filter acts on air coming from
outside the vehicle and recirculated air within the pas-
senger compartment. Refer to “Maintenance Procedures”
in Section 7 for A/C Air Filter service information or see
your authorized dealer for service. Refer to the Mainte-
nance Schedule in Section 8 for filter service intervals.
UNDERSTANDING YOUR INSTRUMENT PANEL 301
4

▫Loose Fuel Filler Cap Message ............374
 Vehicle Loading ........................375
▫ Vehicle Certification Label ...............375
▫ Gross Vehicle Weight Rating (GVWR) .......375
▫ Gross Axle Weight Rating (GAWR) .........375
▫ Overloading .........................376
▫ Loading ............................376
 Trailer Towing .........................377
▫ Common Towing Definitions .............377▫
Trailer Hitch Classification ...............381
▫ Trailer Towing Weights (Maximum Trailer
Weight Ratings) ......................382
▫ Trailer And Tongue Weight ..............384
▫ Towing Requirements ..................385
▫ Towing Tips .........................390
 Recreational Towing (Behind Motorhome, Etc.) . . 392
▫ Towing This Vehicle Behind Another
Vehicle (Flat Towing With All Four Wheels
On The Ground) ......................392
306 STARTING AND OPERATING

If Engine Fails To Start
WARNING!
•Never pour fuel or other flammable liquids into
the throttle body air inlet opening in an attempt to
start the vehicle. This could result in a flash fire
causing serious personal injury.
•Do not attempt to push or tow your vehicle to get
it started. Vehicles equipped with an automatic
transaxle cannot be started this way. Unburned
fuel could enter the catalytic converter and once
the engine has started, ignite and damage the
converter and vehicle. If the vehicle has a dis-
charged battery, booster cables may be used to
obtain a start from a booster battery or the battery
in another vehicle. This type of start can be dan-
gerous if done improperly. Refer to Section 6 for
proper jump-starting procedures and follow them
carefully.If the engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weather” proce-
dures, it may be flooded. To clear any excess fuel, push
the accelerator pedal all the way to the floor and hold it.
Then, turn the ignition switch to the START position and
release it as soon as the starter engages. The starter motor
will disengage automatically in 10 seconds. Once this
occurs, release the accelerator pedal, turn the ignition
switch to the LOCK position, wait 10 to 15 seconds, then
repeat the normal starting procedure.
CAUTION!
To prevent damage to the starter, wait 10 to 15
seconds before trying again.
310 STARTING AND OPERATING

Gear Ranges
PARK
PARK supplements the parking brake by locking the
transaxle. The engine can be started in this range. Never
attempt to use PARK while vehicle is in motion. Apply
parking brake when leaving vehicle in this range.
When parking on a flat surface, place the shift lever in the
PARK position first, and then apply the parking brake.
When parking on a hill, it is important to set the parking
brake before placing the shift lever in PARK, otherwise
the load on the transaxle locking mechanism may make it
difficult to move the shift lever out of PARK. As an added
precaution, turn the front wheels toward the curb on a
downhill grade and away from the curb on an uphill
grade.
WARNING!
Never use PARK position on an Automatic Transaxle
as a substitute for the parking brake. Always apply
parking brake fully when parked to guard against
vehicle movement and possible injury or damage.
CAUTION!
DO NOT race the engine when shifting from PARK
or NEUTRAL positions into another gear range as
this can damage the drivetrain.
REVERSE
Use REVERSE for moving the vehicle rearward. Shift into
REVERSE only after the vehicle has come to a complete
stop.
314 STARTING AND OPERATING

NEUTRAL
The engine may be started in this range.
WARNING!
Do not coast in NEUTRAL and never turn off the
ignition to coast down a hill. These are unsafe
practices that limit your response to changing traffic
or road conditions. You might lose control of the
vehicle and have an accident.
DRIVE — 6-Speed Transaxle
This range should be used for most city and highway
driving. It provides the smoothest upshifts, downshifts,
and best fuel economy. However, use the AutoStick
mode and select the “5” range when frequent transaxle
shifting occurs while using the DRIVE range, such as
when operating the vehicle under heavy loading condi-
tions, (i.e., in hilly terrain, traveling into strong head winds or while towing heavy trailers). Under these
conditions, using the “5” range will improve perfor-
mance and extend transaxle life by reducing excessive
shifting and heat build-up.
“D” (Overdrive) — 4-Speed Transaxle
This range should be used for most city and highway
driving. It provides the smoothest upshifts, downshifts,
and best fuel economy. However, select the “3” range
when frequent transaxle shifting occurs while using the
“D” (Overdrive) range, such as when operating the
vehicle under heavy loading conditions, (i.e., in hilly
terrain, traveling into strong head winds or while towing
heavy trailers). Under these conditions, using the “3”
range will improve performance and extend transaxle life
by reducing excessive shifting and heat build-up.
STARTING AND OPERATING 315
5

PARK, REVERSE, and NEUTRAL will continue to oper-
ate. This Reset feature allows the vehicle to be driven to
an authorized dealer for service without damaging the
transaxle.
In the event of a momentary problem, the transaxle can
be reset to regain all forward gears by performing the
following steps:
1. Stop the vehicle.
2. Shift into PARK.
3. Turn the ignition switch to the LOCK position.
4. Restart the engine.
5. Shift into the desired gear range and resume driving.
NOTE:Even if the transaxle can be reset, it is recom-
mended that you visit an authorized dealer at your earliest possible convenience. Your authorized dealer has
diagnostic equipment to determine if the problem could
recur.
If the transaxle cannot be reset, authorized dealer service
is required.
AUTOSTICK
— IF EQUIPPED
AutoStickis a driver-interactive transaxle that offers six
manual ratio changes to provide you with more control
of the vehicle. AutoStick allows you to maximize engine
braking, eliminate undesirable upshifts and downshifts,
and improve overall vehicle performance. This system
can also provide you with more control during passing,
city driving, cold slippery conditions, mountain driving,
trailer towing, and many other situations.
STARTING AND OPERATING 317
5

As an added precaution, turn the front wheels toward the
curb on a downhill grade and away from the curb on an
uphill grade.
The foot operated parking brake is positioned below the
lower left corner of the instrument panel. To apply the
parking brake, push the parking brake pedal down and
then remove your foot from the pedal. To release the
parking brake, push down on the parking brake pedal
and then release.The brake light in the instrument cluster will turn on
when the parking brake is applied and the ignition
switch is in the ON position.
Parking Brake
324 STARTING AND OPERATING