DODGE RAM 1500 1998 2.G Workshop Manual

DODGE RAM 1500 1998 2.G Workshop Manual RAM 1500 1998 2.G DODGE DODGE https://www.carmanualsonline.info/img/12/5702/w960_5702-0.png DODGE RAM 1500 1998 2.G Workshop Manual
Trending: child, Belt tensioner, parking sensors, Driver seat, overheating, Gauge cluster wire harness, Idle Air Control Valve

Page 2331 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual EXTERIOR
TABLE OF CONTENTS
page page
BODY SIDE MOLDINGS
REMOVAL.............................36
INSTALLATION.........................36
BODY ISOLATORS
REMOVAL.............................36
INSTALLATIO

Page 2332 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual INSTALLATION
(1) For the rear isolators install the rebound cush-
ions, washers, reinforcement plates and bolts. (Fig. 1)
(2) Install the remaining rebound cushions and
bolts.
(3) Tighten the bolts to

Page 2333 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual CARGO BOX - TIE DOWN
REMOVAL
(1) Remove the bolts and remove the tie down
cleat. (Fig. 4)
INSTALLATION
(1) Install the tie down cleat and install the bolts.
(2) Tighten the bolts to 34 N´m (25 ft. lb

Page 2334 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual FRONT FENDER
REMOVAL
(1) Remove the antenna, if equipped. (Refer to 8 -
ELECTRICAL/AUDIO/ANTENNA BODY & CABLE -
REMOVAL)
(2) Remove the battery tray, if required. (Refer to 8
- ELECTRICAL/BATTERY SYST

Page 2335 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual GRILLE
REMOVAL
(1) Open the hood.
(2) Remove the six lower screws. (Fig. 8)
(3) Remove the six upper nuts and separate the
grille from the grille frame.
INSTALLATION
(1) Position the grille onto the g

Page 2336 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual FRONT WHEELHOUSE
SPLASH SHIELD
REMOVAL
(1) Remove the three screws at the fender. (Fig.
10)
(2) Remove the electrical connector push pin fas-
tener.
(3) Remove the five inside screws and remove the
sp

Page 2337 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual INSTALLATION
(1) Install the mirror onto the door and engage the
electrical connector tabs. (Fig. 13)
(2) Install the nuts and tighten to 7 N´m (60 in.
lbs.).
(3) Install the door trim panel. (Refer

Page 2338 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual (2) Disengage the rear housing cover retaining
tabs and remove the cover. (Fig. 17)
(3) Disengage the lower glass retaining tab to
motor. (Fig. 18)
(4) Slide glass up and remove from motor.
(5) Discon

Page 2339 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual (2) Connect the heated mirror electrical connec-
tors, if equipped.
NOTE: Pressure must be applied equally over the
center portion of the mirror to engage the mirror
glass retaining clip fully.
(3) Po

Page 2340 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual (1) Carefully position the fender over the support
brackets.
(2) Install the four inner nuts along the front edge
of the fender and tighten to 7 N´m (60 in. lbs.).(3) Install the two inner nuts along
Trending: wheel torque, Transmission cooler radiator, Locks, key fob battery, Brake system, Crank, cruise control