light DODGE RAM 1999 Service Repair Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 1480 of 1691
Transmission Governor Pressure Solenoid
See TRANSMISSION GOVERNOR SOLENOID under MISCELLANEOUS
CONTROLS.
Transmission Overdrive/Override (OD/OR) Switch Indicator
Light
See TRANSMISSION OVERDRIVE/OVERRIDE (OD/OR) SWITCH INDICATOR
under MISCELLANEOUS CONTROLS.
Transmission Overdrive (OD) Solenoid
See TRANSMISSION OVERDRIVE (OD) SOLENOID under MISCELLANEOUS
CONTROLS.
FUEL SYSTEM
FUEL DELIVERY
Auto Shutdown (ASD) Relay
See AUTO SHUTDOWN (ASD) RELAY & FUEL PUMP RELAY under
MISCELLANEOUS CONTROLS.
Fuel Pressure Regulator
Fuel pressure regulator is a mechanical device, used to
maintain a constant pressure across fuel injector tip. Spring and
rubber diaphragm will move from an open to closed position keeping
fuel pressure constant. Excess fuel is returned to fuel tank.
Regulator is located in in-tank fuel pump module. Regulator
includes an internal fuel filter. Excess fuel is routed directly into
fuel tank without using a return line. See Fig. 2.
Fig. 2: Cross-Sectional View Of In-Tank Fuel Filter/Fuel Pressure
Regulator (Typical)
Courtesy of Chrysler Corp.
In-Tank Fuel Pump
Page 1485 of 1691
Crankcase Ventilation (PCV) system, but does not use a vacuum
controlled valve. See POSITIVE CRANKCASE VENTILATION (PCV).
EVAPORATIVE (EVAP) EMISSIONS SYSTEM
This system stores fuel vapors from fuel tank, preventing
vapors from reaching the atmosphere. As fuel evaporates inside fuel
tank, vapors are routed through vent hoses to charcoal canister where
they are stored until engine is started.
Evaporative Canister Purge Control Solenoid (EVAP-CPCS)
Charcoal canister purging is controlled by PCM through an
EVAP-CPCS. During engine warm-up and for a short period after hot
restarts, PCM energizes EVAP-CPCS, interrupting engine vacuum signal
to charcoal canister.
After engine reaches a predetermined operating temperature
and PCM internal timer has expired, PCM will de-energize EVAP-CPCS,
allowing engine vacuum to purge charcoal canister. EVAP-CPCS will also
be de-energized during certain idle conditions so PCM can update fuel
delivery calibration.
POSITIVE CRANKCASE VENTILATION (PCV)
PCV system uses a vacuum operated valve. A closed engine
crankcase breather/filter, with a hose connecting it to air filter
housing, provides source of air for system. Crankcase blow-by gases
are removed from crankcase through PCV valve with manifold vacuum.
These gases are introduced into incoming air/fuel mixture and become
part of the calibrated mixture.
A non-vacuum operated Crankcase Ventilation (CCV) system is
used on some engines, see CRANKCASE VENTILATION (CCV) SYSTEM.
SELF-DIAGNOSTIC SYSTEM
The PCM monitors several different circuits of engine control
system. If a problem is sensed with a monitored circuit, PCM will
store a Diagnostic Trouble Code (FTC) to aid technician in diagnosis
of system. The Malfunction Indicator Light (MIL), or a scan tool can
be used to read DTCs. For additional information, see SELF-DIAGNOSTICS
- JEEP, TRUCKS & RWD VANS article.
MALFUNCTION INDICATOR LIGHT
Malfunction Indicator Light (MIL) comes on and remains on for\
3 seconds as a bulb test each time ignition switch is turned to ON
position. If PCM receives an incorrect signal or receives no signal
from battery voltage input, charging system, ECT sensor, MAP sensor or
TP sensor, MIL will come on. MIL will also come on if certain
emission-related faults exist. This warns driver that PCM is in limp-
in mode and immediate repairs are necessary. See LIMP-IN MODE under
MISCELLANEOUS CONTROLS. MIL can also be used to display Diagnostic
Trouble Codes (DTCs). For additional information, see SELF-DIAGNOSTICS\
- JEEP, TRUCKS & RWD VANS article.
SERIAL COMMUNICATIONS INTERFACE (SCI)
SCI circuit is used by PCM to send data to and receive data
and sensor activation signals from scan tool. Scan tool uses signals
sent on SCI to display fault messages or Diagnostic Trouble Codes
(DTCs), sensor voltages and device states (On/Off). Scan tool uses S\
CI
to send solenoid and switch activation commands to PCM so that devices
and circuits can be tested. SCI is also used to write SRI mileage to
Page 1486 of 1691
PCM.
MISCELLANEOUS CONTROLS
NOTE: Although not strictly considered part of engine performance
system, some controlled devices can adversely affect
driveability if they malfunction.
A/C CLUTCH RELAY
A/C clutch relay is controlled by PCM. When A/C or Defrost
mode is selected and PCM receives A/C request signal from evaporator
switch, PCM will cycle clutch on and off through A/C clutch relay.
When this relay is energized during engine operation, PCM will
determine correct engine idle speed through IAC motor.
When PCM senses low idle speed or wide open throttle through
TP sensor, PCM will de-energize A/C clutch relay, preventing A/C
operation.
AUTO SHUTDOWN (ASD) RELAY & FUEL PUMP RELAY
ASD relay and electric fuel pump relay are energized when
ignition is on. These relays are controlled through PCM by switching a
common ground circuit on and off. Following components are controlled
by ASD and fuel pump relays:
* Electric Fuel Pump
* Fuel Injectors
* Generator Field Winding
* Ignition Coil(s)
* HO2S Heating Element
When ignition switch is turned to RUN position, PCM energizes
ASD relay and electric fuel pump relay which powers these components.
If PCM does not receive a CMP and CKP sensor signal within one second
of engine cranking (start-up), PCM will turn ground circuit off and
de-energize ASD relay.
GENERATOR
Powertrain Control Module (PCM) regulates charging system
voltage.
LIMP-IN MODE
Limp-in mode is the attempt by PCM to compensate for failure
of certain components by substituting information from other sources
so that vehicle can still be operated. If PCM senses incorrect data or
no data at all from MAP sensor, TP sensor, ECT sensor or battery
voltage, system is placed into limp-in mode and Malfunction Indicator
Light (MIL) on instrument panel comes on.
If faulty sensor comes back on line, PCM will resume closed
loop operation. On some vehicles, MIL will remain on until ignition is
shut off and vehicle is restarted. To prevent damage to catalytic
converter, vehicle should NOT be driven for extended periods in limp-
in mode.
RADIATOR FAN RELAY
Electric cooling fan is used only on Dakota. Using
information supplied by A/C signal (if equipped), ECT sensor, and VSS,\
Page 1487 of 1691
PCM controls operation of electric cooling fan. PCM operates fan
through radiator fan relay by grounding or ungrounding relay control
circuit. PCM regulates engine idle speed through IAC motor when fan is
on.
SHIFT INDICATOR LIGHT
PCM provides ground for shift indicator light on models
equipped with manual transmission. Based on engine speed, throttle
position, and vehicle speed, PCM turns shift indicator light on to
advise driver to shift to a higher gear for optimum fuel economy.
SPEED CONTROL SERVO
System is electrically actuated and vacuum operated. Controls
are located on steering wheel. Controls consist of 3 buttons: OFF/ON,
RESUME/ACCEL and SET/DECEL. Speed control servo is controlled by PCM.
System will operate at 35-85 MPH.
TACHOMETER
PCM provides signal to drive tachometer.
TORQUE CONVERTER CLUTCH (TCC) SOLENOID
PCM controls torque converter lock-up through TCC solenoid.
PCM controls lock-up according to various operating conditions.
TRANSMISSION GOVERNOR SOLENOID
PCM controls solenoid to regulate line pressure for shift
control.
TRANSMISSION OVERDRIVE/OVERRIDE (OD/OR) SWITCH INDICATOR
LIGHT
PCM controls indicator light on OD/OR switch on models
equipped with overdrive automatic transmission.
TRANSMISSION OVERDRIVE (OD) SOLENOID
On models equipped with OD transmission, PCM controls 3-4 OD
upshift and downshift through OD solenoid. PCM determines optimum OD
shift scheduling for all operating conditions.
Page 1488 of 1691
TR AN SM IS SIO N R EM OVA L & IN STA LLA TIO N
1999 D odge P ic ku p R 1500
1998-99 TRANSMISSION SERVICING
CHRY - Trans Removal & Installation - Trucks & RWD Vans
Dakota, Ram Pickup, Ram Van/Wagon
WARNING: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
MANUAL TRANSMISSION
NOTE: For manual transmission replacement procedures, see
appropriate article in CLUTCHES.
AUTOMATIC TRANSMISSION
DAKOTA & DURANGO
Removal
1) Disconnect negative battery cable. Raise and support
vehicle. Disconnect and remove necessary skid plates and exhaust
components for transmission removal. Remove engine-to-transmission
struts (if equipped). These struts are located between front of
transmission and engine.
2) Ensure area around transmission oil cooler lines fitting
are clean. Disengage retainer on quick-disconnect cooler line fitting.
Pull cooler line from transmission oil cooler.
CAUTION: Crankshaft position sensor must be removed from transmission
housing before removing transmission to prevent damage to
crankshaft position sensor.
3) Remove starter. Disconnect electrical connector for
crankshaft position sensor. On 2.5L, crankshaft position sensor is
mounted on driver's side of transmission housing. See Fig. 1. On 3.9L,
5.2L and 5.9L, crankshaft position sensor is mounted on passenger's
side of transmission housing. See Fig. 2.
4) Remove crankshaft position sensor bolts or nuts. Remove
crankshaft position sensor from transmission housing. Remove dipstick,
dipstick tube and "O" ring from transmission.
5) Remove torque converter cover. Place reference mark on
flexplate and torque converter for installation reference. Rotate
crankshaft clockwise and remove torque converter bolts.
6) Place reference mark on drive shaft flanges for
installation reference. Remove drive shaft from transmission. On 4WD
models, disconnect drive shaft from transfer case. Disconnect shift
rod for transfer case from transfer case shift lever.
7) On all models, disconnect necessary control cables, wiring
harnesses, and shift linkage or cable from transmission. Support rear
of engine with jack stand. Using transmission jack, slightly raise
transmission to release pressure from rear mount and rear crossmember.
8) Remove bolts securing rear support and rear mount to
transmission and rear crossmember. Raise transmission slightly. Slide
exhaust hanger arm from bracket on rear support. Remove rear support
and rear mount.
9) Remove rear crossmember located below the transmission. On
4WD models, disconnect electrical connectors from transfer case. On
Page 1490 of 1691
Courtesy of Chrysler Corp.
Installation
1) To install, reverse removal procedure. Ensure torque
converter is fully seated in transmission by measuring distance from
cylinder block surface on transmission housing to front edge on torque
converter bolt lug on front of torque converter. Distance should be .
50" (12.7 mm) if torque converter is fully seated.
CAUTION: Proper length torque converter bolts must be used. If
replacing any torque converter bolts, ensure proper length
bolt is used.
2) Tighten bolt/nuts to specification. See TORQUE
SPECIFICATIONS. Ensure reference mark on torque converter and
flexplate, and drive shaft flanges are aligned. Adjust shift cable or
linkage, throttle valve cable and transfer case shift linkage if
necessary. See AUTOMATIC TRANSMISSION - TRUCKS & RWD VANS article.
3) Use NEW "O" ring when installing dipstick tube. Before
installing oil cooler lines on transmission, ensure all fittings are
clean. Install oil cooler line into quick-disconnect fitting. Push oil
cooler line inward until a click is heard. Pull on oil cooler line to
ensure oil cooler line is locked in place. Fill transmission with
Mopar ATF Plus Type 7176.
RAM PICKUP
Removal
1) Disconnect negative battery cable. Raise and support
vehicle. Disconnect and remove necessary skid plates and exhaust
components for transmission removal. Remove engine-to-transmission
struts (if equipped). These struts are located between front of
transmission and engine.
2) Ensure area around transmission oil cooler lines fitting
are clean. Disengage retainer on quick-disconnect cooler line fitting.
Pull cooler line from transmission oil cooler. Remove starter.
CAUTION: On 3.9L, 5.2L and 5.9L gasoline models, crankshaft position
sensor must be removed from transmission housing before
removing transmission to prevent damage to crankshaft
position sensor.
3) On 3.9L, 5.2L and 5.9L gasoline models, disconnect
electrical connector for crankshaft position sensor. Crankshaft
position sensor is mounted on passenger's side of transmission
housing. See Fig. 2.
4) Remove crankshaft position sensor bolts. Remove crankshaft
position sensor from transmission housing. Remove dipstick, dipstick
tube and "O" ring from transmission.
5) Remove torque converter cover. Place reference mark on
flexplate and torque converter for installation reference. Rotate
crankshaft clockwise and remove torque converter bolts.
6) Place reference mark on drive shaft flanges for
installation reference. Remove drive shaft from transmission. On 4WD
models, disconnect drive shaft from transfer case. Disconnect shift
rod for transfer case from transfer case shift lever.
7) On all models, disconnect necessary control cables, wiring
harnesses, and shift linkage from transmission. Support rear of engine
with jack stand. Using transmission jack, slightly raise transmission
to release pressure from rear mount and rear crossmember.
8) Remove bolts securing rear support and rear mount to
transmission and rear crossmember. Raise transmission slightly. Slide
exhaust hanger arm from bracket on rear support. Remove rear support
Page 1491 of 1691
and rear mount.
9) Remove rear crossmember located below the transmission. On
4WD models, disconnect electrical connectors from transfer case. On
all models, remove transmission-to-cylinder block bolts. Slide
transmission rearward from dowels on cylinder block.
10) Install "C" clamp on edge of transmission housing to hold
torque converter in place. Lower transmission and remove transmission
from vehicle.
Installation
1) To install, reverse removal procedure. Ensure torque
converter is fully seated in transmission by measuring distance from
cylinder block surface on transmission housing to front edge on torque
converter bolt lug on front of torque converter. Distance should be .
50" (12.7 mm) if torque converter is fully seated.
CAUTION: Proper length torque converter bolts must be used. If
replacing any torque converter bolts, consult parts
department to ensure proper length bolt is used.
2) Tighten bolt/nuts to specification. See TORQUE
SPECIFICATIONS. Ensure reference mark on torque converter and
flexplate, and drive shaft flanges are aligned. Adjust shift linkage,
throttle valve cable and transfer case shift linkage if necessary. See
AUTOMATIC TRANSMISSION - TRUCKS & RWD VANS article.
3) Use NEW "O" ring when installing dipstick tube. Before
installing oil cooler lines on transmission, ensure all fittings are
clean. Install oil cooler line into quick-disconnect fitting. Push oil
cooler line inward until a click is heard. Pull on oil cooler line to
ensure oil cooler line is locked in place. Fill transmission with
Mopar ATF Plus Type 7176.
RAM VAN/WAGON
Removal
1) Disconnect negative battery cable. Raise and support
vehicle. Remove engine-to-transmission struts. These struts are
located between front of transmission and engine.
2) Remove starter and oil cooler line bracket. Ensure area
around transmission oil cooler lines fitting are clean. Disengage
retainer on quick-disconnect cooler line fitting. Pull cooler line
from transmission oil cooler.
CAUTION: Crankshaft position sensor must be removed from transmission
housing before removing transmission to prevent damage to
crankshaft position sensor.
3) Disconnect electrical connector for crankshaft position
sensor. Crankshaft position sensor is mounted on passenger's side of
transmission housing. See Fig. 2.
4) Remove crankshaft position sensor bolts. Remove crankshaft
position sensor from transmission housing. Remove dipstick, dipstick
tube and "O" ring from transmission.
5) Remove torque converter cover. Place reference mark on
flexplate and torque converter for installation reference. Rotate
crankshaft clockwise and remove torque converter bolts.
6) Place reference mark on drive shaft yokes for installation
reference. Remove drive shaft from transmission. Disconnect necessary
wiring harnesses and control cables from transmission. Support rear of
engine with hoist. Using transmission jack, slightly raise
transmission to release pressure from rear mount and crossmember.
7) Remove rear mount-to-rear crossmember bolts. Remove bolts
and rear crossmember located below the transmission. Remove engine oil
Page 1496 of 1691
Ram Pickup
Gasoline Models
Light-Duty (2)
Normal Service ..................... 30 .............. 37,500
Severe Service ..................... ( 1) ............. 12,000
Medium-Duty & Heavy-Duty
Normal Service ..................... 24 .............. 24,000
Severe Service ..................... ( 1) ............. 12,000
Diesel Models
Normal Service ....................... 24 .............. 24,000
Severe Service ....................... ( 1) ............. 12,000
Ram Van/Wagon
Normal Service ........................ ( 3) ................ ( 3)
Severe Service ........................ ( 1) ............. 12,000
( 1) - Monthly interval is not available from manufacturer.
( 2) - Light-duty applies to all 1500 models and 2500 models except
5.9L diesel or 8.0L engines. Medium-duty applies to 2500 and
3500 California models with 8.0L engine. Heavy-duty applies to
2500 and 3500 Federal models with 8.0L engine and all 3500
models with 5.9L gasoline engine.
( 3) - Normal service interval is not available from manufacturer.
\
\
\
\
\
\
\
Transfer Case
Check transfer case fluid level when performing other
underhood services. Under normal service conditions or severe service
conditions change transfer case fluid at specified interval. See
TRANSFER CASE SERVICING INTERVALS table. Severe service conditions are
conditions such as long periods of engine idling, trailer towing, off-
highway operation, snow removal, or operating in dusty or excessively
hot conditions.
TRANSFER CASE SERVICING INTERVALS
\
\
\
\
\
\
\
Application Months Miles
Dakota
Normal Service ....................... 30 ............... 37,500
Severe Service ....................... ( 1) .............. 36,000
Ram Pickup
Gasoline Models
Light-Duty ( 2)
Normal Service .................... 30 ............... 37,500
Severe Service .................... ( 1) .............. 36,000
Medium-Duty & Heavy-Duty
Normal Service .................... 36 ............... 36,000
Severe Service .................... ( 1) .............. 36,000
Diesel Models
Normal Service ...................... 36 ............... 36,000
Severe Service ...................... ( 1) .............. 36,000
( 1) - Monthly interval is not available from manufacturer.
( 2) - Light-duty applies to all 1500 models and 2500 models except
5.9L diesel or 8.0L engines. Medium-duty applies to 2500 and
3500 California models with 8.0L engine. Heavy-duty applies to
2500 and 3500 Federal models with 8.0L engine and all 3500
models with 5.9L gasoline engine.
\
\
\
\
\
\
\
Power Take-Off (PTO) Adapter (Ram Pickup 2WD 2500 & 3500)
Check PTO adapter fluid level when performing other underhood
services. Service interval is not available from manufacturer.
Page 1507 of 1691
Transmission (Dakota)
Check transmission fluid level when performing other
underhood services. Under normal service conditions, change
transmission fluid at 30 months or 37,500 miles. Under severe service
conditions, change transmission fluid at 18,000 miles. Severe service
are conditions such as long periods of engine idling, trailer towing,
off-highway operation, snow removal, or operating in dusty or
excessively hot conditions.
Transmission (Ram Pickup)
Check transmission fluid level when performing other
underhood services. Fluid change service interval information is not
available from manufacturer.
Transfer Case
Check transfer case fluid level when performing other
underhood services. On Dakota and Light-Duty Pickup, change transfer
case fluid at 37,500 miles or 30 months. On Medium-Duty and Heavy-Duty
Pickup, change transfer case fluid at 36,000 miles or 36 months.
CHECKING FLUID LEVEL
Transmission (Dakota)
1) Park vehicle on level surface. Remove transmission fill
plug from side of transmission. On AX-15 transmission, transmission
fill plug is located on driver's side of transmission. On NV3500
transmission, transmission fill plug is located near front of
transmission on passenger's side of transmission.
2) On all transmissions, fluid level should even with bottom
of fill plug hole on side of transmission. Add appropriate type of
transmission fluid if necessary. See RECOMMENDED FLUID. Install and
tighten transaxle fill plug to specification. See TORQUE
SPECIFICATIONS.
Transmission (Ram Pickup)
1) Park vehicle on level surface. Remove transmission fill
plug from side of transmission. On NV3500 transmissions, transmission
fill plug is located near front of transmission on passenger's side of
transmission. On NV4500 transmissions, transmission fill plug is
located near rear of transmission on passenger's side of transmission.
2) On all transmissions, fluid level should even with bottom
of fill plug hole on side of transmission. Add appropriate type of
transmission fluid if necessary. See RECOMMENDED FLUID. Install and
tighten transaxle fill plug to specification. See TORQUE
SPECIFICATIONS.
Transfer Case
Park vehicle on level surface. Remove transfer case fill plug
from rear of transfer case. Fluid level should even with bottom of
transfer case fill plug hole on rear of transfer case. Add appropriate
type of transfer case fluid if necessary. See RECOMMENDED FLUID.
Install and tighten transfer case fill plug to specification. See
TORQUE SPECIFICATIONS.
RECOMMENDED FLUID
Transmission (Dakota)
On AX-15 transmissions, use API 75W-90 GL-3 gear oil. On
NV1500 and NV3500 transmissions, use ONLY Mopar M/T Lube Part No.
4761526.
Transmission (Ram Pickup)
Page 1509 of 1691
transmission housing.
2) Install and tighten transmission drain plug to
specification. See TORQUE SPECIFICATIONS.
3) Remove transmission fill plug from side of transmission.
Transmission fill plug is located near front of transmission on
passenger's side of transmission. Fill transmission with appropriate
type of transmission fluid until fluid level is even with bottom of
fill plug hole on transmission. See RECOMMENDED FLUID. Install and
tighten transmission fill plug to specification. See TORQUE
SPECIFICATIONS.
Transmission (Ram Pickup With NV4500 Or NV5600)
1) Park vehicle on level surface. Remove bottom bolt from
Power Take-Off (PTO) cover on passenger's side of transmission. Allow
fluid to drain.
2) Install and tighten PTO cover bolt to specification. See
TORQUE SPECIFICATIONS. Remove transmission fill plug from side of
transmission. Transmission fill plug is located near rear of
transmission on passenger's side of transmission.
3) Fill transmission with appropriate type of transmission
fluid until fluid level is even with bottom of fill plug hole on
transmission. See RECOMMENDED FLUID. Install and tighten transmission
fill plug to specification. See TORQUE SPECIFICATIONS.
Transfer Case
1) Ensure vehicle is parked on level surface. Remove transfer
case drain plug. Transfer case drain plug is located on rear of
transfer case at driver's side corner of transfer case. Allow fluid to
drain from transfer case.
2) Reinstall transfer case drain plug. Tighten transfer case
drain plug to specification. See TORQUE SPECIFICATIONS. Remove
transfer case fill plug fill plug from rear of transfer case. Transfer
case fill plug is located on rear of transfer case, just below
identification tag.
3) Fill transfer case with appropriate type of transfer case
fluid until fluid level is even with bottom of fill plug hole on
transfer case. See RECOMMENDED FLUID. Install and tighten transfer
case fill plug to specification. See TORQUE SPECIFICATIONS.
ADJUSTMENTS
TRANSFER CASE SHIFT LINKAGE
Dakota
1) On NV231, place transfer case lever in 4H position. On
NV242, place transfer case lever in 4FT position. On all models, use
wire or tape to hold lever in position. Raise and support vehicle.
Loosen shifter rod lock bolt at adjusting swivel. Ensure shift rod
slides freely in adjusting swivel.
2) Ensure shift lever on transfer case is in 4H position.
Slide adjusting swivel forward until shift lever touches shifter gate
crossover. Slide adjusting swivel slightly rearward to provide a 3-5
mm gap between shift lever shifter gate.
3) Center pin on adjusting swivel in shift arm and tighten
lock bolt to 90 INCH lbs. (10 N.m). Lower vehicle enough to enter
vehicle. Ensure wheels are off floor. Start engine and shift
transmission into gear. Operate transfer case to verify correct
adjustment.