light DODGE RAM 1999 Service Repair Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 1231 of 1691
Hazard Warning Lights Okay To Front Lights Only
Faulty external bulbs. Faulty contact in turn signal/hazard
switch. Open circuit between hazard switch and turn signal switch.
Open or grounded circuit in wiring to rear lights.
Hazard Warning Lights Okay To Rear Lights Only
Faulty external bulbs. Faulty contact in turn signal/hazard
switch. Open or grounded circuit in wiring to front lights.
Indicator Light Inoperative, External Lights Okay
Burned-out indicator bulb in instrument cluster. Faulty
contact. Open circuit.
Indicator Light Okay, External Lights Inoperative
Open circuit in wiring to external light(s).
Indicator Light Okay, External Lights Glow Dimly Or Do Not
Flash
Loose or corroded external light connections. Poor ground
circuit at external light(s).
Turn Signals Do Not Cancel After Turn
Broken canceling pawl on turn signal switch. Improperly
aligned canceling cam. Broken or loose canceling cam.
Turn Signals Inoperative (Both Sides)
Blown fuse. Faulty turn signal flasher. Loose bulkhead
connector. Loose or faulty rear wiring harness or terminals. Open
circuit to turn signal flasher. Open circuit in feed wire to turn
signal switch. Faulty switch connections. Open or grounded circuit in
wiring to external lights.
Turn Signal Inoperative (One Side)
Faulty external bulb. Poor ground at external light. Open
circuit in wiring to external light(s). Faulty turn signal/hazard
switch.
COMPONENT TESTS
CAUTION: When battery is disconnected, vehicle computer and memory
systems may lose memory data. Driveability problems may exist
until computer systems have completed a relearn cycle. See
COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION
before disconnecting battery.
NOTE: For additional testing procedures, see appropriate CRUISE
CONTROL SYSTEMS and WIPER/WASHER SYSTEMS articles.
NOTE: For component locations, see COMPONENT LOCATIONS.
HORN RELAY
1) Remove horn relay from Power Distribution Center (PDC).
Use label on PDC cover to identify and locate relay. Check continuity
between relay terminals No. 87A and 30. See Fig. 1. If continuity does
not exist, replace relay. If continuity exists, go to next step.
2) Check continuity between relay terminals No. 30 and 87. If
continuity exists, replace relay. If continuity does not exist, check
resistance between relay terminals No. 85 and 86. If resistance is not
70-80 ohms, replace relay. If resistance is 70-80 ohms, go to next
step.
3) Using jumper wires, connect positive battery voltage to
Page 1233 of 1691
![DODGE RAM 1999 Service Repair Manual ground. \
\
\
\
\
\
\
IGNITION SWITCH CIRCUIT FUNCTIONS](/img/12/56915/w960_56915-1232.png "DODGE RAM 1999 Service Repair Manual ground. \
\
\
\
\
\
\
IGNITION SWITCH CIRCUIT FUNCTIONS")
ground. \
\
\
\
\
\
\
IGNITION SWITCH CIRCUIT FUNCTIONS \
\
\
\
\
\
\
Terminal No. (Wire Color) Circuit\
1 (DK BLU/YEL) ...................... Ignition Switch Output (START\
)
2 (DK BLU) ...................... Ignition Switch Output (START/RUN\
)
3 (GRY/BLK) (1) ..................... Red Brake Warning Light Driver
4 (PNK/BLK) ............................... Battery Feed To Ignition\
5 (BLK/ORG) ........................... Ignition Switch Output (RUN\
)
6 (BLK/WHT) ....................... Ignition Switch Output (ACC/RUN\
)
7 (RED) ................................... Battery Feed To Ignition\
( 1) - White wire on Dakota and Durango.
\
\
\
\
\
\
\
Fig. 2: Identifying Ignition Switch Connector Terminals (Harness
Side)
Courtesy of Chrysler Corp.
MULTIFUNCTION SWITCH
Turn Signal/Hazard Warning Switch
Disconnect negative battery cable. Remove multifunction
switch. See MULTIFUNCTION SWITCH under REMOVAL & INSTALLATION. Check
continuity between appropriate multifunction switch terminals with
switch in specified position. See MULTIFUNCTION SWITCH TURN SIGNAL
TESTING table. See Fig. 3. If continuity is not as specified, replace
multifunction switch.
MULTIFUNCTION SWITCH TURN SIGNAL TESTING
\
\
\
\
\
\
\
Switch Position Continuity Between Terminals
Neutral
Hazard Warning On ............................ 11, 12, 13, 15 & 16
Hazard Warning Off ................................... 12, 14 & 15
Left .......................................... 12 & 14; 15, 16 & 17
Right ......................................... 14 & 15; 11, 12 & 17
Optional Corner Lights
Left ..................................................... 22 & 23
Right .................................................... 23 & 24
\
\
\
\
\
\
\
Page 1236 of 1691
switch connector. See Fig. 4. If continuity does not exist, repair
open Black/Red wire. If continuity exists, go to next step.
3) Check continuity between ground and Black/Red wire at
steering column horn switch connector. If continuity does not exist,
go to next step. If continuity exists, repair short to ground in
Black/Red wire.
4) Continuity between horn switch terminal and ground.
Continuity should exist with horn switch depressed. Continuity should
not exist without horn switch depressed. If continuity is not as
specified, replace horn switch. If continuity is as specified, install
horn relay and go to HORN under COMPONENT TESTS.
TURN SIGNAL & HAZARD WARNING SYSTEMS
1) If bulbs burn out rapidly, check charging system for
overcharging condition. See appropriate GENERATORS & REGULATORS
article in STARTING & CHARGING SYSTEMS. If charging system is okay, go
to next step. If charging system is not okay, repair as necessary.
2) If problem is turn signals failing to cancel after a turn,
inspect multifunction switch or cancelling cam lobes on clockspring
for damage or improper installation. If problem exists, repair as
necessary. If problem does not exist, go to next step.
3) Turn ignition on. Actuate turn signal switch or hazard
warning switch. Observe turn signal indicator light(s) in instrument
cluster. If flash rate is very high, check for a bulb that is not lit
or is dimly lit. Repair circuit or replace bulb as necessary. If turn
signals fail to light, go to next step.
4) Turn ignition off. Check turn signal fuse in junction
block and/or hazard warning fuse in PDC. If fuses are okay, go to next
step. If either fuse is blown, repair short circuit and replace fuse.
5) Check for battery voltage at hazard warning fuse in PDC.
Turn ignition on. Check for battery voltage at turn signal fuse in
junction block. If battery voltage exists, go to next step. If battery
voltage does not exist, repair open circuit to battery or ignition
switch as necessary.
6) Turn ignition off. Disconnect negative battery cable.
Remove combination flasher from junction block and replace with a
known good unit. Connect battery cable and test operation of turn
signal and hazard warning systems. If operation is okay, discard
faulty flasher. If operation is not okay, go to next step.
7) Turn ignition on. Check for battery voltage at combination
flasher terminals No. 51 and 48 in junction block. If battery voltage
exists, go to next step. If battery voltage does not exist, repair
open circuit to fuse in junction block or PDC as necessary.
8) Disconnect negative battery cable. Check continuity
between combination flasher terminal No. 50 and ground. If continuity
exists, go to next step. If continuity does not exist, repair open
ground circuit.
9) Disconnect multifunction switch harness connector. Check
continuity between junction block terminal No. 4 and multifunction
switch terminal No. 13 (Pink wire). If continuity exists, go to next
step. If continuity does not exist, repair open in Pink wire between
multifunction switch and junction block.
10) Check continuity between junction block terminal No. 13
and multifunction switch terminal No. 17 (Red/White wire). If
continuity exists, test multifunction switch. See MULTIFUNCTION SWITCH
under COMPONENT TESTS. If continuity does not exist, repair open in
Red/White wire between junction block and multifunction switch.
REMOVAL & INSTALLATION
WARNING: Deactivate air bag system before performing any service
Page 1238 of 1691
allows lock cylinder to mesh with switch. With key in lock cylinder,
turn lock cylinder to RUN position so retaining pin can be depressed.
Install lock cylinder in ignition switch (aligning slot) until
retaining pin engages. Turn key to OFF or LOCK position.
2) Pull on lock cylinder to ensure retaining pin is retained
in ignition switch and cylinder will not come out. On vehicles with
automatic transmission, ensure shifter is in Park and dowel pin on
ignition switch is in Park position. Ensure ignition switch is in LOCK
position. On all models, ensure flag on ignition switch is properly
indexed in Park position. The flag operates steering lock.
3) On vehicles with automatic transmission, apply a light
coating of grease to park lock dowel and park lock slider linkage. See
Fig. 6. Slide park lock slider linkage forward completely, then back .
25" (6 mm). Apply a light coating of grease to column lock flag.
4) Carefully install ignition switch on steering column,
ensuring flag is positioned above steering wheel lock lever, dowel
pins on switch align in holes on steering column and park lock dowel
pin slides into park lock slider linkage (automatic transmission
only). See Fig. 7. Tighten mounting screws to 22-30 INCH lbs. (2.5-3.5
N.m).
5) Connect wiring connectors to ignition switch. Install
upper and lower steering column covers. Tighten screws to 17 INCH lbs.
(2 N.m). Install tilt lever (if equipped). Reconnect negative batter\
y
cable. Check for proper operation of ignition switch in all positions.
Check for proper steering wheel lock operation. Check for proper
automatic shift lock operation.
Fig. 6: Positioning Park Lock Slider Linkage
Courtesy of Chrysler Corp.
Page 1268 of 1691
![DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SU](/img/12/56915/w960_56915-1267.png "DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SU")
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SUSPENSION - WARNING LAMP INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bulb burned out ......... A ............ Require replacement.
Warning light does
not come on during
bulb check ............. .. . Further inspection required to
determine cause.
Warning light flashes ... .. . Further inspection required to
determine cause.
Warning light is
intermittent ........... .. . Further inspection required to
determine cause.
Warning light stays
on after initial
bulb check ............. .. . Further inspection required to
determine cause.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - WIRING HARNESSES
AIR RIDE SUSPENSION - WIRING HARNESS INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Connector bent .......... A .. Require repair or replacement.
Connector broken ........ A .. Require repair or replacement.
Connector loose ......... A .. Require repair or replacement.
Damaged (cut, burned, or
chafed) ................ A .. Require repair or replacement.
Excessive resistance .... B .. Require repair or replacement.
Fuse blown .............. A ............ Require replacement.
Fusible link blown ...... A ............ Require replacement.
Open .................... A .. Require repair or replacement.
Poor ground ............. A .. Require repair or replacement.
Routed incorrectly ...... B .. Require rerouting according to
vehicle manufacturer's
specifications.
Shorted ................. A .. Require repair or replacement.
Terminal bent ........... A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal corroded ....... A .. Require repair or replacement.
Terminal loose .......... A .. Require repair or replacement.
\
\
\
\
\
\
\
BALL JOINTS
Before requiring or suggesting ball joint replacement, the
approved OEM procedure must be used to measure ball joint wear. The
measurement(s) obtained, along with the vehicle manufacturer's
specifications, must be noted on the inspection report. Some states
require that these measurements also appear on the invoice.
NOTE: The term "perceptible movement," defined as any visible
movement in any direction, has been the industry standard
for determining the need for replacement of follower ball
joints. Some vehicle manufacturers are now publishing
specifications for follower ball joints that were
Page 1310 of 1691
WHEEL ALIGNMENT
NOTE: See appropriate SPECIFICATIONS & PROCEDURES article in WHEEL
ALIGNMENT.
WHEEL BEARING ADJUSTMENT
1) Tighten wheel bearing adjusting nut to 30-40 ft. lbs. (41-\
54 N.m) while rotating wheel. Stop rotation, and back off adjusting
nut to release all preload. Retighten nut finger tight.
2) Ensure bearing end play is .001-.003" (.025-.076 mm).
Install nut lock and cotter pin. Coat grease cap inside lightly with
grease, and install cap.
BALL JOINT CHECKING
Ball joints are preloaded. Replace lower ball joint if
vertical movement exceeds .03" (.8 mm). Replace upper ball joint if
movement exceeds .03" (.8 mm).
REMOVAL & INSTALLATION
COIL SPRING
Removal
1) Raise vehicle, and position safety stands under frame.
Remove wheels. Remove brake caliper retainer and brake caliper (if
necessary). Support caliper aside. Disconnect tie rod from steering
knuckle.
2) Disconnect stabilizer bar link from lower control arm. See
Fig. 1 . Support lower suspension arm outboard end with jack. Place
jack under arm in front of shock mount. Remove cotter pin and nut from
lower ball joint stud. Using Ball Joint Breaker (C-4150A), separate
ball joint from steering knuckle.
3) Remove lower shock bolt from suspension arm. Lower jack
and suspension arm until spring tension is relieved. Remove spring and
rubber isolator.
Installation
1) Install rubber isolator on top of spring. Position spring
between upper spring seat and lower suspension arm. Raise suspension
arm with jack, and position shock into suspension arm mount.
2) Install shock bolt and tighten to specification. See
TORQUE SPECIFICATIONS table. Install steering knuckle on lower ball
joint stud. Install lower ball joint stud nut and tighten. See TORQUE
SPECIFICATIONS table. Replace cotter pin, and remove jack. Install
stabilizer bar link on lower suspension arm. Install grommet, retainer
and nut.
3) Install tie rod on steering knuckle, and tighten nut to 65
ft. lbs. (88 N.m). Install brake caliper assembly and rotor. Install
tire and wheel assembly. Remove support, and lower vehicle.
STEERING KNUCKLE
Removal & Installation
1) Raise and support vehicle. Remove wheel and tire assembly.
Remove brake caliper. Remove wheel hub and bearing assembly from
spindle.
2) Remove cotter pin and nut from tie-rod end, and disconnect
tie rod. Remove cotter pins and nut from upper and lower ball joint
Page 1312 of 1691
CAUTION: To avoid damage to threads, bearing and seal, DO NOT allow
inner bearing and seal to contact spindle threads during
removal.
2) Carefully slide rotor from steering knuckle. Remove oil
seal and inner bearing.
Installation
Clean and inspect bearings. Pack or replace bearings as
required. Install inner bearing and oil seal. Carefully install rotor
and outer bearing, washer, and nut. Adjust wheel bearings. See WHEEL
BEARING ADJUSTMENT under ADJUSTMENTS & INSPECTION. To install
remaining components, reverse removal procedure.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Ball Joint Nuts
Lower
Light Duty ............................................. 95 (129)\
Heavy Duty ............................................ 110 (149)\
Upper .................................................... 60 (81)\
Lower Control Arm-To-Crossmember Bolt .................... 145 (196)\
Lower Shock Absorber Mounting Bolt
1998 Models ............................................ 100 (135)\
1999 Models ........................................... 105 (142))\
Stabilizer Bar Bolts/Nuts
Frame End ................................................ 40 (54)\
Link End ................................................. 25 (34)\
Tie Rod End Nut ............................................ 40 (54)\
Upper Ball Joint-To-Control Arm .......................... 125 (169)\
Upper Control Arm Eccentric Cam Bolt ....................... 70 (95)\
Upper Control Arm Pivot Bar To Frame ..................... 150 (203)\
Upper Shock Absorber Mounting Bolt
1998 Models .............................................. 35 (47)\
1999 Models .............................................. 40 (54)\
Wheel Lug Nuts
Tapered (Coned)
1/2"-20 ............................................... 105 (142)\
5/8"-18 ............................................... 200 (271)\
Flat (Flanged) (5/8"-18) ............................... 325 (4\
40)
\
\
\
\
\
\
\
Page 1328 of 1691
![DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SU](/img/12/56915/w960_56915-1327.png "DODGE RAM 1999 Service Repair Manual \
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SU")
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SUSPENSION - WARNING LAMP INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bulb burned out ......... A ............ Require replacement.
Warning light does
not come on during
bulb check ............. .. . Further inspection required to
determine cause.
Warning light flashes ... .. . Further inspection required to
determine cause.
Warning light is
intermittent ........... .. . Further inspection required to
determine cause.
Warning light stays
on after initial
bulb check ............. .. . Further inspection required to
determine cause.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - WIRING HARNESSES
AIR RIDE SUSPENSION - WIRING HARNESS INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Connector bent .......... A .. Require repair or replacement.
Connector broken ........ A .. Require repair or replacement.
Connector loose ......... A .. Require repair or replacement.
Damaged (cut, burned, or
chafed) ................ A .. Require repair or replacement.
Excessive resistance .... B .. Require repair or replacement.
Fuse blown .............. A ............ Require replacement.
Fusible link blown ...... A ............ Require replacement.
Open .................... A .. Require repair or replacement.
Poor ground ............. A .. Require repair or replacement.
Routed incorrectly ...... B .. Require rerouting according to
vehicle manufacturer's
specifications.
Shorted ................. A .. Require repair or replacement.
Terminal bent ........... A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal corroded ....... A .. Require repair or replacement.
Terminal loose .......... A .. Require repair or replacement.
\
\
\
\
\
\
\
BALL JOINTS
Before requiring or suggesting ball joint replacement, the
approved OEM procedure must be used to measure ball joint wear. The
measurement(s) obtained, along with the vehicle manufacturer's
specifications, must be noted on the inspection report. Some states
require that these measurements also appear on the invoice.
NOTE: The term "perceptible movement," defined as any visible
movement in any direction, has been the industry standard
for determining the need for replacement of follower ball
joints. Some vehicle manufacturers are now publishing
specifications for follower ball joints that were
Page 1387 of 1691
FUEL DELIVERY
Fuel Filter/Water Separator
1) A restricted fuel filter/water separator may cause engine
starting problems, prevent engine from accelerating, low power or
White exhaust smoke.
2) When ignition is first turned on, WATER-IN-FUEL (WIF)
warning light should come on for 2 seconds to perform bulb and wiring
circuit test and then go off. WATER-IN-FUEL (WIF) warning light is
located on instrument panel, just below tachometer.
3) If WATER-IN-FUEL (WIF) warning light stays on, water
should be drained from fuel filter/water separator. To drain water
from fuel filter/water separator, ensure engine is not running. Place
drain pan below drain tube at fuel filter/water separator.
4) Rotate handle on drain valve forward, toward front of
vehicle to DRAIN position. Drain valve is located near top of fuel
filter/water separator.
5) If no water exists and a clean flow of diesel fuel exists,
rotate handle on drain valve back to CLOSE position. Go to next step.
If water exists, allow water to drain until clean flow of diesel fuel
exists. Rotate handle on drain valve back to CLOSE position. Go to
next step.
6) Verify fuel filter/water separator has been serviced
according to proper service schedule. See SERVICE & ADJUSTMENT
SPECIFICATIONS - TRUCKS article. Ensure pre-filter was cleaned when
fuel filter/water separator was serviced. Pre-filter is located at
bottom of fuel heater on driver's side of engine. No other testing
information is available from manufacturer.
Fuel Heater
1) Malfunctioning fuel heater may cause excessive wax build-
up in fuel filter/water separator during cold ambient temperatures.
Wax build-up may cause hard starting, prevent engine from
accelerating, low power, or Blue or White smoke.
2) Disconnect electrical connector at fuel heater. Fuel
heater is located in top of fuel filter housing. Using ohmmeter, check
resistance between electrical terminals on fuel heater.
3) Resistance should be about one ohm when fuel is cold, and
about 1000 ohms when fuel is warm. Replace fuel heater if resistance
is not within specification.
NOTE: Fuel heater receives battery voltage from fuel heater relay.
Fuel heater relay is located in Power Distribution Center
(PDC), next to left battery. Refer to PDC lid for relay
location. For testing of fuel heater relay, see RELAYS under
RELAYS & SOLENOIDS. Consult wiring diagram for wiring circuit
testing. See appropriate wiring diagram in WIRING DIAGRAMS
article.
Fuel Transfer Pump Preliminary Inspection
1) Check for restricted or leaking fuel supply line to fuel
transfer pump or fuel return line located on driver's side of engine.
Repair fuel supply line or fuel return line if restricted or leaking.
2) Check for fuel leaking from weep hole on housing of fuel
transfer pump. Replace fuel transfer pump if fuel is leaking from weep
hole. Check fuel transfer pump for output pressure, pressure drop,
supply restriction, and air leaks.
NOTE: Separate pressure tests are necessary because transfer pump
operates at 2 pressure cycles, depending on whether engine is
running or cranking.
Page 1391 of 1691
TRUCKS & RWD VANS article.
Transmission Governor Pressure Sensor (A/T Models)
Transmission governor pressure sensor is located on
transmission valve body. If problem exists in transmission governor
pressure sensor or wiring circuit, a Diagnostic Trouble Code (DTC)
will be stored in Powertrain Control Module (PCM). See appropriate
governor pressure sensor test in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD
VANS article.
Transmission Overdrive Solenoid (A/T Models)
Transmission overdrive solenoid may also be referred to as
overdrive solenoid or 3-4 solenoid. Transmission overdrive solenoid is
located transmission valve body. If problem exists in transmission
overdrive solenoid or wiring circuit, a Diagnostic Trouble Code (DTC)
will be stored in Powertrain Control Module (PCM). See DTC P1740: TCC
OR O/D SOLENOID PERFORMANCE test in SELF-DIAGNOSTICS - JEEP, TRUCKS &
RWD VANS article.
Transmission Relay (A/T Models)
See RELAYS under RELAYS & SOLENOIDS.
Transmission Speed Sensor (A/T Models)
Transmission speed sensor may also be referred to as
transmission output shaft speed sensor. Transmission speed sensor is
located on overdrive case at rear of transmission. Transmission speed
sensor contains a 2-pin connector with a Dark Blue/Black wire and a
Light Green/Black wire. If problem exists in transmission speed sensor
or wiring circuit, a Diagnostic Trouble Code (DTC) will be stored in
Powertrain Control Module (PCM). See DTC P0720: LOW OUTPUT SPEED
SENSOR RPM, ABOVE 15 MPH test in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD
VANS article.
Transmission Temperature Sensor (A/T Models)
Transmission temperature sensor is incorporated into governor
pressure sensor on transmission valve body. If problem exists in
transmission temperature sensor or wiring circuit, a Diagnostic
Trouble Code (DTC) will be stored in Powertrain Control Module (PCM)\
.
See appropriate transmission temperature sensor test in SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
Transmission Torque Converter Clutch Solenoid (A/T Models)
The transmission Torque Converter Clutch (TCC) solenoid is
located on transmission valve body. If problem exists in TCC solenoid
or wiring circuit, a Diagnostic Trouble Code (DTC) will be stored in
Powertrain Control Module (PCM). See DTC P0743: TORQUE CONVERTER
CLUTCH SOLENOID/TRANSMISSION RELAY CIRCUIT test in SELF-DIAGNOSTICS -
JEEP, TRUCKS & RWD VANS article.