transmission DODGE RAM 1999 Service Repair Manual

TIE ROD ENDS (INNER AND OUTER)
TRACK BARS
TRAILING ARMS
WHEEL BEARINGS, RACES AND SEALS
Wheel Alignment
WHEEL ALIGNMENT
Wheels and Tires
TIRES
VALVE STEMS
WHEEL ATTACHMENT HARDWARE
WHEELS (RIMS)
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
1) a Pledge of Assurance to their Customers and 2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-

TIE ROD ENDS (INNER AND OUTER)
TRACK BARS
TRAILING ARMS
WHEEL BEARINGS, RACES AND SEALS
Wheel Alignment
WHEEL ALIGNMENT
Wheels and Tires
TIRES
VALVE STEMS
WHEEL ATTACHMENT HARDWARE
WHEELS (RIMS)
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
1) a Pledge of Assurance to their Customers and 2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-

Fig. 6: Engine Driveability & Automatic Transmission

Fig. 10: Manual Transmission & Clutch

Fig. 1: Locating Powertrain Control Module (PCM)
Courtesy of Chrysler Corp.
ENGINE SENSORS & SWITCHES
SENSORS
Battery Temperature Sensor
1) Battery temperature sensor is snapped into battery tray,
below driver's side battery. Disconnect wiring harness at battery
temperature sensor.
2) Using ohmmeter, check resistance between electrical
terminals on battery temperature sensor. Resistance should be 9000-11,
000 ohms at 75-80
F (25-27C). Replace battery temperature sensor if
resistance is not within specification.
3) If problem exists in battery temperature sensor or wiring
circuit, a Diagnostic Trouble Code (DTC) will be stored in Powertrain
Control Module (PCM). See SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS
article.
Crankshaft Position Sensor
If problem exists in crankshaft position sensor, a Diagnostic
Trouble Code (DTC) will be stored in Powertrain Control Module (PCM)\
.
See appropriate crankshaft position sensor test in SELF-DIAGNOSTICS -
JEEP, TRUCKS & RWD VANS article.
Fuel Heater Temperature Sensor
See FUEL DELIVERY under FUEL SYSTEM.
Intake Manifold Air Temperature Sensor
Intake manifold air temperature sensor is located on top of
intake manifold, behind intake manifold air heater. For testing, see
DTC P0113: INTAKE AIR TEMPERATURE SENSOR VOLTAGE HIGH test in SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
Transmission Governor Pressure Sensor (A/T Models)

See TRANSMISSION under MISCELLANEOUS CONTROLS.
Transmission Speed Sensor (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
Transmission Temperature Sensor (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
Water-In-Fuel (WIF) Sensor
Water-in-fuel sensor is located in bottom of fuel
filter/water separator. Testing information not available from
manufacturer.
SWITCHES
Brake Switch
1) Remove lower panel for access to brake switch. Brake
switch is located on bracket, near top of brake pedal. Disconnect
electrical connector from brake switch. Pull plunger on brake switch
fully outward. See Fig. 2.
2) Using ohmmeter, check for continuity between terminals No.
5 and 6 on brake switch. See Fig. 2. Continuity should exist. If
continuity exists, go to next step. If continuity does not exist,
replace brake switch.
3) Push plunger on brake switch fully inward. Using ohmmeter,
check for continuity between terminals No. 1 and 2, and 3 and 4 on
brake switch. See Fig. 2. Continuity should exist. If continuity does
not exist, replace brake switch.
Fig. 2: Identifying Brake Switch Terminals
Courtesy of Chrysler Corp.
Park/Neutral Switch (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.

Transmission Overdrive Switch (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
RELAYS & SOLENOIDS
RELAYS
A/C Clutch Relay
A/C clutch relay may also be referred to as A/C compressor
clutch relay. A/C clutch relay is located in power distribution center
at driver's side front corner of engine compartment, near battery. If
problem exists in A/C clutch relay or wiring circuit, a Diagnostic
Trouble Code (DTC) will be stored in Powertrain Control Module (PCM)\
.
See DTC P0645 in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
Auto Shutdown (ASD) Relay
ASD relay is located in power distribution center at driver's
side front corner of engine compartment, near battery. If problem
exists in ASD relay or wiring circuit, a Diagnostic Trouble Code (DTC)\
will be stored in Powertrain Control Module (PCM). See SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
Fuel Heater Relay
1) Fuel heater relay is located in Power Distribution Center
(PDC) next to left battery. Refer to PDC lid for relay location.
Remove relay and note terminal identification on relay. See Fig. 3.
2) Using ohmmeter, check resistance between terminals No. 85
and 86 on relay. Resistance should be 70-80 ohms. If resistance is
within specification, go to next step. If resistance is not within
specification, replace relay.
3) Using ohmmeter, ensure continuity exists between terminals
No. 30 and 87A on relay. If continuity exists, go to next step. If no
continuity exists, replace relay.
4) Using ohmmeter, ensure no continuity exists between
terminals No. 30 and 87 on relay. If no continuity exists, go to next
step. If continuity exists, replace relay.
5) Using jumper wires, connect terminal No. 85 to negative
side of 12-volt power source and terminal No. 86 to positive side of
12-volt power source. Using ohmmeter, ensure no continuity now exists
between terminals No. 30 and 87A on relay. If no continuity exists, go
to next step. If continuity exists, replace relay.
CAUTION: DO NOT allow ohmmeter leads to contact terminals No. 85 and
86 on relay when checking resistance.
6) Using ohmmeter, ensure continuity now exists between
terminals No. 30 and 87 on relay. If continuity exists, disconnect
jumper wires from relay. If no continuity exists, replace relay.
NOTE: For additional information on checking wiring circuit for
fuel heater relay, see TEST NTC-1: NO TROUBLE CODE TEST MENU
and TEST NS-SEL: NO START TEST SELECTION in SELF-DIAGNOSTICS
- JEEP, TRUCKS & RWD VANS article.

Fig. 4: Locating Intake Manifold Air Heater Relays
Courtesy of Chrysler Corp.
Transmission Relay (A/T Models)
Transmission relay may be referred to as transmission control
relay or transmission 12-volt supply relay. Transmission relay is
located in power distribution center at driver's side front corner of
engine compartment, near battery. If problem exists in transmission
relay or wiring circuit, a Diagnostic Trouble Code (DTC) will be
stored in Powertrain Control Module (PCM). See DTC P1765: TRANSMISSION\
12-VOLT SUPPLY RELAY CONTROL CIRCUIT test in SELF-DIAGNOSTICS - JEEP,
TRUCKS & RWD VANS article.
SOLENOIDS
Transmission Overdrive Solenoid (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.

Transmission Torque Converter Clutch Solenoid (A/T Models)
See TRANSMISSION under MISCELLANEOUS CONTROLS.
Fig. 5: Locating Fuel System Components
Courtesy of Chrysler Corp.
FUEL SYSTEM

NOTE: A leaking fuel injector or high-pressure fuel line may cause
a rough idle, Black smoke, poor engine performance, poor fuel
economy and fuel knock. Following procedure is for
determining if fuel injector is defective.
WARNING: DO NOT allow diesel fuel to contact hot engine when checking
fuel injector, as high exhaust temperatures could cause a
fire. Use care when working around high-pressure fuel lines,
as fuel is under extreme pressure and could penetrate skin,
causing personal injury. Wear safety goggles and protective
clothing when checking fuel injectors.
Fuel Injector
1) Since a leaking high-pressure fuel line may cause the same
symptoms, check for leaking high-pressure fuel line before checking
fuel injector. To check for a leaking high-pressure fuel line, start
engine and allow engine to idle.
2) Inspect high-pressure fuel lines and connections for signs
of fuel leakage by placing cardboard over high-pressure fuel line and
connection. Note if leak is being detected by fuel being sprayed onto
cardboard. If leak exists, repair leak by tightening high-pressure
fuel line nut to 18 ft. lbs. (24 N.m) or replacing high-pressure fuel
line as necessary. If high-pressure fuel line is replaced, bleed air
from fuel system. See FUEL LINE BLEEDING under FUEL SYSTEM in REMOVAL,
OVERHAUL & INSTALLATION article.
3) To check for defective fuel injector, start and idle
engine. Loosen high-pressure fuel line nut at fuel injector and listen
for a decrease in engine speed. Tighten high-pressure fuel line nut to
18 ft. lbs. (24 N.m).
4) If fuel injector is operating properly, engine idle speed
should decrease when high-pressure fuel line nut is loosened. Repeat
procedure on each fuel injector.
5) If engine idle speed does not decrease, fuel injector is
defective and should be removed and tested with a diesel fuel injector
tester. Replace fuel injector if fuel injector opening (pop) pressure
is not about 4500 psi (316 kg/cm

).
EMISSION SYSTEMS & SUB-SYSTEMS
INTAKE MANIFOLD AIR HEATER SYSTEM
Intake Manifold Air Heater Preheat/Postheat Cycle
For testing information on intake manifold air heater system,
see DTC P0380: INTAKE AIR HEATER RELAY NO. 1 CONTROL CIRCUIT and DTC
P0382: INTAKE AIR HEATER RELAY NO. 2 CONTROL CIRCUIT tests in SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
MISCELLANEOUS CONTROLS
NOTE: Although some controlled devices listed here are not
technically engine performance components, they can affect
driveability if they malfunction.
TRANSMISSION
Park/Neutral Switch (A/T Models)
Park/neutral switch is mounted on transmission case, near
shift lever and contains a 3-pin connector. If problem exists in
park/neutral switch or wiring circuit, a Diagnostic Trouble Code (DTC)\
will be stored in Powertrain Control Module (PCM). See DTC P1899: P/N
SWITCH STUCK IN PARK OR IN GEAR test in SELF-DIAGNOSTICS - JEEP,