ECO mode DODGE RAM 1999 Service Workshop Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 896 of 1691
RADIATOR FAN
WARNING: Keep hands away from radiator fan.
STARTING FLUID USE (TURBO DIESEL)
WARNING: DO NOT USE starting fluids (ether) or flammable liquids to
aid the starting of a Cummins Turbo-Diesel. NEVER pour diesel
fuel, flammable liquids or starting fluids into the air
cleaner canister, air intake or turbocharger housing in an
attempt to start the vehicle. A flash fire may result causing
personal injury.
TIRE CHAINS
CAUTION: Do NOT install tire chains or traction devices on front
wheels of 4x4 models with tires larger than P215/75R15. Do
NOT install tire chains or traction devices on rear wheels of
4x4 models with tires larger than P235/75R15. These tires are
too large for sufficient body clearance with chains or other
traction devices. Tire chains are not allowed on 4x2 vehicles
equipped with P235/70R15 tires or 4x4 vehicles equipped with
31 x 10.50R15 tires.
CAUTION: Do NOT drive for a prolonged period of time on dry pavement.
TURBOCHARGED MODELS (TURBO-DIESEL)
CAUTION: Do not race engine immediately after starting. When
stopping engine, allow engine to idle for approximately 60
seconds before shutting it off. Failure to do so may cause
turbocharger damage due to lack of oil flowing to
the turbocharger bearings.
WARRANTY INFORMATION
CAUTION: Due to the different warranties offered in various regions
and the variety of after-market extended warranties
available, please refer to the warranty package that came
with the vehicle to verify all warranty options.
FUSES & CIRCUIT BREAKERS
Page 917 of 1691
PA R ASIT IC L O AD E XPLA N ATIO N & T E ST P R O CED URES
1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Parasitic Load Explanation & Test Procedures
* PLEASE READ THIS FIRST *
This article is provided for general information only. Not
all procedures apply to all makes and models.
GENERAL INFORMATION
The term Parasitic Load refers to electrical devices that
continue to use or draw current after the ignition switch is turned to
OFF position. This small amount of continuous battery draw is
expressed in milliamps (mA). On Ford Motor Co. and General Motors
vehicles produced after 1980, a typical Parasitic Load should be no
more than 50 milliamps (0.050 amps).
Vehicles produced since 1980 have memory devices that draw
current with ignition off for as long as 20 minutes before shutting
down the Parasitic Drain. When Parasitic Load exceeds normal
specifications, the vehicle may exhibit dead battery and no-start
condition.
Follow test procedure for checking Parasitic Loads to
completion. A brief overview of a suggested test procedure is included
along with some typical Parasitic Load specifications. Refer to the
GENERAL MOTORS PARASITIC LOAD TABLE chart.
TESTING FOR PARASITIC LOAD
INTRODUCTION
CAUTION: Always turn ignition off when connecting or disconnecting
battery cables, battery chargers or jumper cables. DO NOT
turn test switch to OFF position (which causes current to run
through ammeter or vehicle electrical system).
NOTE: Memory functions of various accessories must be reset after
the battery is reconnected.
The battery circuit must be opened to connect test switch
(shunt) and ammeter into the circuit. When a battery cable is removed,\
timer circuits within the vehicle computer are interrupted and
immediately begin to discharge. If in doubt about the condition of the
ammeter fuse, test it with an ohmmeter prior to beginning test. An
open fuse will show the same reading (00.00) as no parasitic drain.
Begin test sequence with the meter installed and on the 10-amp scale.
Select lower scale to read parasitic draw.
TEST PROCEDURE USING TEST SWITCH
1) Turn ignition off. Remove negative battery terminal cable.
Install Disconnect Tool (J-38758) test switch male end to negative
battery cable. Turn test switch knob to OFF position (current through
meter). Install negative battery cable to the female end of test
switch.
2) Turn test switch knob to ON position (current through
switch). Road test vehicle with vehicle accessories on (radio, air
conditioner, etc.). After road test, turn ignition switch to LOCKED
position and remove key. Connect ammeter terminals to test switch
Page 923 of 1691
INTERCOOLER
NOTE: Intercooler may also be referred to as charge air cooler.
CAUTION: If vehicle had a turbocharger failure, or for any reason oil
was discharged into the intercooler, intercooler must be
removed and cleaned.
Removal
1) Remove front bumper. Remove front support bracket located
above center of intercooler. On A/C-equipped models, discharge A/C
system using approved refrigerant recovery/recycling equipment.
2) Disconnect and plug hoses and openings at condenser.
Remove condenser-to-intercooler screws and nuts. Remove condenser from
front of intercooler. Plug all openings on condenser.
3) On all models, remove intercooler inlet and outlet ducts.
See Fig. 2 . Remove intercooler bolts. Pivot intercooler forward and
upward to remove.
Inspection & Cleaning
1) Inspect intercooler for damaged fins or cracks. Replace
intercooler if damaged.
CAUTION: DO NOT use caustic cleaners to clean intercooler, or
intercooler may be damaged.
2) If intercooler cleaning is required, flush intercooler
with a non-caustic solvent in the opposite direction of normal
airflow. Use soft-faced hammer to lightly tap on end tanks on
intercooler to dislodge any trapped material.
3) Continue flushing intercooler until all material is
removed from intercooler. Use light to inspect inside of intercooler
for remaining material.
4) Once intercooler is clean, wash intercooler with soap and
hot water to remove remaining solvent. Once remaining solvent is
removed, use clean water to rinse intercooler. Blow compressed air
into intercooler in the opposite direction of the normal airflow until
intercooler is dry.
Installation
To install, reverse removal procedure. Tighten fasteners to
specification. See TORQUE SPECIFICATIONS. On A/C-equipped models,
evacuate and charge A/C system.
Fig. 2: Exploded View Of Intercooler & Components
Courtesy of Chrysler Corp.
TURBOCHARGER
Page 969 of 1691
pulley for the accessory drive belt, as these bolts are under
tension. If necessary to remove these bolts, accessory drive
belt must be removed first.
2) Remove ignition coil retaining bolts or nuts with ignition
coil from the ignition coil mounting bracket. On 3.9L, 5.2L and 5.9L
with light-duty emissions, DO NOT remove ignition coil-to-cylinder
head mounting bracket bolts, as these bolts are under tension. On all
applications, to install, reverse removal procedure. Tighten ignition
coil retaining bolts or nuts to specification. See TORQUE
SPECIFICATIONS.
Removal & Installation (Ram Pickup 8.0L)
1) Two separate ignition coils are located above passenger's
side valve cover. Each ignition coil can be serviced separately. On
all ignition coil applications, disconnect spark plug wires and
electrical connector from ignition coil.
2) Remove ignition coil retaining bolts and ignition coil
from ignition coil mounting bracket. To install, reverse removal
procedure. Ensure ignition coil is mounted on ignition coil mounting
bracket with electrical connector facing downward. Tighten ignition
coil retaining bolts to specification. See TORQUE SPECIFICATIONS.
FUEL SYSTEM
FUEL SYSTEM PRESSURE RELEASE
WARNING: Always release fuel pressure before disconnecting any fuel
injection-related component. DO NOT allow fuel to contact
engine or electrical components.
1) Remove fuel cap from fuel tank. Note location of spring
loaded flapper valve inside fuel tank filler tube assembly. Flapper
valve is located just below the fuel cap area on fuel tank filler tube
assembly. Flapper valve is used as a secondary way of sealing the fuel
tank if fuel cap was not properly tightened.
WARNING: When opening flapper valve inside fuel tank filler tube
assembly, ensure a non-metallic object is used to prevent any
sparks.
2) Using a non-metallic object, push flapper valve inside
filler tube assembly downward to release any pressure from the fuel
tank. Ensure all pressure is released from fuel tank.
3) Remove fuel pump relay from Power Distribution Center
(PDC). Fuel pump relay may be identified by label on inside of PDC
cover. See POWER DISTRIBUTION CENTER (PDC) LOCATION table.
4) On all models, start engine and allow engine to idle until
engine stalls. Attempt to restart engine until engine will no longer
run. Turn ignition off.
CAUTION: Ensure steps 1) through 4) are performed before proceeding.
Steps 3) and 4) must be performed to ensure most of the fuel
pressure is released from fuel rails to prevent an excessive
amount of fuel being delivered into the cylinders.
5) Remaining fuel pressure is released by energizing a fuel
injector. Disconnect electrical connector at any fuel injector.
6) Connect jumper wire between one electrical terminal on
fuel injector and positive battery terminal. Connect another jumper
wire on remaining electrical terminal on fuel injector.
Page 1027 of 1691
![DODGE RAM 1999 Service Workshop Manual \
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark](/img/12/56915/w960_56915-1026.png "DODGE RAM 1999 Service Workshop Manual \
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark")
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
Manual NV4500 4 Qts. (3.8L)
Transmission
Fluid
\
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 248 7.6 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\
Transfer Case NV241 HD 6.5 Pts. (3.1L)
Fluid
\
\
\
\
\
\
\
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant
\
\
\
\
\
\
\
Refrigerant A/C System Capacity 7.75 Oz. (230ML)
Oil
\
\
\
\
\
\
\
Fuel Tank Capacity 35 Gal. (132L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
Page 1053 of 1691
![DODGE RAM 1999 Service Workshop Manual Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\](/img/12/56915/w960_56915-1052.png "DODGE RAM 1999 Service Workshop Manual Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\")
Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\
Model 267 (2WD) 7 Pts. (3.3L)
\
\
\
\
\
Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 248 (2WD) 6.3 Pts. (3L)
Limited Slip
\
\
\
\
\
Differential Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\
Model 267 (2WD) 7 Pts. (3.3L)
\
\
\
\
\
Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 216 6.8 Pts. (3.6L)
Lubricant
\
\
\
\
\
Model 248 7.6 Pts. (3.6L)
\
\
\
\
\
\
\
Transfer Case NV231 HD 2.5 Pts. (1.2L)
Fluid
\
\
\
\
\
\
\
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant
\
\
\
\
\
\
\
Refrigerant A/C System Capacity 7.75 Oz. (230ML)
Oil
\
\
\
\
\
\
\
Fuel Tank 119" & 139" Wheelbase Vehicles 26 Gal. (98L)
\
\
\
\
\
All Others 35 Gal. (132L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
MISCELLANEOUS NOTES
* Once a month, check tire pressure and look for unusual wear
or damage.
* Once a month, Inspect battery and clean and tighten
terminals as required.
* Once a month, check fluid levels of coolant reservoir,
brake master cylinder, power steering & transmission.
Add fluids as required.
* Once a month, check all lights and all other electrical items
for correct operation
Page 1059 of 1691
![DODGE RAM 1999 Service Workshop Manual \
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred.](/img/12/56915/w960_56915-1058.png "DODGE RAM 1999 Service Workshop Manual \
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred.")
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 216 6.8 Pts. (3.6L)
Lubricant
\
\
\
\
\
Model 248 7.6 Pts. (3.6L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
15,000 MILE (24,000 KM) SEVERE DUTY SERVICE
15,000 MILE (24,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
Page 1065 of 1691
![DODGE RAM 1999 Service Workshop Manual \
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD)](/img/12/56915/w960_56915-1064.png "DODGE RAM 1999 Service Workshop Manual \
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD)")
\
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 248 7.6 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
27,000 MILE (43,000 KM) SEVERE DUTY SERVICE
27,000 MILE (43,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Page 1070 of 1691
![DODGE RAM 1999 Service Workshop Manual Transmission
Fluid
\
\](/img/12/56915/w960_56915-1069.png "DODGE RAM 1999 Service Workshop Manual Transmission
Fluid
\
\")
Transmission
Fluid
\
\
\
\
\
\
\
Transfer Case All ATF+2 Type 7176
Fluid Or DEXRON III ATF
\
\
\
\
\
\
\
Rear Axle All Mopar Hypoid Lubricant
Lubricant SAE 80W-90
(
2) GL-5 Gear Lube
\
\
\
\
\
\
\
4x4 Front All Mopar Hypoid Lubricant
Axle SAE 80W-90
Lubricant GL-5 Gear Lube
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 248 7.6 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\
Transfer Case NV241 5 Pts. (2.7L)
Fluid
\
\
\
\
\
NV241 HD 6.5 Pts. (3.5L)
\
\
\
\
\
NV241 HD W/PTO 9 Pts. (4.9L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
Page 1076 of 1691
![DODGE RAM 1999 Service Workshop Manual \
\b\
\
\
\b\
\
\
Item Condition](/img/12/56915/w960_56915-1075.png "DODGE RAM 1999 Service Workshop Manual \
\b\
\
\
\b\
\
\
Item Condition")
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
Rear Axle 9-1/4: Drained 4.8 Pts. (2.3L)
Fluid
\
\
\
\
\
Model 248 (2WD) 6.3 Pts. (3L)
\
\
\
\
\
Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\
Model 267 (2WD) 7 Pts. (3.3L)
\
\
\
\
\
Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 248 (2WD) 6.3 Pts. (3L)
Limited Slip
\
\
\
\
\
Differential Model 248 (4WD) 7.3 Pts. (3.4L)
\
\
\
\
\
Model 267 (2WD) 7 Pts. (3.3L)
\
\
\
\
\
Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 216 6.8 Pts. (3.6L)
Lubricant
\
\
\
\
\
Model 248 7.6 Pts. (3.6L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
51,000 MILE (82,000 KM) SEVERE DUTY SERVICE
51,000 MILE (82,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\