brake sensor DODGE RAM 2002 Service Manual PDF
[x] Cancel search | Manufacturer: DODGE, Model Year: 2002, Model line: RAM, Model: DODGE RAM 2002Pages: 2255, PDF Size: 62.07 MB
Page 1781 of 2255
sludge and/or debris. The torque converter should
also be replaced at the same time.
Failure to flush the cooler and lines will result in
recontamination. Flushing applies to auxiliary cool-
ers as well. The torque converter should also be
replaced whenever a failure generates sludge and
debris. This is necessary because normal converter
flushing procedures will not remove all contami-
nants.
STANDARD PROCEDURE
STANDARD PROCEDURE - FLUID LEVEL
CHECK
Low fluid level can cause a variety of conditions
because it allows the pump to take in air along with
the fluid. As in any hydraulic system, air bubbles
make the fluid spongy, therefore, pressures will be
low and build up slowly.
Improper filling can also raise the fluid level too
high. When the transmssion has too much fluid, the
geartrain churns up foam and cause the same condi-
tions which occur with a low fluid level.
In either case, air bubbles can cause overheating
and/or fluid oxidation, and varnishing. This can
interfere with normal valve, clutch, and accumulator
operation. Foaming can also result in fluid escaping
from the transmission vent where it may be mis-
taken for a leak.
Along with fluid level, it is important to check the
condition of the fluid. When the fluid smells burned,
and is contaminated with metal or friction material
particles, a complete transmission recondition is
needed. Be sure to examine the fluid on the dipstick
closely. If there is any doubt about its condition,
drain out a sample for a double check.
After the fluid has been checked, seat the dipstick
fully to seal out water and dirt.
The transmission has a dipstick to check oil level.
It is located on the right side of the engine. Be sure
to wipe all dirt from dipstick handle before removing.
Fluid level is checked with the engine running at
curb idle speed, the transmission in NEUTRAL and
the transmission fluid at normal operating tempera-
ture.The engine should be running at idle
speed for at least one minute, with the vehicle
on level ground.
The transmission fluid level can be checked two
ways.
PROCEDURE ONE
(1) Transmission fluid must be at normal operat-
ing temperature for accurate fluid level check. Drive
vehicle if necessary to bring fluid temperature up to
normal hot operating temperature of 82ÉC (180ÉF).(2) Position vehicle on level surface.
(3) Start and run engine at curb idle speed.
(4) Apply parking brakes.
(5) Shift transmission momentarily into all gear
ranges. Then shift transmission back to NEUTRAL.
(6) Clean top of filler tube and dipstick to keep
dirt from entering tube.
(7) Remove dipstick (Fig. 83) and check fluid level
as follows:
(a) Correct acceptable level is in crosshatch area.
(b) Correct maximum level is to MAX arrow
mark.
(c) Incorrect level is at or below MIN line.
(d) If fluid is low, add only enough MopartAT F
+4, type 9602, to restore correct level. Do not over-
fill.
PROCEDURE TWO
(1) Start engine and apply parking brake.
(2) Shift the transmission into DRIVE for approxi-
mately 2 seconds.
(3) Shift the transmission into REVERSE for
approximately 2 seconds.
(4) Shift the transmission into PARK.
(5) Hook up DRBtscan tool and select engine.
(6) Select sensors.
(7) Read the transmission temperature value.
(8) Compare the fluid temperature value with the
chart.
(9) Adjust transmission fluid level shown on the
dipstick according to the chart (Fig. 84).
NOTE: After adding any fluid to the transmission,
wait a minimum of 2 minutes for the oil to fully
drain from the fill tube into the transmission before
rechecking the fluid level.
(10) Check transmission for leaks.
Fig. 83 Dipstick Fluid Level MarksÐTypical
1 - DIPSTICK
2 - MAXIMUM CORRECT FLUID LEVEL
3 - ACCEPTABLE FLUID LEVEL
21 - 328 AUTOMATIC TRANSMISSION - 47REBR/BE
FLUID AND FILTER (Continued)
Page 2060 of 2255
LEFT FRONT FENDER
REMOVAL
(1) Remove front bumper (Refer to 13 - FRAMES
& BUMPERS/BUMPERS/FRONT BUMPER -
REMOVAL).
(2) Remove air cleaner from wheelhouse (DIESEL
ONLY).
(3) Remove coolant overflow bottle (V-10 ONLY).
(4) Remove battery tray (Refer to 8 - ELECTRI-
CAL/BATTERY SYSTEM/TRAY - REMOVAL).
(5) Remove screws attaching power distribution
center to left wheelhouse (Fig. 14).
(6) Disengage wire harness tie-downs from wheel-
house.
(7) Disconnect wiring harness to headlamp connec-
tor.
(8) Disconnect wiring harness to airbag sensor and
remove airbag sensor from wheelhouse.
(9) Remove bolts attaching anti-lock brake control-
ler to wheelhouse (Fig. 14), if equipped.
(10) Disengage windshield washer tubing tie-
downs from wheelhouse (Fig. 14).
(11) Remove bolts attaching front fender to cowl
reinforcement (Fig. 15).
(12) Remove bolts attaching front fender to radia-
tor closure panel (Fig. 16).
(13) Remove bolts attaching bottom of front fender
to rocker panel lower flange.
(14) Open left door.
(15) Remove bolt attaching front fender to hinge
pillar mounting bracket.
(16) Remove bolts attaching top of fender to radia-
tor closure panel.
(17) Separate left front fender from vehicle.
INSTALLATION
(1) Position left front fender on vehicle.
(2) Install bolts attaching top of fender to radiator
closure panel.
(3) Install bolt attaching front fender to hinge pil-
lar mounting bracket.
(4) Install bolts attaching bottom of front fender to
rocker panel lower flange.
(5) Install bolts attaching front fender to radiator
closure panel.
(6) Install bolts attaching front fender to cowl rein-
forcement.
(7) Secure windshield washer tubing tie-downs to
wheelhouse.
(8) Install anti-lock brake controller to wheel-
house, if equipped.
(9) Install airbag sensor to wheelhouse and con-
nect wiring harness to airbag sensor.
(10) Connect wiring harness to headlamp connec-
tor.
Fig. 14 Left Front Fender Access Components
1 - ABS CONTROLLER
2 - POWER DISTRIBUTION CENTER
3 - BATTERY
4 - FENDER
5 - WINDSHIELD WASHER RESERVOIR
6 - BRAKE MASTER CYLINDER
Fig. 15 Fender to Cowl ReinforcementÐTypical
1 - BOLT
2 - FENDER
3 - FENDERÐTOÐCOWL REINFORCEMENT
BR/BEEXTERIOR 23 - 93
Page 2188 of 2255
(M)Malfunction Indicator Lamp (MIL) illuminated during engine operation if this DTC was recorded
(depending if required by CARB and/or EPA). MIL is displayed as an engine icon on instrument panel.
(G)Generator lamp illuminated
Generic Scan
Tool P-CodeDRB Scan Tool Display Brief Description of DTC
P0509 (M) IAC Motor Sense Circuit High
P0521 Oil Pressure Switch Rationality
P0522 Oil Pressure Voltage Too Low Oil pressure sending unit (sensor) voltage input below the
minimum acceptable voltage.
P0523 Oil Pressure Voltage Too High Oil pressure sending unit (sensor) voltage input above the
maximum acceptable voltage.
P0524 Oil Pressure Too Low Engine oil pressure is low. Engine power derated.
P0545 A/C Clutch Relay Circuit Problem detected in air conditioning clutch relay control
circuit.
P0551 Power Steering Switch Failure Incorrect input state detected for the power steering switch
circuit. PL: High pressure seen at high speed.
P0562 Charging System Voltage Too Low Supply voltage sensed at ECM too low.
P0563 Charging System Voltage Too High Supply voltage sensed at ECM too high.
P0572 Brake Switch Input #1 Signal Missing
P0573 Brake Switch Input #2 Signal Missing
P0575 Cruise Control Switch Voltage Low
P0576 Cruise Control Switch Voltage High
P0577 Cruise Control Switch Voltage High
P0600 PCM Failure SPI Communications No communication detected between co-processors in the
control module.
P0601 (M) Internal Controller Failure Internal control module fault condition (check sum) detected.
P0602 (M) ECM Fueling Calibration Error ECM Internal fault condition detected.
P0604 RAM Check Failure Transmission control module RAM self test fault detected.
-Aisin transmission
P0605 ROM Check Falure Transmission control module ROM self test fault detected
-Aisin transmission
P0606 (M) ECM Failure ECM Internal fault condition detected.
P0615 Starter Relay Control Circuit An open or shorted condition detected in the starter relay
control circuit.
P0622 (G) Generator Field Not Switching Properly An open or shorted condition detected in the generator field
control circuit.
P0645 A/C Clutch Relay Circuit An open or shorted condition detected in the A/C clutch relay
control circuit.
P0700 EATX Controller DTC Present This SBEC III or JTEC DTC indicates that the EATX or Aisin
controller has an active fault and has illuminated the MIL via
a CCD (EATX) or SCI (Aisin) message. The specific fault
must be acquired from the EATX via CCD or from the Aisin
via ISO-9141.
P0703 Brake Switch Stuck Pressed or
ReleasedIncorrect input state detected in the brake switch circuit.
(Changed from P1595)
P0703 Brake Switch Sense Circuit
BR/BEEMISSIONS CONTROL 25 - 9
EMISSIONS CONTROL (Continued)
Page 2218 of 2255
ABS - DESCRIPTION, BRAKES...........5-35
ABS - OPERATION, BRAKES.............5-36
ABS BRAKE SYSTEM - STANDARD
PROCEDURE, BLEEDING................5-36
ABS INDICATOR - DESCRIPTION.........8J-14
ABS INDICATOR - OPERATION..........8J-14
A/C APPLICATION TABLE,
SPECIFICATIONS......................24-7
A/C COMPRESSOR - DESCRIPTION......24-46
A/C COMPRESSOR - DIAGNOSIS AND
TESTING...........................24-47
A/C COMPRESSOR - INSTALLATION......24-48
A/C COMPRESSOR - OPERATION........24-46
A/C COMPRESSOR - REMOVAL.........24-47
A/C COMPRESSOR CLUTCH -
DESCRIPTION.......................24-11
A/C COMPRESSOR CLUTCH -
INSPECTION........................24-15
A/C COMPRESSOR CLUTCH -
INSTALLATION.......................24-15
A/C COMPRESSOR CLUTCH -
OPERATION.........................24-13
A/C COMPRESSOR CLUTCH - REMOVAL . . 24-13
A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-13
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-13
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-17
A/C COMPRESSOR CLUTCH RELAY -
DIAGNOSIS AND TESTING...............24-17
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-18
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-17
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-18
A/C CONDENSER - DESCRIPTION........24-49
A/C CONDENSER - INSTALLATION.......24-50
A/C CONDENSER - OPERATION..........24-49
A/C CONDENSER - REMOVAL...........24-49
A/C EVAPORATOR - DESCRIPTION.......24-53
A/C EVAPORATOR - INSTALLATION......24-53
A/C EVAPORATOR - OPERATION.........24-53
A/C EVAPORATOR - REMOVAL..........24-53
A/C HEATER CONTROL - DIAGNOSIS
AND TESTING.......................24-18
A/C HIGH PRESSURE SWITCH -
DESCRIPTION.......................24-20
A/C HIGH PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-20
A/C HIGH PRESSURE SWITCH -
INSTALLATION.......................24-20
A/C HIGH PRESSURE SWITCH -
OPERATION.........................24-20
A/C HIGH PRESSURE SWITCH -
REMOVAL..........................24-20
A/C LINE COUPLERS - DESCRIPTION.....24-40
A/C LINE COUPLERS - OPERATION......24-41
A/C LINE COUPLERS - STANDARD
PROCEDURE........................24-44
A/C LOW PRESSURE SWITCH -
DESCRIPTION.......................24-21
A/C LOW PRESSURE SWITCH -
DIAGNOSIS AND TESTING.............24-21
A/C LOW PRESSURE SWITCH -
INSTALLATION.......................24-21
A/C LOW PRESSURE SWITCH -
OPERATION
.........................24-21
A/C LOW PRESSURE SWITCH -
REMOVAL
..........................24-21
A/C ORIFICE TUBE - DESCRIPTION
.......24-54
A/C ORIFICE TUBE - INSTALLATION
......24-54
A/C ORIFICE TUBE - OPERATION
........24-54
A/C ORIFICE TUBE - REMOVAL
..........24-54
A/C PERFORMANCE - DIAGNOSIS AND
TESTING
............................24-2
ACCELERATOR PEDAL - INSTALLATION
. . . 14-37
ACCELERATOR PEDAL - REMOVAL
.......14-36
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION
...............14-95
ACCELERATOR PEDAL POSITION
SENSOR - INSTALLATION
..............14-97
ACCELERATOR PEDAL POSITION
SENSOR - OPERATION
................14-95
ACCELERATOR PEDAL POSITION
SENSOR - REMOVAL
..................14-95ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING................7-24,7-27,7-30
ACCUMULATOR - DESCRIPTION.........24-55
ACCUMULATOR - DESCRIPTION . . 21-149,21-319
ACCUMULATOR - INSPECTION . . . 21-150,21-320
ACCUMULATOR - INSTALLATION........24-55
ACCUMULATOR - OPERATION..........24-55
ACCUMULATOR - OPERATION....21-150,21-320
ACCUMULATOR - REMOVAL............24-55
A/C-HEATER CONTROL - DESCRIPTION . . . 24-18
A/C-HEATER CONTROL - INSTALLATION . . . 24-19
A/C-HEATER CONTROL - OPERATION.....24-18
A/C-HEATER CONTROL - REMOVAL......24-19
ACTUATION TEST MODE - DESCRIPTION,
CIRCUIT.............................25-2
ACTUATOR - INSTALLATION, BLEND
DOOR.............................24-25
ACTUATOR - INSTALLATION, HEAT/
DEFROST DOOR.....................24-27
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-72,23-80
ACTUATOR - INSTALLATION, PANEL/
DEFROST DOOR.....................24-27
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-28
ACTUATOR - REMOVAL, BLEND DOOR....24-25
ACTUATOR - REMOVAL, HEAT/DEFROST
DOOR.............................24-26
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-72,
23-80
ACTUATOR - REMOVAL, PANEL/DEFROST
DOOR.............................24-26
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-27
ADAPTER - INSTALLATION, DEFROSTER
AND DEMISTER DUCT.................24-33
ADAPTER - REMOVAL, DEFROSTER AND
DEMISTER DUCT.....................24-33
ADAPTER BRACKET - INSTALLATION,
CAB CHASSIS.......................13-10
ADAPTER BRACKET - REMOVAL, CAB
CHASSIS...........................13-10
ADAPTER HOUSING SEAL - NV4500 -
INSTALLATION.......................21-42
ADAPTER HOUSING SEAL - NV4500 -
REMOVAL..........................21-42
ADAPTER HOUSING SEAL - NV5600 -
INSTALLATION.......................21-85
ADAPTER HOUSING SEAL - NV5600 -
REMOVAL..........................21-85
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-16
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-16
ADDITIVES - STANDARD PROCEDURE,
COOLANT SELECTION..................7-17
ADHESIVE LOCATIONS, SPECIFICATIONS
- STRUCTURAL......................23-44
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-29
ADJUSTER - INSTALLATION, SEAT
TRACK............................23-143
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-29
ADJUSTER - REMOVAL, SEAT TRACK....23-143
ADJUSTER ASSEMBLY - INSTALLATION,
ROCKER ARM........................9-26
ADJUSTER ASSEMBLY - REMOVAL,
ROCKER ARM........................9-26
ADJUSTER ASSY - CLEANING, ROCKER
ARM ..............................9-146
ADJUSTER ASSY - DESCRIPTION,
ROCKER ARM.......................9-145
ADJUSTER ASSY - INSPECTION,
ROCKER ARM.......................9-146
ADJUSTER ASSY - INSTALLATION,
ROCKER ARM...................9-148,9-84
ADJUSTER ASSY - REMOVAL, ROCKER
ARM ..........................9-145,9-84
ADJUSTER KNOB - INSTALLATION,
TURNING LOOP HGT
.................8O-30
ADJUSTER KNOB - REMOVAL, TURNING
LOOP HGT
..........................8O-30
ADJUSTMENT - STANDARD
PROCEDURE, COMPASS VARIATION
......8M-4
ADJUSTMENT, ADJUSTMENTS
. . . 23-101,23-102,
23-103
ADJUSTMENT, ADJUSTMENTS
...........5-30ADJUSTMENT, ADJUSTMENTS...........13-2
ADJUSTMENT, ADJUSTMENTS . . . 21-208,21-380
ADJUSTMENT AND VERIFICATION -
STANDARD PROCEDURE, VALVE LASH....9-141
ADJUSTMENT, BANDS..........21-151,21-321
ADJUSTMENT, CARGO DOOR...........23-78
ADJUSTMENT, CENTER BEARING..........3-8
ADJUSTMENT, FRONT DOOR FORE/AFT . . . 23-69
ADJUSTMENT, FRONT DOOR IN/OUT.....23-70
ADJUSTMENT, FRONT DOOR LATCH......23-73
ADJUSTMENT, FRONT DOOR UP/DOWN . . . 23-70
ADJUSTMENT, PARKING BRAKE SHOES....5-33
ADJUSTMENT, SHIFT LEVER.....21-463,21-500
ADJUSTMENTS - ADJUSTMENT . . 23-101,23-102,
23-103
ADJUSTMENTS - ADJUSTMENT..........5-30
ADJUSTMENTS - ADJUSTMENT..........13-2
ADJUSTMENTS - ADJUSTMENT . . 21-208,21-380
ADJUSTMENTS, FOG LAMP UNIT........8L-13
ADJUSTMENTS, FRONT AXLE - 248FBI....3-19
ADJUSTMENTS, GEAR.................19-18
ADJUSTMENTS, HEADLAMP UNIT.......8L-21
ADJUSTMENTS, REAR AXLE - 248RBI.....3-51
ADJUSTMENTS, REAR AXLE - 267RBI.....3-83
ADJUSTMENTS, REAR AXLE - 286RBI....3-112
ADJUSTMENTS, TRANSMISSION
THROTTLE VALVE CABLE.........21-210,21-382
ADJUSTMENTS, VALVE BODY....21-257,21-428
AIR BLEED - STANDARD PROCEDURE....14-61
AIR CLEANER ELEMENT - INSTALLATION . . 9-130
AIR CLEANER ELEMENT - REMOVAL.....9-129
AIR CONDITIONER - DESCRIPTION,
HEATER .............................24-1
AIR CONDITIONER - OPERATION,
HEATER .............................24-1
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE WITH.......7-76
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE
WITHOUT............................7-77
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITH.............7-73
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITHOUT..........7-76
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-40
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-40
AIR COOLER AND PLUMBING -
CLEANING, CHARGE..................11-19
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE...............11-18
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-19
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE...............11-20
AIR COOLER AND PLUMBING -
OPERATION, CHARGE.................11-18
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE..................11-18
AIR COOLER SYSTEM - LEAKS -
DIAGNOSIS AND TESTING, CHARGE......11-18
AIR DAM - INSTALLATION, FRONT........13-2
AIR DAM - REMOVAL, FRONT...........13-2
AIR EXHAUSTER - INSTALLATION.......23-77
AIR EXHAUSTER - REMOVAL...........23-77
AIR HEATER - DESCRIPTION, INTAKE....14-104
AIR HEATER - INSTALLATION, INTAKE . . . 14-105
AIR HEATER - OPERATION, INTAKE.....14-104
AIR HEATER - REMOVAL, INTAKE.......14-104
AIR HEATER RELAY - DESCRIPTION,
INTAKE............................14-105
AIR HEATER RELAY - INSTALLATION,
INTAKE............................14-106
AIR HEATER RELAY - OPERATION,
INTAKE............................14-105
AIR HEATER RELAY - REMOVAL, INTAKE . 14-106
AIR IN FUEL SYSTEM - DIAGNOSIS AND
TESTING...........................14-60
AIR INJECTION PUMP - DESCRIPTION....25-29
AIR INJECTION PUMP - DIAGNOSIS AND
TESTING...........................25-29
AIR INJECTION PUMP - INSTALLATION . . . 25-30
AIR INJECTION PUMP - OPERATION
.....25-29
AIR INJECTION PUMP - REMOVAL
.......25-30
AIR INJECTION SYSTEM - DESCRIPTION
. . 25-26
AIR INJECTION SYSTEM - OPERATION
....25-28
AIR INJECTION SYSTEM - TORQUE
......25-29
BR/BEINDEX 1
Description Group-Page Description Group-Page Description Group-Page
Page 2219 of 2255
AIR LEAK VACUUM TEST - DIAGNOSIS
AND TESTING, FUEL SYSTEM...........14-57
AIR PUMP FILTER - INSTALLATION......25-30
AIR PUMP FILTER - REMOVAL..........25-30
AIR TESTING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-100,21-272
AIR TO OIL COOLER - INSTALLATION.....7-87
AIR TO OIL COOLER - REMOVAL.........7-86
AIRBAG - ASSEMBLY, DRIVER..........8O-16
AIRBAG - DESCRIPTION, DRIVER........8O-14
AIRBAG - DESCRIPTION, PASSENGER....8O-21
AIRBAG - DISASSEMBLY, DRIVER.......8O-15
AIRBAG - INSTALLATION, DRIVER.......8O-17
AIRBAG - INSTALLATION, PASSENGER . . . 8O-23
AIRBAG - OPERATION, DRIVER.........8O-14
AIRBAG - OPERATION, PASSENGER......8O-21
AIRBAG - REMOVAL, DRIVER...........8O-14
AIRBAG - REMOVAL, PASSENGER.......8O-21
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-6
AIRBAG CONTROL MODULE -
INSTALLATION.......................8O-8
AIRBAG CONTROL MODULE -
OPERATION..........................8O-6
AIRBAG CONTROL MODULE - REMOVAL . . . 8O-7
AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN........8O-4
AIRBAG INDICATOR - DESCRIPTION.......8J-15
AIRBAG INDICATOR - OPERATION.......8J-15
AIRBAG ON/OFF SWITCH -
DESCRIPTION, PASSENGER............8O-23
AIRBAG ON/OFF SWITCH -
INSTALLATION, PASSENGER...........8O-25
AIRBAG ON/OFF SWITCH - OPERATION,
PASSENGER........................8O-24
AIRBAG ON/OFF SWITCH - REMOVAL,
PASSENGER........................8O-24
AIRBAG SYSTEM - DIAGNOSIS AND
TESTING............................8O-4
AIRBAG SYSTEM - SPECIAL TOOLS.......8O-6
AIRBAGS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED.............8O-4
AIRFLOW - DESCRIPTION, HVAC
SYSTEM............................24-30
AJAR SWITCH - DESCRIPTION, DOOR....8L-34
AJAR SWITCH - DIAGNOSIS AND
TESTING, DOOR.....................8L-34
AJAR SWITCH - INSTALLATION, DOOR . . . 8L-35
AJAR SWITCH - REMOVAL, DOOR.......8L-35
ALIGNMENT - DESCRIPTION, WHEEL.......2-1
ALIGNMENT - OPERATION, WHEEL........2-2
ALIGNMENT I.F.S. - STANDARD
PROCEDURES.........................2-3
ALIGNMENT LINK/COIL SUSPENSION -
STANDARD PROCEDURE.................2-5
ALIGNMENT, SPECIAL TOOLS -
HEADLAMP..........................8L-4
ALIGNMENT, SPECIFICATIONS............2-6
ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE........21-114,21-286
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-12
AMBIENT TEMP SENSOR -
INSTALLATION......................8M-13
AMBIENT TEMP SENSOR - OPERATION . . 8M-12
AMBIENT TEMP SENSOR - REMOVAL
....8M-12
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING
.............8M-12
AMPERAGE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP
.................14-10
ANTENNA - DIAGNOSIS AND TESTING
.....8A-5
ANTENNA BODY & CABLE -
DESCRIPTION
........................8A-4
ANTENNA BODY & CABLE -
INSTALLATION
.......................8A-6
ANTENNA BODY & CABLE - OPERATION
. . . 8A-4
ANTENNA BODY & CABLE - REMOVAL
.....8A-6
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL
..................8A-9
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL
..................8A-9
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER
.......................8E-11
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER
.......................8E-12
ANTILOCK BRAKE - OPERATION,
CONTROLLER
.......................8E-11ANTILOCK BRAKE - REMOVAL,
CONTROLLER.......................8E-11
ANTILOCK BRAKES - DIAGNOSIS AND
TESTING............................5-36
A-PILLAR GRAB HANDLE -
INSTALLATION......................23-119
A-PILLAR GRAB HANDLE - REMOVAL . . . 23-119
A-PILLAR TRIM - INSTALLATION.......23-119
A-PILLAR TRIM - REMOVAL...........23-119
A-PILLAR TWEETER SPEAKER -
INSTALLATION.......................8A-19
A-PILLAR TWEETER SPEAKER -
REMOVAL..........................8A-18
APPLICATION TABLE, SPECIFICATIONS -
A/C ................................24-7
APPLIQUE - INSTALLATION........23-63,23-68
APPLIQUE - REMOVAL...........23-63,23-68
ARM / ADJUSTER ASSEMBLY -
INSTALLATION, ROCKER................9-26
ARM / ADJUSTER ASSEMBLY -
REMOVAL, ROCKER...................9-26
ARM / ADJUSTER ASSY - CLEANING,
ROCKER............................9-146
ARM / ADJUSTER ASSY - DESCRIPTION,
ROCKER............................9-145
ARM / ADJUSTER ASSY - INSPECTION,
ROCKER............................9-146
ARM / ADJUSTER ASSY -
INSTALLATION, ROCKER...........9-148,9-84
ARM / ADJUSTER ASSY - REMOVAL,
ROCKER.......................9-145,9-84
ARM - DESCRIPTION, WIPER............8R-11
ARM - INSTALLATION, LOWER
CONTROL.......................2-10,2-20
ARM - INSTALLATION, UPPER
CONTROL.......................2-13,2-19
ARM - INSTALLATION, WIPER..........8R-12
ARM - OPERATION, WIPER............8R-11
ARM - REMOVAL, LOWER CONTROL . . 2-10,2-20
ARM - REMOVAL, UPPER CONTROL . . 2-13,2-19
ARM - REMOVAL, WIPER..............8R-12
ARMREST/CONSOLE - INSTALLATION,
CENTER SEAT......................23-132
ARMREST/CONSOLE - REMOVAL,
CENTER SEAT......................23-132
ARMREST/LATCH COVER -
INSTALLATION, CENTER SEAT.........23-132
ARMREST/LATCH COVER - REMOVAL,
CENTER SEAT......................23-132
ASD AND FUEL PUMP RELAYS -
DIAGNOSIS AND TESTING...............8I-4
ASD SENSE - PCM INPUT - OPERATION....8I-4
ASH RECEIVER - INSTALLATION........23-107
ASH RECEIVER - REMOVAL...........23-107
ASSEMBLY - INSTALLATION,
INSTRUMENT PANEL.................23-117
ASSEMBLY - INSTALLATION, ROCKER
ARM / ADJUSTER.....................9-26
ASSEMBLY - OVERHEAD CONSOLE
ASSEMBLY..........................8M-8
ASSEMBLY - REMOVAL, INSTRUMENT
PANEL............................23-115
ASSEMBLY - REMOVAL, ROCKER ARM /
ADJUSTER...........................9-26
ASSEMBLY, ASSEMBLY - OVERHEAD
CONSOLE...........................8M-8
ASSEMBLY, AXLE VACUUM MOTOR.......3-34
ASSEMBLY, DIAGNOSIS AND
TESTING....................21-122,21-294
ASSEMBLY, DIFFERENTIAL . 3-126,3-38,3-66,3-97
ASSEMBLY, DIFFERENTIAL - POWR-LOK . . . 3-99
ASSEMBLY, DIFFERENTIAL -
TRAC-LOK......................3-129,3-70
ASSEMBLY, DOUBLE CARDAN
UNIVERSAL JOINTS
...................3-11
ASSEMBLY, DRIVER AIRBAG
...........8O-16
ASSEMBLY, FLYWHEEL
.................6-14
ASSEMBLY, FRONT CLUTCH
.....21-162,21-333
ASSEMBLY, FRONT SERVO
......21-164,21-335
ASSEMBLY, GLOVE BOX
..............23-111
ASSEMBLY, HVAC HOUSING
............24-36
ASSEMBLY, INSTRUMENT CLUSTER
......8J-12
ASSEMBLY, MANUAL - NV4500
.........21-21
ASSEMBLY, MANUAL - NV5600
.........21-64
ASSEMBLY, OIL PUMP
.................9-49
ASSEMBLY, OIL PUMP
.........21-169,21-340
ASSEMBLY, OVERDRIVE UNIT
....21-180,21-354ASSEMBLY, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON
RETAINER...................21-193,21-364
ASSEMBLY, PLANETARY GEARTRAIN/
OUTPUT SHAFT...............21-199,21-371
ASSEMBLY, REAR CLUTCH......21-205,21-377
ASSEMBLY, REAR SERVO.......21-207,21-379
ASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-9
ASSEMBLY, TRANSFER CASE - NV241HD . 21-480
ASSEMBLY, TRANSFER CASE - NV241LD . 21-445
ASSEMBLY, VALVE BODY.......21-248,21-420
ASSIST HANDLE - INSTALLATION.......23-124
ASSIST HANDLE - REMOVAL..........23-124
ASSY - CLEANING, ROCKER ARM /
ADJUSTER..........................9-146
ASSY - DESCRIPTION, ROCKER ARM /
ADJUSTER..........................9-145
ASSY - INSPECTION, ROCKER ARM /
ADJUSTER..........................9-146
ASSY - INSTALLATION, ROCKER ARM /
ADJUSTER......................9-148,9-84
ASSY - REMOVAL, ROCKER ARM /
ADJUSTER......................9-145,9-84
AUDIO - DESCRIPTION.................8A-1
AUDIO - DIAGNOSIS AND TESTING.......8A-2
AUDIO - OPERATION...................8A-2
AUDIO SYSTEMS, SPECIAL TOOLS.......8A-4
AUTO. TRANS. - INSTALLATION, DIESEL
WITH..........................8P-12,8P-6
AUTO. TRANS. - REMOVAL, DIESEL
WITH...........................8P-5,8P-9
AUTOMATIC DAY / NIGHT MIRROR -
DESCRIPTION.......................8N-11
AUTOMATIC DAY / NIGHT MIRROR -
INSTALLATION......................8N-13
AUTOMATIC DAY / NIGHT MIRROR -
OPERATION.........................8N-12
AUTOMATIC DAY / NIGHT MIRROR -
REMOVAL..........................8N-13
AUTOMATIC DAY/NIGHT MIRROR -
DIAGNOSIS AND TESTING.............8N-12
AUTOMATIC TRANSMISSION - 46RE -
DESCRIPTION.......................21-89
AUTOMATIC TRANSMISSION - 46RE -
OPERATION.........................21-91
AUTOMATIC TRANSMISSION - 47RE -
DESCRIPTION......................21-261
AUTOMATIC TRANSMISSION - 47RE -
OPERATION........................21-263
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING.......21-268,21-96
AUTOMATIC TRANSMISSION FLUID -
DESCRIPTION.........................0-6
AUTOMATIC TRANSMISSION FLUID -
OPERATION...........................0-6
AXLE - 248FBI - ADJUSTMENTS, FRONT . . . 3-19
AXLE - 248FBI - DESCRIPTION, FRONT....3-14
AXLE - 248FBI - INSTALLATION, FRONT....3-18
AXLE - 248FBI - OPERATION, FRONT......3-14
AXLE - 248FBI - REMOVAL, FRONT.......3-18
AXLE - 248RBI - ADJUSTMENTS, REAR....3-51
AXLE - 248RBI - DESCRIPTION, REAR.....3-46
AXLE - 248RBI - INSTALLATION, REAR....3-51
AXLE - 248RBI - OPERATION, REAR.......3-46
AXLE - 248RBI - REMOVAL, REAR........3-51
AXLE - 267RBI - ADJUSTMENTS, REAR....3-83
AXLE - 267RBI - DESCRIPTION, REAR.....3-78
AXLE - 267RBI - INSTALLATION, REAR....3-82
AXLE - 267RBI - OPERATION, REAR.......3-78
AXLE - 267RBI - REMOVAL, REAR........3-82
AXLE - 286RBI - ADJUSTMENTS, REAR . . . 3-112
AXLE - 286RBI - DESCRIPTION, REAR....3-107
AXLE - 286RBI - INSTALLATION, REAR . . . 3-112
AXLE - 286RBI - OPERATION, REAR......3-108
AXLE - 286RBI - REMOVAL, REAR.......3-112
AXLE - DIAGNOSIS AND
TESTING...............3-108,3-15,3-47,3-80
AXLE - INSTALLATION, DANA 44.....2-20,2-21
AXLE - INSTALLATION, DANA 60.....2-20,2-22
AXLE - INSTALLATION, INTERMEDIATE....3-30
AXLE - REMOVAL, DANA 44.............2-21
AXLE - REMOVAL, DANA 60.............2-21
AXLE, 248FBI - FRONT
.................3-27
AXLE, 248RBI - REAR
..................3-59
AXLE, 267RBI - REAR
..................3-91
AXLE, 286 RBI - REAR
................3-120
AXLE, 286RBI - REAR
.................3-120
2 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page
Page 2220 of 2255
AXLE BEARINGS - INSTALLATION . . . 3-123,3-62,
3-94
AXLE BEARINGS - REMOVAL . . . 3-123,3-62,3-94
AXLE LUBRICATION - DESCRIPTION.......0-5
AXLE SHAFT SEALS - INSTALLATION......3-31
AXLE SHAFT SEALS - REMOVAL.........3-31
AXLE SHAFTS - INSTALLATION . 3-123,3-29,3-62,
3-94
AXLE SHAFTS - INTERMEDIATE -
REMOVAL...........................3-30
AXLE SHAFTS - REMOVAL . 3-123,3-29,3-62,3-94
AXLE, SPECIAL TOOLS - FRONT..........3-27
AXLE VACUUM MOTOR - ASSEMBLY......3-34
AXLE VACUUM MOTOR - DESCRIPTION....3-31
AXLE VACUUM MOTOR - DISASSEMBLY . . . 3-34
AXLE VACUUM MOTOR - INSTALLATION . . . 3-34
AXLE VACUUM MOTOR - OPERATION.....3-31
AXLE VACUUM MOTOR - REMOVAL.......3-34
BACKLITE - INSTALLATION............23-145
BACKLITE - REMOVAL................23-145
BACKLITE LATCH AND KEEPER -
INSTALLATION......................23-146
BACKLITE LATCH AND KEEPER -
REMOVAL.........................23-146
BACKLITE VENT GLASS - INSTALLATION . 23-146
BACKLITE VENT GLASS - REMOVAL.....23-146
BAFFLE - INSTALLATION, HVAC
HOUSING INLET.....................24-36
BAFFLE - REMOVAL, HVAC HOUSING
INLET..............................24-35
BALANCE - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-4
BALL JOINT - DIAGNOSIS AND TESTING,
LOWER.............................2-10
BALL JOINT - DIAGNOSIS AND TESTING,
UPPER..............................2-12
BAND OPERATION - DIAGNOSIS AND
TESTING, AIR TESTING
TRANSMISSION CLUTCH.......21-100,21-272
BANDS - ADJUSTMENT.........21-151,21-321
BANDS - DESCRIPTION.........21-150,21-320
BANDS - OPERATION..........21-151,21-321
BAR - DIAGNOSIS AND TESTING, TRACK . . . 2-24
BAR - INSTALLATION, STABILIZER . . . 2-12,2-23,
2-29
BAR - INSTALLATION, TRACK............2-24
BAR - REMOVAL, STABILIZER . . . 2-12,2-23,2-29
BAR - REMOVAL, TRACK...............2-24
BARRELS - INSTALLATION, PANEL
OUTLET............................24-31
BARRELS - REMOVAL, PANEL OUTLET . . . 24-31
BASE BRAKE, SPECIFICATIONS............5-2
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-5
BASE BRAKES, SPECIAL TOOLS...........5-4
BASE COAT/CLEAR COAT FINISH -
DESCRIPTION......................23-129
BASE COAT/CLEAR COAT FINISH -
OPERATION........................23-129
BATTERIES - STANDARD PROCEDURE,
REMOTE KEYLESS ENTRY
TRANSMITTER.......................8N-8
BATTERY - DESCRIPTION...............8F-7
BATTERY - DIAGNOSIS AND TESTING.....8F-7
BATTERY CABLE - DESCRIPTION........8F-18
BATTERY CABLE - OPERATION..........8F-18
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-19
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY HOLDDOWN - DESCRIPTION
....8F-17
BATTERY HOLDDOWN - INSTALLATION
. . . 8F-18
BATTERY HOLDDOWN - OPERATION
.....8F-17
BATTERY HOLDDOWN - REMOVAL
.......8F-17
BATTERY, SPECIFICATIONS
..............8F-6
BATTERY SYSTEM - CLEANING
...........8F-5
BATTERY SYSTEM - DESCRIPTION
........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING
............................8F-2
BATTERY SYSTEM - INSPECTION
.........8F-6
BATTERY SYSTEM - OPERATION
.........8F-2
BATTERY TEMPERATURE SENSOR -
DESCRIPTION
.......................8F-27
BATTERY TEMPERATURE SENSOR -
INSTALLATION
.......................8F-28
BATTERY TEMPERATURE SENSOR -
OPERATION
.........................8F-27BATTERY TEMPERATURE SENSOR -
REMOVAL..........................8F-27
BATTERY TRAY - DESCRIPTION.........8F-23
BATTERY TRAY - INSTALLATION.........8F-24
BATTERY TRAY - OPERATION...........8F-23
BATTERY TRAY - REMOVAL............8F-23
BEAM INDICATOR - DESCRIPTION, HIGH . . 8J-21
BEAM INDICATOR - DIAGNOSIS AND
TESTING, HIGH......................8J-21
BEAM INDICATOR - OPERATION, HIGH....8J-21
BEARING - ADJUSTMENT, CENTER.........3-8
BEARING - INSTALLATION, CENTER........3-8
BEARING - INSTALLATION, CLUTCH
RELEASE............................6-12
BEARING - INSTALLATION, HUB.......2-17,2-9
BEARING - INSTALLATION, OUTPUT
SHAFT FRONT................21-171,21-342
BEARING - INSTALLATION, OUTPUT
SHAFT REAR.................21-172,21-343
BEARING - INSTALLATION, PILOT........6-14
BEARING - INSTALLATION, PITMAN......19-23
BEARING - REMOVAL, CENTER...........3-8
BEARING - REMOVAL, CLUTCH RELEASE . . . 6-12
BEARING - REMOVAL, HUB..........2-16,2-9
BEARING - REMOVAL, OUTPUT SHAFT
FRONT......................21-171,21-342
BEARING - REMOVAL, OUTPUT SHAFT
REAR.......................21-171,21-343
BEARING - REMOVAL, PILOT..............6-14
BEARING - REMOVAL, PITMAN..........19-22
BEARING AND CRANKSHAFT JOURNAL
CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD........9-158
BEARING CLEARANCE - STANDARD
PROCEDURE, MAIN...................9-159
BEARING FITTING - STANDARD
PROCEDURE, CONNECTING ROD.....9-29,9-87
BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT MAIN........9-31
BEARINGS - DESCRIPTION,
CRANKSHAFT MAIN...................9-31
BEARINGS - INSTALLATION, AXLE . . . 3-123,3-62,
3-94
BEARINGS - INSTALLATION, CAMSHAFT . . 9-157,
9-28,9-86
BEARINGS - INSTALLATION,
CRANKSHAFT MAIN...............9-32,9-88
BEARINGS - INSTALLATION,
DIFFERENTIAL CASE.....3-102,3-129,3-41,3-72
BEARINGS - OPERATION, CRANKSHAFT
MAIN...............................9-31
BEARINGS - REMOVAL, AXLE . . . 3-123,3-62,3-94
BEARINGS - REMOVAL, CAMSHAFT . 9-152,9-27,
9-85
BEARINGS - REMOVAL, CRANKSHAFT
MAIN...........................9-31,9-88
BEARINGS - REMOVAL, DIFFERENTIAL
CASE.................3-102,3-129,3-40,3-72
BEARINGS - STANDARD PROCEDURE,
FITTING CRANKSHAFT MAIN............9-88
BELT / CHAIN COVER(S) -
INSTALLATION, TIMING...........9-110,9-54
BELT / CHAIN COVER(S) - REMOVAL,
TIMING........................9-110,9-53
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE............7-24,7-27,7-30
BELT & RETRACTOR - INSTALLATION,
REAR SEAT.........................8O-26
BELT & RETRACTOR - REMOVAL, REAR
SEAT ..............................8O-26
BELT BUCKLE - INSTALLATION, FRONT
SEAT ..............................8O-20
BELT BUCKLE - INSTALLATION, REAR
SEAT ..............................8O-27
BELT BUCKLE - REMOVAL, FRONT SEAT . . 8O-20
BELT BUCKLE - REMOVAL, REAR SEAT . . . 8O-27
BELT SWITCH - DESCRIPTION, SEAT.....8O-28
BELT SWITCH - DIAGNOSIS AND
TESTING, SEAT......................8O-28
BELT SWITCH - OPERATION, SEAT.......8O-28
BELT TENSIONERS - 5.9L -
DESCRIPTION
........................7-19
BELT TENSIONERS - 5.9L -
INSTALLATION
........................7-20
BELT TENSIONERS - 5.9L - OPERATION
....7-19
BELT TENSIONERS - 5.9L - REMOVAL
.....7-19
BELT TENSIONERS - 5.9L DIESEL -
DESCRIPTION
........................7-23BELT TENSIONERS - 5.9L DIESEL -
INSTALLATION........................7-23
BELT TENSIONERS - 5.9L DIESEL -
OPERATION..........................7-23
BELT TENSIONERS - 5.9L DIESEL -
REMOVAL...........................7-23
BELT TENSIONERS - 8.0L -
DESCRIPTION........................7-20
BELT TENSIONERS - 8.0L -
INSTALLATION........................7-22
BELT TENSIONERS - 8.0L - OPERATION....7-21
BELT TENSIONERS - 8.0L - REMOVAL.....7-21
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT.................8O-29
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT.....................8O-29
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR INNER.................23-153
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR OUTER................23-153
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR INNER.................23-153
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR OUTER................23-153
BELT/CHAIN AND SPROCKETS -
INSTALLATION, TIMING...........9-111,9-55
BELT/CHAIN AND SPROCKETS -
REMOVAL, TIMING...............9-111,9-54
BELTS - 5.9L - INSTALLATION, DRIVE.....7-26
BELTS - 5.9L - REMOVAL, DRIVE.........7-26
BELTS - 5.9L DIESEL - INSTALLATION,
DRIVE..............................7-32
BELTS - 5.9L DIESEL - REMOVAL, DRIVE . . 7-32
BELTS - 8.0L - INSTALLATION, DRIVE.....7-29
BELTS - 8.0L - REMOVAL, DRIVE.........7-29
BENCH - INSTALLATION, SEAT - SPLIT . . 23-134
BENCH - INSTALLATION, SEAT BACK -
SPLIT.............................23-136
BENCH - INSTALLATION, SEAT BACK
COVER - SPLIT.....................23-137
BENCH - INSTALLATION, SEAT CUSHION
COVER - SPLIT.....................23-140
BENCH - INSTALLATION, SEAT TRACK -
SPLIT.............................23-142
BENCH - REMOVAL, SEAT - SPLIT......23-133
BENCH - REMOVAL, SEAT BACK - SPLIT . 23-135
BENCH - REMOVAL, SEAT BACK COVER
- SPLIT...........................23-137
BENCH - REMOVAL, SEAT CUSHION
COVER - SPLIT.....................23-139
BENCH - REMOVAL, SEAT TRACK -
SPLIT.............................23-142
BENCH SEAT - INSTALLATION, SEAT....23-133
BENCH SEAT - INSTALLATION, SEAT
BACK.............................23-135
BENCH SEAT - REMOVAL, SEAT........23-133
BENCH SEAT - REMOVAL, SEAT BACK . . . 23-135
BEZEL - INSTALLATION, CLUSTER......23-108
BEZEL - REMOVAL, CLUSTER..........23-108
BIN - INSTALLATION, CUBBY..........23-109
BIN - INSTALLATION, STORAGE........23-114
BIN - REMOVAL, CUBBY..............23-108
BIN - REMOVAL, STORAGE............23-114
BLADE - DESCRIPTION, WIPER.........8R-12
BLADE - INSTALLATION, WIPER.........8R-13
BLADE - OPERATION, WIPER...........8R-13
BLADE - REMOVAL, WIPER............8R-13
BLEED - STANDARD PROCEDURE, AIR....14-61
BLEEDING - STANDARD PROCEDURE......5-19
BLEEDING - STANDARD PROCEDURE,
MANUAL.............................5-7
BLEEDING - STANDARD PROCEDURE,
MASTER CYLINDER...................5-27
BLEEDING - STANDARD PROCEDURE,
PRESSURE...........................5-8
BLEEDING ABS BRAKE SYSTEM -
STANDARD PROCEDURE................5-36
BLEND DOOR - INSTALLATION..........24-37
BLEND DOOR - REMOVAL.............24-37
BLEND DOOR ACTUATOR -
INSTALLATION.......................24-25
BLEND DOOR ACTUATOR - REMOVAL
....24-25
BLOCK - CLEANING, ENGINE
........9-27,9-85
BLOCK - DESCRIPTION, BLOWER
MOTOR RESISTOR
...................24-23
BLOCK - DESCRIPTION, JUNCTION
....8W-97-6
BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR
............24-23
BR/BEINDEX 3
Description Group-Page Description Group-Page Description Group-Page
Page 2230 of 2255
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..........7-58,7-60,7-62
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-6
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT............21-157,21-327
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-6
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE........21-158,21-329
FLUID CAPACITIES, SPECIFICATIONS.......0-6
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING................21-157,21-327
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-15
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE.......................21-460
FLUID DRAIN/REFILL - STANDARD
PROCEDURE.......................21-497
FLUID INDICATOR - DESCRIPTION,
WASHER...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER...................8J-35
FLUID INDICATOR - OPERATION,
WASHER...........................8J-35
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING.........21-101,21-273
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT.....21-157,
21-327
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE...............................5-15
FLUID LEVEL CHECK - STANDARD
PROCEDURE.................21-157,21-328
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - INSTALLATION,
WASHER............................8R-8
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-7
FLUID LEVEL SWITCH - REMOVAL,
WASHER............................8R-8
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-15
FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY GAP..........23-56
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE.................7-78,7-82,7-84
FLUSHING COOLERS AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE.......7-79,7-82,7-85
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-34
FLYWHEEL - ASSEMBLY................6-14
FLYWHEEL - DIAGNOSIS AND TESTING....6-13
FLYWHEEL - DISASSEMBLY.............6-13
FOG LAMP - DIAGNOSIS AND TESTING . . . 8L-10
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP UNIT - ADJUSTMENTS.......8L-13
FOG LAMP UNIT - INSTALLATION........8L-12
FOG LAMP UNIT - REMOVAL...........8L-12
FORE/AFT - ADJUSTMENT, FRONT DOOR . . 23-69
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . 9-10,9-122,
9-66
FOUR-WHEEL DRIVE INDICATOR -
DIAGNOSIS AND TESTING..............8J-29
FRAME - INSTALLATION, GRILLE........23-92
FRAME - REMOVAL, GRILLE............23-91
FRAME DIMENSION, SPECIFICATIONS.....13-8
FRAME SERVICE, DESCRIPTION..........13-7
FRONT - 2500 - INSTALLATION..........5-23
FRONT - 2500 - REMOVAL
..............5-22
FRONT - 3500 - INSTALLATION
..........5-23
FRONT - 3500 - REMOVAL
..............5-22
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL
............................9-32
FRONT - INSTALLATION
............5-14,5-26FRONT - INSTALLATION...............22-12
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.......................9-160,9-32
FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-7
FRONT - OPERATION, CRANKSHAFT OIL
SEAL...............................9-32
FRONT - REMOVAL................5-11,5-24
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL..........................9-160,9-32
FRONT - REMOVAL, PROPELLER SHAFT....3-6
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 248FBI - ADJUSTMENTS....3-19
FRONT AXLE - 248FBI - DESCRIPTION.....3-14
FRONT AXLE - 248FBI - INSTALLATION....3-18
FRONT AXLE - 248FBI - OPERATION......3-14
FRONT AXLE - 248FBI - REMOVAL........3-18
FRONT AXLE, 248FBI..................3-27
FRONT AXLE, SPECIAL TOOLS...........3-27
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT...............21-171,21-342
FRONT BEARING - REMOVAL, OUTPUT
SHAFT......................21-171,21-342
FRONT BUMPER - INSTALLATION.........13-4
FRONT BUMPER - REMOVAL............13-4
FRONT BUMPER - SPORT -
INSTALLATION........................13-5
FRONT BUMPER - SPORT - REMOVAL......13-5
FRONT CLUTCH - ASSEMBLY....21-162,21-333
FRONT CLUTCH - DESCRIPTION . . 21-160,21-330
FRONT CLUTCH - DISASSEMBLY . 21-161,21-331
FRONT CLUTCH - INSPECTION . . . 21-162,21-332
FRONT CLUTCH - OPERATION . . . 21-160,21-330
FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL SEAL.........9-89
FRONT COVER INSTALLED - REMOVAL,
FRONT OIL SEAL......................9-89
FRONT COVER REMOVED -
INSTALLATION, FRONT OIL SEAL.........9-90
FRONT COVER REMOVED - REMOVAL,
FRONT OIL SEAL......................9-89
FRONT DOOR FORE/AFT - ADJUSTMENT . . 23-69
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL...........23-152
FRONT DOOR INNER BELT
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR INNER BELT
WEATHERSTRIP - REMOVAL...........23-153
FRONT DOOR IN/OUT - ADJUSTMENT....23-70
FRONT DOOR LATCH - ADJUSTMENT.....23-73
FRONT DOOR OUTER BELT
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR OUTER BELT
WEATHERSTRIP - REMOVAL...........23-153
FRONT DOOR SECOND WEATHERSTRIP -
INSTALLATION......................23-154
FRONT DOOR SECOND WEATHERSTRIP -
REMOVAL.........................23-154
FRONT DOOR SPEAKER - INSTALLATION . . 8A-19
FRONT DOOR SPEAKER - REMOVAL.....8A-19
FRONT DOOR UP/DOWN - ADJUSTMENT . . 23-70
FRONT DOOR UPPER CORNER SEAL -
INSTALLATION......................23-154
FRONT DOOR UPPER CORNER SEAL -
REMOVAL.........................23-153
FRONT END SPLASH SHIELDS -
INSTALLATION.......................23-92
FRONT END SPLASH SHIELDS -
REMOVAL..........................23-92
FRONT FASCIA - INSTALLATION
..........13-2
FRONT FASCIA - REMOVAL
..............13-2
FRONT FASCIA - SPORT - INSTALLATION
. . 13-3
FRONT FASCIA - SPORT - REMOVAL
......13-3
FRONT FENDER - INSTALLATION, LEFT
. . . 23-93
FRONT FENDER - INSTALLATION, RIGHT
. . 23-94
FRONT FENDER - REMOVAL, LEFT
.......23-93
FRONT FENDER - REMOVAL, RIGHT
......23-94
FRONT LOWER FASCIA - INSTALLATION
. . . 13-3
FRONT LOWER FASCIA - REMOVAL
.......13-3
FRONT MOUNT - INSTALLATION
....9-174,9-42,
9-98
FRONT MOUNT - REMOVAL
....9-173,9-41,9-97
FRONT OIL SEAL - FRONT COVER
INSTALLED - INSTALLATION
.............9-89FRONT OIL SEAL - FRONT COVER
INSTALLED - REMOVAL................9-89
FRONT OIL SEAL - FRONT COVER
REMOVED - INSTALLATION..............9-90
FRONT OIL SEAL - FRONT COVER
REMOVED - REMOVAL.................9-89
FRONT OUTPUT SHAFT SEAL -
INSTALLATION................21-461,21-498
FRONT OUTPUT SHAFT SEAL -
REMOVAL...................21-461,21-498
FRONT PARKING BRAKE CABLE -
INSTALLATION........................5-30
FRONT PARKING BRAKE CABLE -
REMOVAL...........................5-29
FRONT SEAT BELT BUCKLE -
INSTALLATION......................8O-20
FRONT SEAT BELT BUCKLE - REMOVAL . . 8O-20
FRONT SERVO - ASSEMBLY.....21-164,21-335
FRONT SERVO - CLEANING.....21-164,21-334
FRONT SERVO - DESCRIPTION . . . 21-164,21-334
FRONT SERVO - DISASSEMBLY . . 21-164,21-334
FRONT SERVO - INSPECTION....21-164,21-335
FRONT SERVO - OPERATION....21-164,21-334
FRONT SUSPENSION, SPECIAL TOOLS -
INDEPENDENT.........................2-9
FRONT TOW HOOK - INSTALLATION......13-10
FRONT TOW HOOK - REMOVAL.........13-10
FRONT WHEEL SPEED SENSOR -
DESCRIPTION........................5-38
FRONT WHEEL SPEED SENSOR -
OPERATION...........................5-38
FUEL DELIVERY - SPECIFICATIONS,
TORQUE............................14-4
FUEL DELIVERY SYSTEM -
DESCRIPTION........................14-2
FUEL DELIVERY SYSTEM -
DESCRIPTION, DIESEL................14-55
FUEL DELIVERY SYSTEM - OPERATION....14-2
FUEL DRAIN MANIFOLD - DESCRIPTION . . 14-89
FUEL DRAIN MANIFOLD - INSTALLATION . . 14-90
FUEL DRAIN MANIFOLD - OPERATION....14-89
FUEL DRAIN MANIFOLD - REMOVAL.....14-90
FUEL FILL DOOR - INSTALLATION.......23-95
FUEL FILL DOOR - REMOVAL...........23-95
FUEL FILLER CAP - DESCRIPTION.......25-34
FUEL FILLER CAP - OPERATION.........25-34
FUEL FILLER CAP - REMOVAL/
INSTALLATION.......................25-34
FUEL FILTER - STANDARD
PROCEDURES, WATER DRAINING AT.....14-61
FUEL FILTER / WATER SEPARATOR -
DESCRIPTION.......................14-63
FUEL FILTER / WATER SEPARATOR -
INSTALLATION.......................14-65
FUEL FILTER / WATER SEPARATOR -
OPERATION.........................14-63
FUEL FILTER / WATER SEPARATOR -
REMOVAL..........................14-64
FUEL FILTER/PRESSURE REGULATOR -
DESCRIPTION........................14-5
FUEL FILTER/PRESSURE REGULATOR -
INSTALLATION........................14-7
FUEL FILTER/PRESSURE REGULATOR -
OPERATION..........................14-5
FUEL FILTER/PRESSURE REGULATOR -
REMOVAL...........................14-5
FUEL GAUGE - DESCRIPTION...........8J-19
FUEL GAUGE - OPERATION.............8J-20
FUEL GAUGE SENDING UNIT -
DIAGNOSIS AND TESTING..............14-7
FUEL HEATER - DESCRIPTION
..........14-66
FUEL HEATER - DIAGNOSIS AND
TESTING
...........................14-66
FUEL HEATER - OPERATION
............14-66
FUEL HEATER - REMOVAL/INSTALLATION
. 14-67
FUEL HEATER RELAY - DESCRIPTION
....14-67
FUEL HEATER RELAY - DIAGNOSIS AND
TESTING
...........................14-68
FUEL HEATER RELAY - INSTALLATION
....14-69
FUEL HEATER RELAY - OPERATION
......14-67
FUEL HEATER RELAY - REMOVAL
........14-69
FUEL INDICATOR - DESCRIPTION, LOW
. . . 8J-22
FUEL INDICATOR - OPERATION, LOW
.....8J-22
FUEL INJECTION - SPECIFICATIONS,
TORQUE - GAS
......................14-35
FUEL INJECTION PUMP DATA PLATE,
SPECIFICATIONS
.....................14-77
BR/BEINDEX 13
Description Group-Page Description Group-Page Description Group-Page
Page 2235 of 2255
JOINT MOLDING - REMOVAL, ROOF......23-91
JOINTS - ASSEMBLY, DOUBLE CARDAN
UNIVERSAL..........................3-11
JOINTS - ASSEMBLY, SINGLE CARDAN
UNIVERSAL...........................3-9
JOINTS - DISASSEMBLY, DOUBLE
CARDAN UNIVERSAL..................3-10
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL...................3-8
JOINTS - INSTALLATION, SINGLE
CARDAN UNIVERSAL..................3-35
JOINTS - REMOVAL, SINGLE CARDAN
UNIVERSAL..........................3-34
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD
BEARING AND CRANKSHAFT...........9-158
JUMP STARTING - STANDARD
PROCEDURE..........................0-7
JUNCTION BLOCK - DESCRIPTION.....8W-97-6
JUNCTION BLOCK - DIAGNOSIS AND
TESTING.........................8W-97-7
JUNCTION BLOCK - INSTALLATION....8W-97-8
JUNCTION BLOCK - OPERATION......8W-97-7
JUNCTION BLOCK - REMOVAL........8W-97-7
KEEPER - INSTALLATION, BACKLITE
LATCH ............................23-146
KEEPER - REMOVAL, BACKLITE LATCH . . 23-146
KEY LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH.............19-9
KEY-IN IGNITION SWITCH -
DESCRIPTION........................19-9
KEYLESS ENTRY SYSTEM -
DESCRIPTION, REMOTE................8N-2
KEYLESS ENTRY SYSTEM - DIAGNOSIS
AND TESTING, POWER LOCK &
REMOTE............................8N-5
KEYLESS ENTRY SYSTEM - OPERATION,
REMOTE............................8N-4
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-8
KEYLESS ENTRY TRANSMITTER -
OPERATION, REMOTE..................8N-8
KEYLESS ENTRY TRANSMITTER
BATTERIES - STANDARD PROCEDURE,
REMOTE............................8N-8
KNOB - INSTALLATION, TURNING LOOP
HGT ADJUSTER.....................8O-30
KNOB - REMOVAL, TURNING LOOP HGT
ADJUSTER.........................8O-30
KNUCKLE - INSTALLATION..........2-10,2-19
KNUCKLE - REMOVAL..............2-10,2-19
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION.....................Intro.-1
LAMP - DESCRIPTION, READING........8L-36
LAMP - DESCRIPTION, TAIL............8L-29
LAMP - DIAGNOSIS AND TESTING, FOG . . 8L-10
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, CLEARANCE......8L-7
LAMP - INSTALLATION, DOME..........8L-34
LAMP - INSTALLATION, FOG............8L-11
LAMP - INSTALLATION, LICENSE PLATE . . 8L-22
LAMP - INSTALLATION, MARKER........8L-23
LAMP - INSTALLATION, OUTBOARD
IDENTIFICATION.....................8L-29
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-29
LAMP - INSTALLATION, READING........8L-37
LAMP - INSTALLATION, TAIL...........8L-30
LAMP - INSTALLATION, UNDERHOOD....8L-32
LAMP - INSTALLATION, VANITY.........8L-37
LAMP - OPERATION, READING..........8L-36
LAMP - OPERATION, TAIL..............8L-29
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, CLEARANCE..........8L-7
LAMP - REMOVAL, DOME..............8L-34
LAMP - REMOVAL, FOG...............8L-11
LAMP - REMOVAL, LICENSE PLATE......8L-22
LAMP - REMOVAL, MARKER...........8L-23
LAMP - REMOVAL, OUTBOARD
IDENTIFICATION
.....................8L-28
LAMP - REMOVAL, PARK/TURN SIGNAL
. . 8L-29
LAMP - REMOVAL, READING
...........8L-36
LAMP - REMOVAL, TAIL
...............8L-29
LAMP - REMOVAL, UNDERHOOD
........8L-31LAMP - REMOVAL, VANITY.............8L-37
LAMP AND SWITCH - INSTALLATION,
GLOVE BOX.........................8L-36
LAMP AND SWITCH - REMOVAL, GLOVE
BOX ...............................8L-35
LAMP MIL - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-23
LAMP MIL - OPERATION, MALFUNCTION
INDICATOR.........................8J-23
LAMP MODULE - DESCRIPTION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - INSTALLATION,
DAYTIME RUNNING....................8L-9
LAMP MODULE - OPERATION, DAYTIME
RUNNING............................8L-9
LAMP MODULE - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP SWITCH - DESCRIPTION, BRAKE....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE......................8L-5
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-6
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP UNIT - ADJUSTMENTS, FOG.......8L-13
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, FOG.......8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-22
LAMP UNIT - INSTALLATION, PARK/
TURN SIGNAL.......................8L-29
LAMP UNIT - INSTALLATION, TAIL.......8L-30
LAMP UNIT - INSTALLATION,
UNDERHOOD........................8L-32
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, FOG...........8L-12
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-22
LAMP UNIT - REMOVAL, PARK/TURN
SIGNAL............................8L-29
LAMP UNIT - REMOVAL, TAIL...........8L-30
LAMP UNIT - REMOVAL, UNDERHOOD . . . 8L-32
LAMPS, SPECIFICATIONS - EXTERIOR.....8L-4
LAMPS, SPECIFICATIONS - INTERIOR....8L-33
LASH ADJUSTMENT AND VERIFICATION
- STANDARD PROCEDURE, VALVE.......9-141
LATCH - ADJUSTMENT, FRONT DOOR....23-73
LATCH - INSTALLATION....23-102,23-65,23-73
LATCH - INSTALLATION, SAFETY.......23-104
LATCH - LOWER - INSTALLATION........23-80
LATCH - LOWER - REMOVAL...........23-80
LATCH - REMOVAL........23-102,23-65,23-72
LATCH - REMOVAL, SAFETY...........23-104
LATCH - UPPER - INSTALLATION........23-81
LATCH - UPPER - REMOVAL............23-81
LATCH AND KEEPER - INSTALLATION,
BACKLITE.........................23-146
LATCH AND KEEPER - REMOVAL,
BACKLITE.........................23-146
LATCH HANDLE - INSTALLATION........23-66
LATCH HANDLE - REMOVAL............23-66
LATCH RELEASE CABLE - INSTALLATION . 23-103
LATCH RELEASE CABLE - REMOVAL....23-103
LATCH STRIKER - INSTALLATION . 23-103,23-66,
23-73
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-112
LATCH STRIKER - LOWER -
INSTALLATION
.......................23-82
LATCH STRIKER - LOWER - REMOVAL
....23-82
LATCH STRIKER - REMOVAL
.....23-103,23-66,
23-73
LATCH STRIKER - REMOVAL, GLOVE
BOX
..............................23-111
LATCH STRIKER - UPPER -
INSTALLATION
.......................23-82
LATCH STRIKER - UPPER - REMOVAL
....23-82
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID
....21-101,21-273
LEAK DETECTION PUMP - DESCRIPTION
. . 25-34
LEAK DETECTION PUMP - INSTALLATION
. 25-34
LEAK DETECTION PUMP - OPERATION
....25-34
LEAK DETECTION PUMP - REMOVAL
.....25-34
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE
..............14-2
LEAK VACUUM TEST - DIAGNOSIS AND
TESTING, FUEL SYSTEM AIR
...........14-57LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE . . . 9-64,9-9
LEAKAGE - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD...............9-106,9-50
LEAKAGE - DIAGNOSIS AND TESTING,
POWER STEERING GEAR..............19-16
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-33
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM.........11-18
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-5
LEAKS - DIAGNOSIS AND TESTING,
ENGINE OIL......................9-43,9-99
LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL LINE............14-78
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-43
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-9
LEFT FRONT FENDER - INSTALLATION....23-93
LEFT FRONT FENDER - REMOVAL.......23-93
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID . . 21-157,21-327
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-15
LEVEL - STANDARD PROCEDURE,
ENGINE OIL.........................9-178
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-57
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT................7-16
LEVEL CHECK - STANDARD
PROCEDURE, FLUID...........21-157,21-328
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL..............14-7,14-77
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL..................14-8
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL................14-7,14-77
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL......................14-7
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - INSTALLATION,
WASHER FLUID......................8R-8
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-7
LEVEL SWITCH - REMOVAL, WASHER
FLUID..............................8R-8
LEVER - ADJUSTMENT, SHIFT . . . 21-463,21-500
LEVER - INSTALLATION, GEAR SHIFT.....19-15
LEVER - INSTALLATION, SHIFT . . . 21-462,21-500
LEVER - REMOVAL, GEAR SHIFT........19-14
LEVER - REMOVAL, SHIFT......21-462,21-499
LICENSE PLATE LAMP - INSTALLATION . . . 8L-22
LICENSE PLATE LAMP - REMOVAL.......8L-22
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-22
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-22
LID - INSTALLATION, CENTER CONSOLE . 23-132
LID - REMOVAL, CENTER CONSOLE.....23-131
LIFTERS - CLEANING, HYDRAULIC....9-37,9-92
LIFTERS - INSTALLATION, HYDRAULIC....9-37,
9-92
LIFTERS - REMOVAL, HYDRAULIC....9-37,9-92
LIFTERS/TAPPETS - CLEANING, SOLID....9-164
LIFTERS/TAPPETS - INSPECTION, SOLID . . 9-165
LIFTERS/TAPPETS - INSTALLATION,
SOLID.............................9-165
LIFTERS/TAPPETS - REMOVAL, SOLID....9-164
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - INSTALLATION,
CIGAR...........................8W-97-4
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-3
LINE - INSTALLATION, LIQUID
..........24-52
LINE - INSTALLATION, SUCTION AND
DISCHARGE
.........................24-52
LINE - REMOVAL, LIQUID
..............24-52
LINE - REMOVAL, SUCTION AND
DISCHARGE
.........................24-51
LINE COUPLERS - DESCRIPTION, A/C
....24-40
18 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page
Page 2239 of 2255
OVERHEAD CONSOLE INSTALLATION,
INSTALLATION.......................8M-8
OVERHEAD CONSOLE REMOVAL,
REMOVAL...........................8M-6
OVERHEAD CONSOLE SPECIAL TOOL,
SPECIAL TOOLS......................8M-9
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
ASSEMBLY...................21-193,21-364
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
CLEANING...................21-192,21-364
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DESCRIPTION................21-192,21-363
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DISASSEMBLY................21-192,21-364
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
INSPECTION.................21-193,21-364
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
OPERATION..................21-192,21-363
OVERTEMP INDICATOR - DESCRIPTION,
TRANS.............................8J-31
OVERTEMP INDICATOR - OPERATION,
TRANS.............................8J-31
PAD - INSTALLATION, SILENCER.......23-104
PAD - REMOVAL, SILENCER...........23-104
PAINT CODE - DESCRIPTION..........23-129
PAINT COLOR CODES, SPECIFICATIONS -
2002 BR/BE........................23-129
PAINT TOUCH-UP - DESCRIPTION......23-130
PAN - CLEANING, OIL........9-103,9-179,9-46
PAN - INSPECTION, OIL......9-103,9-179,9-46
PAN - INSTALLATION, OIL....9-103,9-180,9-46
PAN - REMOVAL, OIL........9-102,9-179,9-46
PANEL - INSTALLATION, QUARTER TRIM . 23-128
PANEL - INSTALLATION, TRIM.....23-75,23-84
PANEL - REMOVAL, QUARTER TRIM....23-128
PANEL - REMOVAL, TRIM.........23-75,23-83
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-9
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-9
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT......................23-117
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT......................23-115
PANEL DEMISTER DUCTS -
INSTALLATION, INSTRUMENT...........24-36
PANEL DEMISTER DUCTS - REMOVAL,
INSTRUMENT.......................24-36
PANEL DUCTS - INSTALLATION,
INSTRUMENT.......................24-37
PANEL DUCTS - REMOVAL,
INSTRUMENT.......................24-37
PANEL OUTLET BARRELS -
INSTALLATION.......................24-31
PANEL OUTLET BARRELS - REMOVAL....24-31
PANEL SPEAKER - INSTALLATION, REAR
CAB SIDE..........................8A-20
PANEL SPEAKER - REMOVAL, REAR CAB
SIDE..............................8A-20
PANEL SYSTEM - DESCRIPTION,
INSTRUMENT......................23-105
PANEL SYSTEM - OPERATION,
INSTRUMENT......................23-106
PANEL TOP COVER - INSTALLATION,
INSTRUMENT......................23-113
PANEL TOP COVER - REMOVAL,
INSTRUMENT......................23-113
PANEL TRIM - INSTALLATION, REAR
CLOSURE..........................23-121
PANEL TRIM - REMOVAL, REAR
CLOSURE..........................23-120
PANEL/DEFROST DOOR - INSTALLATION . . 24-38
PANEL/DEFROST DOOR - REMOVAL......24-38
PANEL/DEFROST DOOR ACTUATOR -
INSTALLATION.......................24-27
PANEL/DEFROST DOOR ACTUATOR -
REMOVAL
..........................24-26
PARK BRAKE CABLE - INSTALLATION,
REAR
...............................5-30
PARK BRAKE CABLE - REMOVAL, REAR
. . . 5-29
PARKING BRAKE - DESCRIPTION
.........5-28
PARKING BRAKE - OPERATION
...........5-28PARKING BRAKE CABLE -
INSTALLATION, FRONT.................5-30
PARKING BRAKE CABLE - REMOVAL,
FRONT..............................5-29
PARKING BRAKE SHOES - ADJUSTMENT . . . 5-33
PARK/NEUTRAL POSITION SWITCH -
DIAGNOSIS AND TESTING......21-195,21-367
PARK/NEUTRAL POSITION SWITCH -
INSTALLATION................21-195,21-367
PARK/NEUTRAL POSITION SWITCH -
REMOVAL...................21-195,21-367
PARK/TURN SIGNAL LAMP -
INSTALLATION.......................8L-29
PARK/TURN SIGNAL LAMP - REMOVAL . . . 8L-29
PARK/TURN SIGNAL LAMP UNIT -
INSTALLATION.......................8L-29
PARK/TURN SIGNAL LAMP UNIT -
REMOVAL..........................8L-29
PARTS - STANDARD PROCEDURES,
CLEANING FUEL SYSTEM..............14-61
PASSENGER AIRBAG - DESCRIPTION....8O-21
PASSENGER AIRBAG - INSTALLATION....8O-23
PASSENGER AIRBAG - OPERATION......8O-21
PASSENGER AIRBAG - REMOVAL........8O-21
PASSENGER AIRBAG ON/OFF SWITCH -
DESCRIPTION.......................8O-23
PASSENGER AIRBAG ON/OFF SWITCH -
INSTALLATION......................8O-25
PASSENGER AIRBAG ON/OFF SWITCH -
OPERATION.........................8O-24
PASSENGER AIRBAG ON/OFF SWITCH -
REMOVAL............................8O-24
PASSENGER POWER SEAT SWITCH -
DESCRIPTION.......................8N-20
PASSENGER POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-20
PASSENGER POWER SEAT SWITCH -
INSTALLATION......................8N-21
PASSENGER POWER SEAT SWITCH -
OPERATION.........................8N-20
PASSENGER POWER SEAT SWITCH -
REMOVAL..........................8N-21
PASSENGER SEAT HEATER SWITCH -
DESCRIPTION.......................8G-16
PASSENGER SEAT HEATER SWITCH -
INSTALLATION......................8G-19
PASSENGER SEAT HEATER SWITCH -
OPERATION.........................8G-17
PASSENGER SEAT HEATER SWITCH -
REMOVAL..........................8G-18
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION..................8E-15
PCM - GAS ENGINES - OPERATION......8E-18
PCM INPUT - OPERATION, ASD SENSE.....8I-4
PCM OUTPUT - DESCRIPTION............8I-4
PCM OUTPUT - OPERATION............14-52
PCM OUTPUT - OPERATION.............8I-4
PCV VALVE - 5.9L - DIAGNOSIS AND
TESTING...........................25-36
PEDAL - DESCRIPTION.................5-17
PEDAL - INSTALLATION............5-17,5-29
PEDAL - INSTALLATION, ACCELERATOR . . . 14-37
PEDAL - INSTALLATION, CLUTCH.........6-15
PEDAL - OPERATION...................5-17
PEDAL - REMOVAL................5-17,5-28
PEDAL - REMOVAL, ACCELERATOR......14-36
PEDAL - REMOVAL, CLUTCH............6-15
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR..........14-95
PEDAL POSITION SENSOR -
INSTALLATION, ACCELERATOR..........14-97
PEDAL POSITION SENSOR - OPERATION,
ACCELERATOR.......................14-95
PEDAL POSITION SENSOR - REMOVAL,
ACCELERATOR.......................14-95
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-17
PEDAL POSITION SWITCH - OPERATION,
CLUTCH
.............................6-17
PER MILE, SPECIFICATIONS - TIRE
REVOLUTIONS
........................22-9
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C
........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS
........9-4,9-59
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER
.....................24-6PILOT BEARING - INSTALLATION.........6-14
PILOT BEARING - REMOVAL.............6-14
PINION GEAR/RING GEAR -
INSTALLATION........................3-43
PINION GEAR/RING GEAR - REMOVAL.....3-41
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION..............3-104,3-132,3-75
PINION GEAR/RING GEAR/TONE RING -
REMOVAL.................3-103,3-131,3-73
PINION SEAL - INSTALLATION . . 3-124,3-35,3-63,
3-95
PINION SEAL - REMOVAL . . 3-123,3-35,3-63,3-94
PIPE - 3.9L/5.2L/5.9L - INSPECTION,
EXHAUST............................11-7
PIPE - 3.9L/5.2L/5.9L - INSTALLATION,
EXHAUST............................11-7
PIPE - 3.9L/5.2L/5.9L - REMOVAL,
EXHAUST............................11-7
PIPE - 5.9L DIESEL - INSPECTION,
EXHAUST............................11-9
PIPE - 5.9L DIESEL - INSTALLATION,
EXHAUST............................11-9
PIPE - 5.9L DIESEL - REMOVAL,
EXHAUST............................11-9
PIPE - 5.9L HD/8.0L - INSPECTION,
EXHAUST............................11-8
PIPE - 5.9L HD/8.0L - INSTALLATION,
EXHAUST............................11-8
PIPE - 5.9L HD/8.0L - REMOVAL,
EXHAUST............................11-7
PISTON & CONNECTING ROD -
CLEANING..................9-169,9-39,9-94
PISTON & CONNECTING ROD -
DESCRIPTION...............9-165,9-38,9-93
PISTON & CONNECTING ROD -
INSPECTION.....................9-39,9-94
PISTON & CONNECTING ROD -
INSTALLATION....................9-39,9-94
PISTON & CONNECTING ROD -
REMOVAL..................9-168,9-38,9-94
PISTON FITTING - STANDARD
PROCEDURE.....................9-38,9-93
PISTON GRADING - STANDARD
PROCEDURE........................9-166
PISTON RETAINER - ASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-193,21-364
PISTON RETAINER - CLEANING,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-192,21-364
PISTON RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-192,21-363
PISTON RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-192,21-364
PISTON RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-193,21-364
PISTON RETAINER - OPERATION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-192,21-363
PISTON RING FITTING - STANDARD
PROCEDURE....................9-171,9-39
PISTON RINGS - STANDARD
PROCEDURE, FITTING..................9-95
PISTONS - DESCRIPTION.......21-195,21-367
PISTONS - OPERATION.........21-196,21-367
PITMAN BEARING - INSTALLATION......19-23
PITMAN BEARING - REMOVAL..........19-22
PITMAN SHAFT - INSTALLATION........19-25
PITMAN SHAFT - REMOVAL............19-24
PITMAN SHAFT SEAL - INSTALLATION....19-26
PITMAN SHAFT SEAL - REMOVAL.......19-25
PLANETARY GEARTRAIN/OUTPUT SHAFT
- ASSEMBLY.................21-199,21-371
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DESCRIPTION...............21-197,21-369
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DISASSEMBLY..............21-198,21-369
PLANETARY GEARTRAIN/OUTPUT SHAFT
- INSPECTION
................21-199,21-371
PLANETARY GEARTRAIN/OUTPUT SHAFT
- OPERATION
.................21-197,21-369
PLATE - DESCRIPTION, BODY CODE
....Intro.-4
PLATE - DESCRIPTION, ENGINE DATA
....9-129
PLATE - DESCRIPTION, EQUIPMENT
IDENTIFICATION
....................Intro.-3
22 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page
Page 2240 of 2255
PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-11
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-11
PLATE LAMP - INSTALLATION, LICENSE . . 8L-22
PLATE LAMP - REMOVAL, LICENSE......8L-22
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-22
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-22
PLATE, SPECIFICATIONS - FUEL
INJECTION PUMP DATA...............14-77
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-89
PLATES - REMOVAL, EXTERIOR NAME....23-89
PLUG - CLEANING, SPARK.............8I-20
PLUG - DESCRIPTION, SPARK...........8I-16
PLUG - INSTALLATION, SPARK..........8I-20
PLUG - INSTALLATION, STEERING GEAR
HOUSING...........................19-30
PLUG - OPERATION, SPARK............8I-16
PLUG - REMOVAL, SPARK..............8I-19
PLUG - REMOVAL, STEERING GEAR
HOUSING...........................19-29
PLUG CABLE - DESCRIPTION, SPARK.....8I-20
PLUG CABLE - INSTALLATION, SPARK....8I-21
PLUG CABLE - OPERATION, SPARK.......8I-20
PLUG CABLE - REMOVAL, SPARK........8I-21
PLUG CABLE ORDER, 8.0L V-10 ENGINE
- SPARK .............................8I-3
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK...............8I-3
PLUG CABLES - DIAGNOSIS AND
TESTING, SPARK.....................8I-20
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK.....................8I-17
PLUGS, SPECIFICATIONS - SPARK........8I-3
PLUMBING - CLEANING, CHARGE AIR
COOLER............................11-19
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER........................11-18
PLUMBING - INSPECTION, CHARGE AIR
COOLER............................11-19
PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-20
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-18
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-18
PLUMBING - SERVICE CAUTIONS........24-42
PLUMBING - SERVICE WARNINGS.......24-42
POLISHING - DESCRIPTION, WET
SANDING/BUFFING..................23-130
PORT - DESCRIPTION, REFRIGERANT
SYSTEM SERVICE.....................24-1
PORT - OPERATION, REFRIGERANT
SYSTEM SERVICE.....................24-2
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-95
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-50
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL.................14-97
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL.................14-95
POSITION SENSOR - OPERATION,
THROTTLE..........................14-50
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL.................14-95
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-17
POSITION SWITCH - DIAGNOSIS AND
TESTING, PARK/NEUTRAL.......21-195,21-367
POSITION SWITCH - INSTALLATION,
PARK/NEUTRAL...............21-195,21-367
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-17
POSITION SWITCH - REMOVAL,
PARK/NEUTRAL...............21-195,21-367
POSITIVE CABLE INSTALLATION,
GASOLINE ENGINE...................8F-22
POSITIVE CABLE REMOVAL, GASOLINE
ENGINE
............................8F-21
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE
..............8W-01-8
POWER BRAKE BOOSTER -
INSTALLATION
........................5-19
POWER BRAKE BOOSTER - REMOVAL
.....5-19
POWER DISTRIBUTION - DESCRIPTION
. 8W-97-1POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-8
POWER DISTRIBUTION CENTER -
INSTALLATION...................8W-97-10
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-8
POWER DISTRIBUTION CENTER -
REMOVAL........................8W-97-8
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-17
POWER LOCK & REMOTE KEYLESS
ENTRY SYSTEM - DIAGNOSIS AND
TESTING............................8N-5
POWER LOCK MOTOR - DESCRIPTION....8N-7
POWER LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-7
POWER LOCK MOTOR - OPERATION......8N-7
POWER LOCK SWITCH - DESCRIPTION....8N-8
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-9
POWER LOCK SWITCH - OPERATION......8N-8
POWER LOCKS - DESCRIPTION..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING............................8N-4
POWER LOCKS - OPERATION............8N-3
POWER MIRROR SWITCH -
DESCRIPTION.......................8N-13
POWER MIRROR SWITCH -
INSTALLATION......................8N-14
POWER MIRROR SWITCH - OPERATION . . 8N-13
POWER MIRROR SWITCH - REMOVAL . . . 8N-13
POWER MIRRORS - DESCRIPTION......8N-11
POWER MIRRORS - OPERATION........8N-11
POWER OUTLET - DESCRIPTION.....8W-97-10
POWER OUTLET - DIAGNOSIS AND
TESTING........................8W-97-10
POWER OUTLET - INSTALLATION....8W-97-11
POWER OUTLET - OPERATION.......8W-97-10
POWER OUTLET - REMOVAL........8W-97-11
POWER SEAT SWITCH - DESCRIPTION,
DRIVER............................8N-17
POWER SEAT SWITCH - DESCRIPTION,
PASSENGER........................8N-20
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, DRIVER................8N-17
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, PASSENGER............8N-20
POWER SEAT SWITCH - INSTALLATION,
DRIVER............................8N-18
POWER SEAT SWITCH - INSTALLATION,
PASSENGER........................8N-21
POWER SEAT SWITCH - OPERATION,
DRIVER............................8N-17
POWER SEAT SWITCH - OPERATION,
PASSENGER........................8N-20
POWER SEAT SWITCH - REMOVAL,
DRIVER............................8N-18
POWER SEAT SWITCH - REMOVAL,
PASSENGER........................8N-21
POWER SEAT SYSTEM - DESCRIPTION . . . 8N-16
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING.......................8N-16
POWER SEAT SYSTEM - OPERATION.....8N-16
POWER SEAT TRACK - DESCRIPTION....8N-21
POWER SEAT TRACK - DIAGNOSIS AND
TESTING...........................8N-22
POWER SEAT TRACK - INSTALLATION....8N-22
POWER SEAT TRACK - OPERATION......8N-22
POWER SEAT TRACK - REMOVAL.......8N-22
POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING GEAR LEAKAGE -
DIAGNOSIS AND TESTING.............19-16
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-22
POWER STEERING GEAR,
SPECIFICATIONS
.....................19-21
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE
. . . 19-33
POWER STEERING PUMP, SPECIAL
TOOLS
.............................19-38
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING
..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING
.....19-34POWER WINDOW SWITCH -
DESCRIPTION.......................8N-24
POWER WINDOW SWITCH - DIAGNOSIS
AND TESTING.......................8N-24
POWER WINDOW SWITCH -
INSTALLATION......................8N-26
POWER WINDOW SWITCH - OPERATION . . 8N-24
POWER WINDOW SWITCH - REMOVAL . . . 8N-25
POWER WINDOWS - DESCRIPTION......8N-23
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-23
POWER WINDOWS - OPERATION........8N-23
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-9
POWR-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-99
POWR-LOK - DISASSEMBLY,
DIFFERENTIAL........................3-99
POWR-LOK - DIAGNOSIS AND TESTING . . . 3-99
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING.........................7-4
PRESSURE - DESCRIPTION, HOSES......19-39
PRESSURE - DIAGNOSIS AND TESTING,
BOOST.............................14-93
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION...........9-64,9-9
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL................9-101,9-178,9-45
PRESSURE - DIAGNOSIS AND TESTING,
FUEL TRANSFER PUMP...............14-84
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW.................19-4
PRESSURE - DIAGNOSIS AND TESTING,
TURBOCHARGER BOOST...............11-13
PRESSURE - GAS ENGINES -
SPECIFICATIONS, FUEL SYSTEM.........14-3
PRESSURE - OPERATION, HOSES........19-39
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-8
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-64
PRESSURE CAP - OPERATION,
RADIATOR...........................7-64
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE...................22-7
PRESSURE FUEL LINES - DESCRIPTION,
HIGH..............................14-78
PRESSURE FUEL LINES - OPERATION,
HIGH..............................14-78
PRESSURE GAUGE - DESCRIPTION, OIL . . 8J-25
PRESSURE GAUGE - OPERATION, OIL....8J-25
PRESSURE GAUGES - DIAGNOSIS AND
TESTING............................22-8
PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING, FUEL.........14-2
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION....9-64,9-9
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-3
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-180
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH
..................24-46
PRESSURE RELIEF VALVE - INSPECTION,
OIL
................................9-180
PRESSURE RELIEF VALVE -
INSTALLATION, OIL
...................9-180
PRESSURE RELIEF VALVE - OPERATION,
HIGH
..............................24-47
PRESSURE RELIEF VALVE - REMOVAL,
OIL
................................9-180
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL
...................9-181
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL
......................9-181
PRESSURE SWITCH - DESCRIPTION, A/C
HIGH
..............................24-20
PRESSURE SWITCH - DESCRIPTION, A/C
LOW
..............................24-21
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C HIGH
...................24-20
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C LOW
...................24-21
PRESSURE SWITCH - INSTALLATION,
A/C HIGH
...........................24-20
PRESSURE SWITCH - INSTALLATION,
A/C LOW
...........................24-21
BR/BEINDEX 23
Description Group-Page Description Group-Page Description Group-Page