wiring DODGE RAM 2003 Service Repair Manual

(3) Recover the refrigerant from the refrigerant
system. (Refer to 24 - HEATING & AIR CONDI-
TIONING/PLUMBING - STANDARD PROCEDURE -
REFRIGERANT RECOVERY)
(4) Disconnect the liquid line refrigerant line fit-
ting from the evaporator inlet tube (Fig. 4). (Refer to
24 - HEATING & AIR CONDITIONING/PLUMBING
- STANDARD PROCEDURE - A/C LINE COU-
PLERS)
(5) Disconnect the accumulator inlet tube refriger-
ant line fitting from the evaporator outlet tube.
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - STANDARD PROCEDURE - A/C LINE
COUPLERS) Install plugs in, or tape over all of the
opened refrigerant line fittings.
(6) Drain the engine cooling system(Refer to 7 -
COOLING - STANDARD PROCEDURE).(7) Disconnect the heater hoses from the heater
core tubes. Install plugs in, or tape over the opened
heater core tubes.
(8) Unplug all electrical connectors from the actua-
tors and blower motor.
(9) Remove the nuts from the HVAC housing
mounting studs.
(10) Remove the HVAC housing from inside the
vehicle taking care not to allow any remaining cool-
ant to drain on the vehicles interior.
DISASSEMBLY
(1) Remove the HVAC housing from the vehicle
and place it on the workbench. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/DISTRIBUTION/HVAC
HOUSING - REMOVAL)
(2) Unplug the electrical connectors from each
actuator.
(3) Remove the HVAC assembly wiring harness
from the HVAC case.
(4) Remove the blower motor and blower wheel
unit from the HVAC housing. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/DISTRIBUTION/
BLOWER MOTOR - REMOVAL)
(5) Remove the heater core mounting screws and
carefully remove the heater core assembly(Refer to
24 - HEATING & AIR CONDITIONING/PLUMBING/
HEATER CORE - REMOVAL).
(6) Carefully remove the foam seals from the
heater core and evaporator coil tube mounting flange
of the HVAC housing. If the either seal is deformed
or damaged it must be replaced.
(7) Use a screwdriver to pry off the four snap clips
that help secure the upper and lower HVAC housing
halves together.
(8) Remove the screws that secure the upper and
lower HVAC housing halves together.
(9) Carefully separate the upper HVAC housing
from the lower half.
ASSEMBLY
(1) Assemble the upper HVAC housing half to the
lower half. During assembly, be certain of the follow-
ing.
(a) That each of the mode door pivot shaft ends
and the temperature blend door shafts are properly
engaged in there pivot holes.
(b) That the blower motor is properly indexed
and installed.
(c) If the unit is equipped with air conditioning,
that the evaporator coil tube rubber seal is prop-
erly positioned in the grooves in both the upper
and lower HVAC housing halves.
(d) That the evaporator drain opening is clean.
(e) That the evaporator drain shield is installed
correctly.
Fig. 4 HVAC Housing - Dual Zone Shown (Typical -
Single Zone)
1 - Mounting Nut
2 - Passenger Blend Door Actuator (dual zone)
3 - Mounting Nut
4 - Air Intake Spacer
5 - Recirculation Door Actuator
6 - Recirculation Door Assembly
7 - Driver Side Blend Door Actuator
8 - HVAC Housing
9 - Mounting Screw
10 - Defroster Door Actuator
11 - Panel Actuator
24 - 28 DISTRIBUTIONDR
HVAC HOUSING (Continued)

(2) Install the screws and snap clips that secure
the upper and lower HVAC housing halves to each
other. Tighten the screws to 2.2 N´m (20 in. lbs.).
(3) Install the blower motor and wheel unit in the
HVAC housing. (Refer to 24 - HEATING & AIR CON-
DITIONING/DISTRIBUTION/BLOWER MOTOR -
INSTALLATION)
(4) Install the foam seals on the flanges around
the heater core and evaporator coil tube mounting
flange of the HVAC housing. Repair or replace any
seals as required.
(5) Install the electrical wiring harness for the
acutators. Make sure the wires are routed through
all wiring retainers, replace any retainers that are
damaged or missing.
(6) Connect the wiring harness to each actuator,
making sure each connector is securely attached.
INSTALLATION
WARNING: IF THE VEHICLE IS EQUIPPED WITH AIR
CONDITIONING, REVIEW THE WARNINGS AND
CAUTIONS IN PLUMBING BEFORE PERFORMING
THE FOLLOWING OPERATION. (Refer to 24 - HEAT-
ING & AIR CONDITIONING/PLUMBING - WARNING)
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - CAUTION) (Refer to 24 - HEATING &
AIR CONDITIONING/PLUMBING - CAUTION -
REFRIGERANT HOSES/LINES/TUBES PRECAU-
TIONS)
(1) Position the HVAC housing to the dash panel.
Be certain that the evaporator condensate drain tube
and the housing mounting studs are inserted into
their correct mounting holes.
(2) Install and tighten the nuts onto the HVAC
housing mounting studs. Tighten the nuts to 6.2 N´m
(55 in.lbs.).
(3) Connect the HVAC system electrical connec-
tors.
(4) Unplug or remove the tape from the heater
core tubes. Connect the heater hoses to the heater
core tubes and fill the engine cooling system(Refer to
7 - COOLING/ENGINE - STANDARD PROCE-
DURE).
(5) Unplug or remove the tape from the liquid line
and the evaporator inlet tube fittings. Connect the
liquid line coupler to the evaporator inlet tube. (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMB-
ING - STANDARD PROCEDURE - A/C LINE COU-
PLERS)(6) Evacuate the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM EVACUATE)
(7) Charge the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM CHARGE)
(8) Install the instrument panel in the vehicle(Re-
fer to 23 - BODY/INSTRUMENT PANEL - INSTAL-
LATION).
(9) Connect the battery negative cable.
(10) Start the engine and check for proper opera-
tion of the heating and air conditioning systems.
(11) Run the calibration procedure.
INSTRUMENT PANEL DUCTS
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the HVAC assembly from the vehi-
cle(Refer to 24 - HEATING & AIR CONDITIONING/
DISTRIBUTION/HVAC HOUSING - REMOVAL).
(3) Disasemble the HVAC housing(Refer to 24 -
HEATING & AIR CONDITIONING/DISTRIBUTION/
HVAC HOUSING - DISASSEMBLY).
(4) Remove the panel door actuator from the hous-
ing if not already removed.
(5) With the actuator removed you can take the
door and shift it so that one pivot point will clear the
housing. You can then tilt the door and remove it
from the housing.
INSTALLATION
(1) Take the door and tilt it so one pivot point is
installed. The carfully install the second pivot point.
Check to be sure no binding of the door is occuring,
repair as required.
(2) Reassemble the HVAC housing(Refer to 24 -
HEATING & AIR CONDITIONING/DISTRIBUTION/
HVAC HOUSING - ASSEMBLY).
(3) Install the HVAC assembly into the vehicle(Re-
fer to 24 - HEATING & AIR CONDITIONING/DIS-
TRIBUTION/INSTRUMENT PANEL DUCTS -
INSTALLATION).
(4) Connect the battery negative cable.
DRDISTRIBUTION 24 - 29
HVAC HOUSING (Continued)

EMISSIONS CONTROL
TABLE OF CONTENTS
page page
EMISSIONS CONTROL
DESCRIPTION
DESCRIPTION - STATE DISPLAY TEST
MODE...............................1
DESCRIPTION - CIRCUIT ACTUATION TEST
MODE...............................1
DESCRIPTION - DIAGNOSTIC TROUBLE
CODES..............................1
DESCRIPTION - TASK MANAGER..........1DESCRIPTION - MONITORED SYSTEMS....1
DESCRIPTION - TRIP DEFINITION.........4
DESCRIPTION - COMPONENT MONITORS . . 4
OPERATION
OPERATION..........................4
OPERATION - TASK MANAGER...........5
OPERATION - NON-MONITORED CIRCUITS . . 8
EVAPORATIVE EMISSIONS................10
EMISSIONS CONTROL
DESCRIPTION
DESCRIPTION - STATE DISPLAY TEST MODE
The switch inputs to the Powertrain Control Mod-
ule (PCM) have two recognized states; HIGH and
LOW. For this reason, the PCM cannot recognize the
difference between a selected switch position versus
an open circuit, a short circuit, or a defective switch.
If the State Display screen shows the change from
HIGH to LOW or LOW to HIGH, assume the entire
switch circuit to the PCM functions properly. Connect
the DRB scan tool to the data link connector and
access the state display screen. Then access either
State Display Inputs and Outputs or State Display
Sensors.
DESCRIPTION - CIRCUIT ACTUATION TEST
MODE
The Circuit Actuation Test Mode checks for proper
operation of output circuits or devices the Powertrain
Control Module (PCM) may not internally recognize.
The PCM attempts to activate these outputs and
allow an observer to verify proper operation. Most of
the tests provide an audible or visual indication of
device operation (click of relay contacts, fuel spray,
etc.). Except for intermittent conditions, if a device
functions properly during testing, assume the device,
its associated wiring, and driver circuit work cor-
rectly. Connect the DRB scan tool to the data link
connector and access the Actuators screen.
DESCRIPTION - DIAGNOSTIC TROUBLE CODES
A Diagnostic Trouble Code (DTC) indicates the
PCM has recognized an abnormal condition in the
system.Remember that DTC's are the results of a sys-
tem or circuit failure, but do not directly iden-
tify the failed component or components.
BULB CHECK
Each time the ignition key is turned to the ON
position, the malfunction indicator (check engine)
lamp on the instrument panel should illuminate for
approximately 2 seconds then go out. This is done for
a bulb check.
OBTAINING DTC'S USING DRB SCAN TOOL
(1) Obtain the applicable Powertrain Diagnostic
Manual.
(2) Obtain the DRB Scan Tool.
(3) Connect the DRB Scan Tool to the data link
(diagnostic) connector. This connector is located in
the passenger compartment; at the lower edge of
instrument panel; near the steering column.
(4) Turn the ignition switch on and access the
ªRead Faultº screen.
(5) Record all the DTC's and ªfreeze frameº infor-
mation shown on the DRB scan tool.
(6) To erase DTC's, use the ªErase Trouble Codeº
data screen on the DRB scan tool.Do not erase any
DTC's until problems have been investigated
and repairs have been performed.
DESCRIPTION - TASK MANAGER
The PCM is responsible for efficiently coordinating
the operation of all the emissions-related compo-
nents. The PCM is also responsible for determining if
the diagnostic systems are operating properly. The
software designed to carry out these responsibilities
is call the 'Task Manager'.
DESCRIPTION - MONITORED SYSTEMS
There are new electronic circuit monitors that
check fuel, emission, engine and ignition perfor-
DREMISSIONS CONTROL 25 - 1

REMOVAL
The duty cycle EVAP canister purge solenoid is
located in the engine compartment. It is attached to
the side of the Power Distribution Center (PDC) (Fig.
3).
(1) Disconnect electrical wiring connector at sole-
noid.
(2) Disconnect vacuum harness at solenoid (Fig. 3).
(3) Remove solenoid from mounting bracket.
INSTALLATION
(1) Install solenoid assembly to mounting bracket.
(2) Connect vacuum harness.
(3) Connect electrical connector.
FUEL FILLER CAP
DESCRIPTION
The plastic fuel tank filler tube cap is threaded
onto the end of the fuel fill tube. Certain models are
equipped with a 1/4 turn cap.
OPERATION
The loss of any fuel or vapor out of fuel filler tube
is prevented by the use of a pressure-vacuum fuel fill
cap. Relief valves inside the cap will release fuel tank
pressure at predetermined pressures. Fuel tank vac-
uum will also be released at predetermined values.This cap must be replaced by a similar unit if
replacement is necessary. This is in order for the sys-
tem to remain effective.
CAUTION: Remove fill cap before servicing any fuel
system component to relieve tank pressure. If
equipped with a Leak Detection Pump (LDP), or
NVLD system, the cap must be tightened securely.
If cap is left loose, a Diagnostic Trouble Code (DTC)
may be set.
REMOVAL
REMOVAL/INSTALLATION
If replacement of the 1/4 turn fuel tank filler tube
cap is necessary, it must be replaced with an identi-
cal cap to be sure of correct system operation.
CAUTION: Remove the fuel tank filler tube cap to
relieve fuel tank pressure. The cap must be
removed prior to disconnecting any fuel system
component or before draining the fuel tank.
LEAK DETECTION PUMP
DESCRIPTION
Vehicles equipped with JTEC engine control mod-
ules use a leak detection pump. Vehicles equipped
with NGC engine control modules use an NVLD
pump. Refer to Natural Vacuum - Leak Detection
(NVLD) for additional information.
The evaporative emission system is designed to
prevent the escape of fuel vapors from the fuel sys-
tem (Fig. 4). Leaks in the system, even small ones,
can allow fuel vapors to escape into the atmosphere.
Government regulations require onboard testing to
make sure that the evaporative (EVAP) system is
functioning properly. The leak detection system tests
for EVAP system leaks and blockage. It also performs
self-diagnostics. During self-diagnostics, the Power-
train Control Module (PCM) first checks the Leak
Detection Pump (LDP) for electrical and mechanical
faults. If the first checks pass, the PCM then uses
the LDP to seal the vent valve and pump air into the
system to pressurize it. If a leak is present, the PCM
will continue pumping the LDP to replace the air
that leaks out. The PCM determines the size of the
leak based on how fast/long it must pump the LDP
as it tries to maintain pressure in the system.
Fig. 3 EVAP / DUTY CYCLE PURGE SOLENOID
1 - MOUNTING BRACKET
2 - VACUUM HARNESS
3 - DUTY CYCLE SOLENOID
4 - TEST PORT CAP AND TEST PORT
DREVAPORATIVE EMISSIONS 25 - 13
EVAP/PURGE SOLENOID (Continued)

CUSHION / COVER - FRONT -
INSTALLATION, SEAT.................23-83
CUSHION / COVER - FRONT -
INSTALLATION, SEAT BACK............23-83
CUSHION / COVER - FRONT - REMOVAL,
SEAT ..............................23-83
CUSHION / COVER - FRONT - REMOVAL,
SEAT BACK.........................23-83
CUSHION / COVER - REAR -
INSTALLATION, SEAT.................23-85
CUSHION / COVER - REAR -
INSTALLATION, SEAT BACK............23-85
CUSHION / COVER - REAR - REMOVAL,
SEAT ..............................23-85
CUSHION / COVER - REAR - REMOVAL,
SEAT BACK.........................23-85
CUSHION - INSTALLATION, CENTER
SEAT ..............................23-80
CUSHION - REMOVAL, CENTER SEAT.....23-80
CUSHION COVER - INSTALLATION,
CENTER SEAT.......................23-81
CUSHION COVER - REMOVAL, CENTER
SEAT ..............................23-81
CUSHION FRAME - REAR -
INSTALLATION, SEAT.................23-85
CUSHION FRAME - REAR - REMOVAL,
SEAT ..............................23-85
CUSTOMER PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-9
CV JOINT-INNER - INSTALLATION........3-16
CV JOINT-INNER - REMOVAL............3-16
CV JOINT-OUTER - INSTALLATION........3-13
CV JOINT-OUTER - REMOVAL............3-13
CYLINDER - DESCRIPTION, MASTER......5-19
CYLINDER - DIAGNOSIS AND TESTING,
IGNITION SWITCH AND KEY LOCK.......19-11
CYLINDER - INSTALLATION, KEY........19-12
CYLINDER - INSTALLATION, LOAD
FLOOR SUPPORT....................23-73
CYLINDER - INSTALLATION, LOCK.......23-24
CYLINDER - INSTALLATION, SUPPORT....23-49
CYLINDER - OPERATION, MASTER........5-20
CYLINDER - REMOVAL, KEY............19-12
CYLINDER - REMOVAL, LOAD FLOOR
SUPPORT..........................23-73
CYLINDER - REMOVAL, LOCK...........23-24
CYLINDER - REMOVAL, SUPPORT.......23-48
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-20
CYLINDER BLOCK REFACING -
STANDARD PROCEDURE...............9-312
CYLINDER BORE - DE-GLAZE -
STANDARD PROCEDURE...............9-313
CYLINDER BORE HONING - STANDARD
PROCEDURE..........9-126,9-233,9-360,9-37
CYLINDER BORE REPAIR - STANDARD
PROCEDURE........................9-313
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING....9-182,
9-231,9-359,9-8,9-92
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING . . . 9-182,9-231,9-359,
9-8,9-92
CYLINDER COMPRESSION/LEAKAGE
TESTS - DIAGNOSIS AND TESTING......9-288
CYLINDER HEAD - CLEANING . 9-195,9-300,9-372
CYLINDER HEAD - DESCRIPTION . . 9-106,9-243,
9-298,9-370
CYLINDER HEAD - INSPECTION....9-195,9-301,
9-372
CYLINDER HEAD - INSTALLATION . . 9-195,9-372
CYLINDER HEAD - INSTALLATION, LEFT . . 9-110
CYLINDER HEAD - INSTALLATION,
RIGHT.............................9-111
CYLINDER HEAD - LEFT - INSTALLATION . . . 9-23
CYLINDER HEAD - LEFT - REMOVAL......9-21
CYLINDER HEAD - OPERATION.....9-194,9-243
CYLINDER HEAD - REMOVAL . 9-195,9-298,9-371
CYLINDER HEAD - REMOVAL, LEFT......9-106
CYLINDER HEAD - REMOVAL, RIGHT.....9-108
CYLINDER HEAD - RIGHT -
INSTALLATION
........................9-32
CYLINDER HEAD - RIGHT - REMOVAL
.....9-32
CYLINDER HEAD COVER -
INSTALLATION
.......................9-304
CYLINDER HEAD COVER - REMOVAL
.....9-304
CYLINDER HEAD COVER GASKET -
DESCRIPTION
.......................9-243CYLINDER HEAD COVER GASKET -
OPERATION.........................9-243
CYLINDER HEAD COVER(S) - CLEANING . . 9-245,
9-374
CYLINDER HEAD COVER(S) -
DESCRIPTION..............9-121,9-26,9-373
CYLINDER HEAD COVER(S) -
INSPECTION...................9-245,9-374
CYLINDER HEAD COVER(S) -
INSTALLATION....9-196,9-245,9-27,9-36,9-374
CYLINDER HEAD COVER(S) - REMOVAL . . 9-196,
9-245,9-26,9-35,9-373
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING........................9-20
CYLINDER HEAD GASKET FAILURE -
DIAGNOSIS AND TESTING . . . 9-194,9-243,9-370
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER......5-20
DAM - INSTALLATION, FRONT AIR........13-2
DAM - REMOVAL, FRONT AIR...........13-2
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR . . 9-186,9-232,
9-289,9-361,9-9,9-93
DAMPER - INSPECTION, VIBRATION.....9-335
DAMPER - INSTALLATION..............19-35
DAMPER - INSTALLATION, VIBRATION . . . 9-142,
9-209,9-263,9-335,9-392,9-55
DAMPER - REMOVAL.................19-35
DAMPER - REMOVAL, VIBRATION . . 9-141,9-209,
9-263,9-335,9-392,9-54
DATA LINK CONNECTOR - DESCRIPTION . . . 8E-3
DATA LINK CONNECTOR - OPERATION......8E-3
DATA PLATE - DESCRIPTION, ENGINE....9-297
DAY / NIGHT MIRROR - DESCRIPTION,
AUTOMATIC........................8N-12
DAY / NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC................8N-12
DAY / NIGHT MIRROR - OPERATION,
AUTOMATIC........................8N-12
DAY / NIGHT MIRROR - REMOVAL,
AUTOMATIC........................8N-13
DEFINITION - DESCRIPTION, TRIP........25-4
DEFROST DOOR - INSTALLATION........24-27
DEFROST DOOR - INSTALLATION, FLOOR . 24-30
DEFROST DOOR - REMOVAL...........24-27
DEFROST DOOR - REMOVAL, FLOOR.....24-30
DEFROST DOOR ACTUATOR -
INSTALLATION, FLOOR................24-20
DEFROST DOOR ACTUATOR - REMOVAL,
FLOOR.............................24-19
DEGAS CONTAINER-3.7L/4.7L -
DESCRIPTION, COOLANT...............7-38
DEGAS CONTAINER-3.7L/4.7L -
INSTALLATION, COOLANT...............7-39
DEGAS CONTAINER-3.7L/4.7L -
OPERATION, COOLANT.................7-38
DEGAS CONTAINER-3.7L/4.7L -
REMOVAL, COOLANT..................7-39
DE-GLAZE - STANDARD PROCEDURE,
CYLINDER BORE.....................9-313
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS...............8M-4
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL RESTRAINT
............8O-7
DETECTION ASSY - DESCRIPTION,
NATURAL VAC LEAK
..................25-23
DETECTION ASSY - INSTALLATION,
NATURAL VAC LEAK
..................25-24
DETECTION ASSY - OPERATION,
NATURAL VAC LEAK
..................25-23
DETECTION ASSY - REMOVAL, NATURAL
VAC LEAK
..........................25-24
DETECTION PUMP - DESCRIPTION, LEAK
. 25-13
DETECTION PUMP - INSTALLATION,
LEAK
..............................25-16
DETECTION PUMP - OPERATION, LEAK
. . . 25-14
DETECTION PUMP - REMOVAL, LEAK
....25-16
DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE
........................8W-01-8
DIAGNOSTIC TROUBLE CODES -
DESCRIPTION
........................25-1
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD
...................7-5
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING
......................8W-01-1DIAGRAMS - HYDRAULIC SCHEMATICS,
SCHEMATICS...........21-175,21-355,21-513
DIESEL - CLEANING, RADIATOR - 5.9L....7-60
DIESEL - CLEANING, RADIATOR FAN -
5.9L................................7-41
DIESEL - CLEANING, WATER PUMP -
5.9L................................7-67
DIESEL - DESCRIPTION...............14-73
DIESEL - DESCRIPTION, 5.9L............11-2
DIESEL - DESCRIPTION, BELT
TENSIONERS - 5.9L...................7-24
DIESEL - DESCRIPTION, COOLING
SYSTEM FLOW - 5.9L...................7-2
DIESEL - DESCRIPTION, ENGINE 5.9L....9-282
DIESEL - DESCRIPTION, ENGINE BLOCK
HEATER - 5.9L........................7-43
DIESEL - DESCRIPTION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-52
DIESEL - DESCRIPTION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-55
DIESEL - DESCRIPTION, RADIATOR -
5.9L................................7-59
DIESEL - DESCRIPTION, TRANS COOLER
- 5.9L..............................7-73
DIESEL - DESCRIPTION, WATER PUMP -
5.9L................................7-67
DIESEL - FUEL INJECTOR FIRING ORDER . 14-60
DIESEL - FUEL SYSTEM PRESSURE......14-60
DIESEL - INSPECTION, RADIATOR - 5.9L . . . 7-60
DIESEL - INSPECTION, RADIATOR FAN -
5.9L................................7-41
DIESEL - INSPECTION, TAILPIPE - 5.9L....11-9
DIESEL - INSPECTION, WATER PUMP -
5.9L................................7-68
DIESEL - INSTALLATION...............14-74
DIESEL - INSTALLATION.....19-25,19-30,19-41
DIESEL - INSTALLATION, BELT
TENSIONERS - 5.9L...................7-25
DIESEL - INSTALLATION, DRIVE BELTS -
5.9L................................7-34
DIESEL - INSTALLATION, ENGINE BLOCK
HEATER - 5.9L........................7-44
DIESEL - INSTALLATION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-53
DIESEL - INSTALLATION, EXCEPT........14-22
DIESEL - INSTALLATION, MUFFLER -
5.9L................................11-9
DIESEL - INSTALLATION, RADIATOR -
5.9L................................7-60
DIESEL - INSTALLATION, RADIATOR FAN
- 5.9L..............................7-41
DIESEL - INSTALLATION, TAILPIPE - 5.9L . . 11-9
DIESEL - INSTALLATION, WATER PUMP -
5.9L................................7-68
DIESEL - OPERATION, BELT
TENSIONERS - 5.9L...................7-24
DIESEL - OPERATION, ENGINE BLOCK
HEATER - 5.9L........................7-43
DIESEL - OPERATION, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-52
DIESEL - OPERATION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-55
DIESEL - OPERATION, RADIATOR - 5.9L . . . 7-59
DIESEL - OPERATION, TRANS COOLER -
5.9L................................7-74
DIESEL - OPERATION, WATER PUMP -
5.9L................................7-67
DIESEL - REMOVAL...................14-73
DIESEL - REMOVAL.........19-24,19-30,19-40
DIESEL - REMOVAL, BELT TENSIONERS -
5.9L................................7-25
DIESEL - REMOVAL, DRIVE BELTS - 5.9L . . 7-34
DIESEL - REMOVAL, ENGINE BLOCK
HEATER - 5.9L........................7-43
DIESEL - REMOVAL, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-53
DIESEL - REMOVAL, EXCEPT...........14-20
DIESEL - REMOVAL, MUFFLER - 5.9L.....11-9
DIESEL - REMOVAL, RADIATOR - 5.9L.....7-59
DIESEL - REMOVAL, RADIATOR FAN -
5.9L
................................7-41
DIESEL - REMOVAL, TAILPIPE - 5.9L
......11-9
DIESEL - REMOVAL, WATER PUMP -
5.9L
................................7-67
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS
.......................0-1
DIESEL ENGINE - DIAGNOSIS AND
TESTING
............................11-3
10 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

GOVERNOR - REMOVAL, ELECTRONIC . . 21-198,
21-378
GRAB HANDLE - INSTALLATION,
B-PILLAR...........................23-69
GRAB HANDLE - REMOVAL, B-PILLAR....23-69
GRILLE - INSTALLATION...............23-40
GRILLE - INSTALLATION, COWL.........23-38
GRILLE - REMOVAL..................23-39
GRILLE - REMOVAL, COWL............23-38
GRILLE FRAME - INSTALLATION.........23-40
GRILLE FRAME - REMOVAL............23-40
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO.............................8W-01-10
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-10
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION..................8A-9
GROUNDS - DESCRIPTION, POWER......8E-10
GUIDE SEALS - DESCRIPTION, VALVE . 9-31,9-36
GUIDES - DESCRIPTION, VALVE....9-106,9-197
GUIDES AND SPRINGS - STANDARD
PROCEDURE, VALVES............9-246,9-305
HALF SHAFT - CAUTION................3-11
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-11
HALF SHAFT - INSTALLATION............3-12
HALF SHAFT - REMOVAL...............3-11
HALF SHAFT - SPECIAL TOOLS..........3-12
HALF SHAFT - SPECIFICATIONS..........3-12
HANDLE - INSTALLATION, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - INSTALLATION, B-PILLAR
GRAB..............................23-69
HANDLE - INSTALLATION, EXTERIOR....23-20,
23-30
HANDLE - INSTALLATION, RELEASE.......5-38
HANDLE - REMOVAL, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - REMOVAL, B-PILLAR GRAB....23-69
HANDLE - REMOVAL, EXTERIOR . . . 23-20,23-30
HANDLE - REMOVAL, RELEASE..........5-38
HANDLE ACTUATOR - INSTALLATION,
INSIDE........................23-22,23-32
HANDLE ACTUATOR - REMOVAL, INSIDE . 23-22,
23-31
HANDLE/LATCH REMOTE -
INSTALLATION, RELEASE..............23-17
HANDLE/LATCH REMOTE - REMOVAL,
RELEASE...........................23-17
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING..........................8W-01-7
HAT BRAKE - CLEANING, REAR DRUM
IN .................................5-33
HAT BRAKE - INSPECTION, REAR DRUM
IN .................................5-33
HAZARD SWITCH - DESCRIPTION.......8L-13
HAZARD SWITCH - OPERATION.........8L-13
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION........................5-44
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION..........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL...........................5-44
HD - INSTALLATION, 4X4..............19-15
HD - INSTALLATION, ALL LD & HD
EXCEPT 4X4........................19-15
HD - REMOVAL, 4X4
..................19-14
HD - REMOVAL, ALL LD & HD EXCEPT
4X4
...............................19-14
HD EXCEPT 4X4 HD - INSTALLATION,
ALL LD
............................19-15
HD EXCEPT 4X4 HD - REMOVAL, ALL LD
. 19-14
HEAD - CLEANING, CYLINDER
.....9-195,9-300,
9-372HEAD - DESCRIPTION, CYLINDER . . 9-106,9-243,
9-298,9-370
HEAD - INSPECTION, CYLINDER . . . 9-195,9-301,
9-372
HEAD - INSTALLATION, CYLINDER . . 9-195,9-372
HEAD - INSTALLATION, LEFT CYLINDER . . 9-110
HEAD - INSTALLATION, RIGHT
CYLINDER..........................9-111
HEAD - LEFT - INSTALLATION,
CYLINDER...........................9-23
HEAD - LEFT - REMOVAL, CYLINDER......9-21
HEAD - OPERATION, CYLINDER....9-194,9-243
HEAD - REMOVAL, CYLINDER.....9-195,9-298,
9-371
HEAD - REMOVAL, LEFT CYLINDER......9-106
HEAD - REMOVAL, RIGHT CYLINDER.....9-108
HEAD - RIGHT - INSTALLATION,
CYLINDER...........................9-32
HEAD - RIGHT - REMOVAL, CYLINDER....9-32
HEAD COVER - INSTALLATION,
CYLINDER..........................9-304
HEAD COVER - REMOVAL, CYLINDER....9-304
HEAD COVER GASKET - DESCRIPTION,
CYLINDER..........................9-243
HEAD COVER GASKET - OPERATION,
CYLINDER..........................9-243
HEAD COVER(S) - CLEANING, CYLINDER . 9-245,
9-374
HEAD COVER(S) - DESCRIPTION,
CYLINDER.................9-121,9-26,9-373
HEAD COVER(S) - INSPECTION,
CYLINDER.....................9-245,9-374
HEAD COVER(S) - INSTALLATION,
CYLINDER........9-196,9-245,9-27,9-36,9-374
HEAD COVER(S) - REMOVAL, CYLINDER . 9-196,
9-245,9-26,9-35,9-373
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...................9-20
HEAD GASKET FAILURE - DIAGNOSIS
AND TESTING, CYLINDER....9-194,9-243,9-370
HEAD GASKET SELECTION - STANDARD
PROCEDURE........................9-330
HEADLAMP - INSTALLATION............8L-13
HEADLAMP - REMOVAL...............8L-13
HEADLAMP ALIGNMENT - SPECIAL
TOOLS..............................8L-7
HEADLAMP SWITCH - DESCRIPTION.....8L-14
HEADLAMP SWITCH - INSTALLATION....8L-14
HEADLAMP SWITCH - OPERATION.......8L-14
HEADLAMP SWITCH - REMOVAL........8L-14
HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT PANEL.....23-57
HEADLAMP SWITCH BEZEL - REMOVAL,
INSTRUMENT PANEL..................23-57
HEADLAMP UNIT - ADJUSTMENTS......8L-15
HEADLAMP UNIT - INSTALLATION.......8L-15
HEADLAMP UNIT - REMOVAL...........8L-15
HEADLINER - INSTALLATION...........23-69
HEADLINER - REMOVAL...............23-69
HEADREST - INSTALLATION............23-82
HEADREST - REMOVAL................23-82
HEADREST SLEEVE - INSTALLATION.....23-82
HEADREST SLEEVE - REMOVAL.........23-82
HEAT SHIELDS - DESCRIPTION..........11-7
HEAT SHIELDS - INSTALLATION..........11-8
HEAT SHIELDS - REMOVAL.............11-7
HEAT STAKING - STANDARD
PROCEDURE.........................23-3
HEATED MIRROR SYSTEM -
DESCRIPTION........................8G-1
HEATED MIRROR SYSTEM - DIAGNOSIS
AND TESTING........................8G-2
HEATED MIRROR SYSTEM - OPERATION . . . 8G-1
HEATED SEAT ELEMENT - DESCRIPTION . . . 8G-5
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING........................8G-6
HEATED SEAT ELEMENT - INSTALLATION . . 8G-6
HEATED SEAT ELEMENT - OPERATION.....8G-6
HEATED SEAT ELEMENT - REMOVAL......8G-6
HEATED SEAT MODULE - DESCRIPTION....8E-6
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING........................8E-7
HEATED SEAT MODULE - INSTALLATION
. . . 8E-7
HEATED SEAT MODULE - OPERATION
.....8E-6
HEATED SEAT MODULE - REMOVAL
.......8E-7
HEATED SEAT SENSOR - DESCRIPTION
....8G-7
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING
........................8G-7HEATED SEAT SENSOR - OPERATION.....8G-7
HEATED SEAT SENSOR - REMOVAL.......8G-7
HEATED SEAT SWITCH - DESCRIPTION....8G-7
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SWITCH - INSTALLATION . . . 8G-9
HEATED SEAT SWITCH - OPERATION......8G-8
HEATED SEAT SWITCH - REMOVAL.......8G-9
HEATED SEAT SYSTEM - DESCRIPTION....8G-3
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-4
HEATED SEAT SYSTEM - OPERATION.....8G-4
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-44
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.......................7-43
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-42
HEATER - DESCRIPTION, FUEL..........14-63
HEATER - DESCRIPTION, INTAKE AIR.....14-91
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-42
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-63
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-43
HEATER - INSTALLATION, INTAKE AIR......14-91
HEATER - OPERATION, ENGINE BLOCK....7-42
HEATER - OPERATION, FUEL............14-63
HEATER - OPERATION, INTAKE AIR......14-91
HEATER - REMOVAL, ENGINE BLOCK......7-43
HEATER - REMOVAL, INTAKE AIR........14-91
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-14
HEATER CORE - DESCRIPTION..........24-50
HEATER CORE - INSTALLATION.........24-50
HEATER CORE - OPERATION............24-50
HEATER CORE - REMOVAL.............24-50
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-5
HEATER RELAY - DESCRIPTION, FUEL....14-64
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-92
HEATER RELAY - INSTALLATION, FUEL . . . 14-64
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-93
HEATER RELAY - OPERATION, FUEL......14-64
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-92
HEATER RELAY - REMOVAL, FUEL.......14-64
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-93
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-27
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-10
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER
...................8L-10
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION
.......................24-35
HIGH PRESSURE RELIEF VALVE -
OPERATION
.........................24-36
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE
..........................22-6
HIGH/LOW RELAY - DESCRIPTION,
WIPER
.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER
.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER
.............................8R-21
HIGH/LOW RELAY - OPERATION, WIPER
. . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER
. . . 8R-21
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-69
HINGE - INSTALLATION.....23-16,23-22,23-31,
23-46
HINGE - INSTALLATION, CENTER SEAT
BACK..............................23-80
HINGE - REMOVAL....23-16,23-22,23-31,23-46
HINGE - REMOVAL, CENTER SEAT BACK . . 23-79
HINGE COVER - INSTALLATION, CENTER
SEAT BACK INERTIA..................23-78
HINGE COVER - REMOVAL, CENTER
SEAT BACK INERTIA..................23-78
HITCH - INSTALLATION, TRAILER........13-25
HITCH - REMOVAL, TRAILER...........13-25
HOAT COOLANT - DESCRIPTION..........7-37
HOISTING - STANDARD PROCEDURE......0-14
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - OPERATION, BATTERY.....8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-52
HOLDER - REMOVAL, CUP.............23-52
HOLDING CLUTCHES - DESCRIPTION....21-546
HOLDING CLUTCHES - OPERATION.....21-546
HOLE PLUG - INSTALLATION, CAMSHAFT
CORE..............................9-201
HOLE PLUG - REMOVAL, CAMSHAFT
CORE..............................9-200
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE.......9-126,9-233,9-360,9-37
HOOD - INSTALLATION................23-47
HOOD - REMOVAL....................23-47
HOOK - INSTALLATION, COAT...........23-67
HOOK - REMOVAL, COAT..............23-67
HOOK ASSEMBLY - INSTALLATION,
FRONT TOW........................13-26
HOOK ASSEMBLY - REMOVAL, FRONT
TOW ..............................13-26
HORN - DIAGNOSIS AND TESTING.......8H-1
HORN - INSTALLATION.................8H-2
HORN - REMOVAL....................8H-2
HORN SWITCH - DESCRIPTION..........8H-2
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-2
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - GEAR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - GEAR TO COOLER - REMOVAL,
RETURN............................19-43
HOSE - INSTALLATION, FRONT BRAKE......5-9
HOSE - INSTALLATION, PRESSURE . 19-43,19-44
HOSE - INSTALLATION, REAR BRAKE.......5-9
HOSE - REMOVAL, FRONT...............5-9
HOSE - REMOVAL, PRESSURE.....19-43,19-44
HOSE - REMOVAL, REAR BRAKE..........5-8
HOSE - RESERVOIR TO COOLER -
INSTALLATION, RETURN..........19-43,19-44
HOSE - RESERVOIR TO COOLER -
REMOVAL, RETURN.............19-43,19-44
HOSE ASSEMBLY - INSTALLATION, REAR
TUBE................................5-9
HOSE ASSEMBLY - REMOVAL, REAR
TUBE................................5-8
HOSE CLAMPS - DESCRIPTION...........7-3
HOSE CLAMPS - OPERATION.............7-5
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-68
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-70
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-69
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT..............24-33
HOSES/TUBES - DESCRIPTION, WASHER . 8R-11
HOSES/TUBES - OPERATION, WASHER . . . 8R-11
HOUSING - ASSEMBLY, HVAC
...........24-28
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH
..............................6-8
HOUSING - DISASSEMBLY, HVAC
........24-28
HOUSING - INSTALLATION, CLUTCH
......6-10
HOUSING - INSTALLATION, GEAR
........9-349HOUSING - INSTALLATION, HVAC........24-29
HOUSING - INSTALLATION, ROCKER.....9-304
HOUSING - REMOVAL, CLUTCH..........6-10
HOUSING - REMOVAL, GEAR...........9-348
HOUSING - REMOVAL, HVAC...........24-27
HOUSING - REMOVAL, ROCKER.........9-304
HOUSING BUSHING - INSTALLATION,
EXTENSION........................21-200
HOUSING BUSHING - REMOVAL,
EXTENSION........................21-200
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-616,21-682
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-616,21-682
HOUSING COVER - INSTALLATION, GEAR . 9-350
HOUSING COVER - REMOVAL, GEAR.....9-349
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER . . . 21-143,21-324,21-495
HOUSING SEAL - INSTALLATION,
ADAPTER...............21-127,21-539,21-83
HOUSING SEAL - INSTALLATION,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL - REMOVAL, ADAPTER . . 21-127,
21-539,21-83
HOUSING SEAL - REMOVAL,
EXTENSION.......21-127,21-200,21-380,21-83
HOUSING SEAL AND DUST BOOT -
INSTALLATION, EXTENSION.....21-652,21-716
HOUSING SEAL AND DUST BOOT -
REMOVAL, EXTENSION.........21-652,21-716
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
H-SECTION REPLACEMENT - STANDARD
PROCEDURE, REAR FRAME............13-15
HUB / BEARING - INSTALLATION.........2-31
HUB / BEARING - REMOVAL.............2-30
HVAC HOUSING - ASSEMBLY...........24-28
HVAC HOUSING - DISASSEMBLY........24-28
HVAC HOUSING - INSTALLATION........24-29
HVAC HOUSING - REMOVAL............24-27
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-25
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING.........9-124,9-31
HYDRAULIC LIFTERS - CLEANING . . 9-260,9-388
HYDRAULIC LIFTERS - INSTALLATION . . . 9-260,
9-388
HYDRAULIC LIFTERS - REMOVAL . . . 9-259,9-387
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING......21-140,21-321,
21-493
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS........21-175,21-355,21-513
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING......................9-258,9-386
HYDROBOOST - INSTALLATION..........5-22
HYDROBOOST - INSTALLATION, ALL
EXCEPT.............................5-22
HYDROBOOST - REMOVAL..............5-21
HYDROBOOST - REMOVAL, ALL EXCEPT . . . 5-21
HYDRO-BOOST BRAKE BOOSTER -
INSTALLATION........................5-27
HYDRO-BOOST BRAKE BOOSTER -
REMOVAL...........................5-27
HYDROFORM FENDER RAIL REPAIR -
STANDARD PROCEDURE...............13-12
HYDROSTATIC LOCK - STANDARD
PROCEDURE.........9-186,9-232,9-290,9-361
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-2
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-33
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-35
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-33
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-34
IDLER SHAFT - INSTALLATION......9-175,9-80
IDLER SHAFT - REMOVAL
..........9-175,9-79
IGNITION - SPECIFICATIONS, TORQUE
.....8I-3
IGNITION CIRCUIT SENSE -
DESCRIPTION
.......................8E-10
IGNITION CIRCUIT SENSE - OPERATION
. . 8E-12
IGNITION COIL - DESCRIPTION
..........8I-19IGNITION COIL - INSTALLATION.........8I-24
IGNITION COIL - OPERATION............8I-20
IGNITION COIL - REMOVAL.............8I-23
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-33
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-33
IGNITION COIL CAPACITOR - OPERATION . . 8I-33
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-33
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-6
IGNITION COIL RESISTANCE, 4.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.7L V-8.....8I-6
IGNITION COIL RESISTANCE, 5.9L.........8I-6
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-6
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION SWITCH - DESCRIPTION........19-9
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-11
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-9
IGNITION SWITCH - INSTALLATION......19-11
IGNITION SWITCH - OPERATION.........19-9
IGNITION SWITCH - REMOVAL..........19-10
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING . . . 19-11
IGNITION TIMING, SPECIFICATIONS.......8I-6
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE..........................8F-11
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-15
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-13
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-15
IMMOBILIZER SYSTEM INDICATOR
LAMP - DESCRIPTION, SENTRY KEY......8Q-5
IMMOBILIZER SYSTEM INDICATOR
LAMP - OPERATION, SENTRY KEY........8Q-5
IMMOBILIZER SYSTEM INITIALIZATION,
STANDARD PROCEDURE - SENTRY
KEY................................8Q-3
IMMOBILIZER SYSTEM (SKIS),
DESCRIPTION - SENTRY KEY............8Q-1
IMMOBILIZER SYSTEM TRANSPONDER
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY.............8Q-4
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE..................8O-53
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE....................8O-54
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF.....21-201,21-381,
21-541
INDEPENDENT FRONT SUSPENSION -
DESCRIPTION, GEAR..................19-16
INDEPENDENT FRONT SUSPENSION -
INSTALLATION, GEAR.................19-17
INDEPENDENT FRONT SUSPENSION -
REMOVAL, GEAR.....................19-16
INDICATOR - DESCRIPTION, ABS........8J-17
INDICATOR - DESCRIPTION, AIRBAG.....8J-18
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-18
INDICATOR - DESCRIPTION, CARGO
LAMP..............................8J-20
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-21
INDICATOR - DESCRIPTION, CRUISE.....8J-22
INDICATOR - DESCRIPTION, DOOR AJAR . . 8J-23
INDICATOR - DESCRIPTION, ETC........8J-24
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-26
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-27
INDICATOR - DESCRIPTION, LAMP OUT . . . 8J-28
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-29
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-33
INDICATOR - DESCRIPTION, SEATBELT
. . . 8J-34
INDICATOR - DESCRIPTION, SECURITY
. . . 8J-34
INDICATOR - DESCRIPTION, SERVICE
4WD
...............................8J-35
INDICATOR - DESCRIPTION, TRANS
TEMP
..............................8J-38
INDICATOR - DESCRIPTION, TURN
SIGNAL
............................8J-39
DRINDEX 17
Description Group-Page Description Group-Page Description Group-Page

TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS.....................22-10
TIRE ROTATION - STANDARD
PROCEDURE.........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-5
TIRES - DESCRIPTION, RADIAL - PLY.....22-6
TIRES - DESCRIPTION, REPLACEMENT....22-6
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING............................22-8
TO COOLER - INSTALLATION, RETURN
HOSE - GEAR..................19-43,19-44
TO COOLER - INSTALLATION, RETURN
HOSE - RESERVOIR.............19-43,19-44
TO COOLER - REMOVAL, RETURN HOSE
- GEAR............................19-43
TO COOLER - REMOVAL, RETURN HOSE
- RESERVOIR..................19-43,19-44
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO OIL COOLER - INSTALLATION, AIR.....7-75
TO OIL COOLER - REMOVAL, AIR.........7-74
TO OIL COOLER - REMOVAL, WATER......7-74
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-4
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER..........2-4
TOOL - ADJUSTMENT, WITH ADJUSTING . . . 5-36
TOOLS - 4.7L ENGINE, SPECIAL.........9-102
TOOLS - 5.7L ENGINE, SPECIAL.........9-192
TOOLS - 5.9L DIESEL ENGINE, SPECIAL . . 9-294
TOOLS - 5.9L ENGINE, SPECIAL.........9-240
TOOLS - 8.0L ENGINE, SPECIAL.........9-367
TOOLS - 9 1/4 AA, SPECIAL.............2-29
TOOLS - BASE BRAKES, SPECIAL.........5-5
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-7
TOOLS - BODY, SPECIAL...............23-14
TOOLS - COOLING, SPECIAL.............7-20
TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-60
TOOLS - FRONT SUSPENSION, SPECIAL . . . 2-11
TOOLS - FUEL SYSTEM, SPECIAL........14-5
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-6
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-22
TOOLS - RE TRANSMISSION, SPECIAL . . 21-189,
21-370
TOOLS - RFE TRANSMISSION, SPECIAL . . 21-535
TOOLS - STEERING LINKAGE, SPECIAL . . . 19-35
TOOLS - STEERING, SPECIAL............19-5
TOOLS - TRANSFER CASE NV271/NV273,
SPECIAL....................21-650,21-714
TOOLS - WHEEL ALIGNMENT, SPECIAL.....2-7
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, DIAGNOSIS AND TESTING -
SPECIAL............................11-4
TOOLS, FRONT AXLE - 9 1/4 AA -
SPECIAL............................3-53
TOOLS, FRONT AXLE - C205F - SPECIAL . . . 3-30
TOOLS, HALF SHAFT - SPECIAL..........3-12
TOOLS, HEADLAMP ALIGNMENT -
SPECIAL............................8L-7
TOOLS, MANUAL TRANSMISSION -
NV3500 - SPECIAL...................21-40
TOOLS, MANUAL TRANSMISSION -
NV4500 - SPECIAL...................21-79
TOOLS, MANUAL TRANSMISSION -
NV5600 - SPECIAL..................21-122
TOOLS, PROPELLER SHAFT - SPECIAL.....3-6
TOOLS, REAR AXLE - 10 1/2 AA -
SPECIAL...........................3-108
TOOLS, REAR AXLE - 11 1/2 AA -
SPECIAL
...........................3-135
TOOLS, REAR AXLE - 9 1/4 - SPECIAL
.....3-80
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL
.....................8F-7
TOOLS, SPECIFICATIONS - SPECIAL
.......9-16
TOP COVER - INSTALLATION,
INSTRUMENT PANEL
..................23-60TOP COVER - REMOVAL, INSTRUMENT
PANEL.............................23-59
TORSION BAR - DESCRIPTION...........2-25
TORSION BAR - INSTALLATION..........2-26
TORSION BAR - OPERATION.............2-25
TORSION BAR - REMOVAL..............2-25
TORSION BAR CROSS MEMBER
BUSHING - INSTALLATION..............2-14
TORSION BAR CROSSMEMBER
BUSHING - REMOVAL..................2-12
TOUCH-UP - DESCRIPTION, PAINT.......23-75
TOUCH-UP - STANDARD PROCEDURE,
PAINT.............................23-75
TOW HOOK ASSEMBLY - INSTALLATION,
FRONT.............................13-26
TOW HOOK ASSEMBLY - REMOVAL,
FRONT.............................13-26
TOW WIRING - DESCRIPTION, TRAILER . . 8L-22
TOWING - STANDARD PROCEDURE.......0-15
TRACK - DESCRIPTION, POWER SEAT....8N-18
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-18
TRACK - INSTALLATION, POWER SEAT . . . 8N-19
TRACK - INSTALLATION, SEAT..........23-83
TRACK - OPERATION, POWER SEAT.....8N-18
TRACK - REMOVAL, POWER SEAT.......8N-19
TRACK - REMOVAL, SEAT..............23-83
TRACK BAR - INSTALLATION...........19-37
TRACK BAR - REMOVAL................19-37
TRAC-RITE - ASSEMBLY, DIFFERENTIAL . . 3-120,
3-147
TRAC-RITE - CLEANING, DIFFERENTIAL . . 3-119,
3-146
TRAC-RITE - DESCRIPTION,
DIFFERENTIAL..................3-118,3-145
TRAC-RITE - DISASSEMBLY,
DIFFERENTIAL..................3-118,3-145
TRAC-RITE - INSPECTION, DIFFERENTIAL . 3-119,
3-146
TRAC-RITE - OPERATION, DIFFERENTIAL . 3-118,
3-145
TRAILER HITCH - INSTALLATION........13-25
TRAILER HITCH - REMOVAL............13-25
TRAILER TOW WIRING - DESCRIPTION . . . 8L-22
TRANS COOLER - 5.9L DIESEL -
DESCRIPTION........................7-73
TRANS COOLER - 5.9L DIESEL -
OPERATION..........................7-74
TRANS TEMP INDICATOR -
DESCRIPTION.......................8J-38
TRANS TEMP INDICATOR - OPERATION . . . 8J-38
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-15
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-15
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-16
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-15
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-16
TRANSFER CASE - NV241 GENII -
ASSEMBLY.........................21-604
TRANSFER CASE - NV241 GENII -
CLEANING
.........................21-602
TRANSFER CASE - NV241 GENII -
DESCRIPTION
.........................0-4
TRANSFER CASE - NV241 GENII -
DESCRIPTION
......................21-591
TRANSFER CASE - NV241 GENII -
DIAGNOSIS AND TESTING
............21-592
TRANSFER CASE - NV241 GENII -
DISASSEMBLY
......................21-593
TRANSFER CASE - NV241 GENII -
INSPECTION
.......................21-602
TRANSFER CASE - NV241 GENII -
INSTALLATION
......................21-614
TRANSFER CASE - NV241 GENII -
OPERATION
........................21-591
TRANSFER CASE - NV241 GENII -
REMOVAL
.........................21-593
TRANSFER CASE - NV243 - ASSEMBLY
. . 21-670
TRANSFER CASE - NV243 - CLEANING
. . 21-668
TRANSFER CASE - NV243 -
DESCRIPTION
.........................0-4
TRANSFER CASE - NV243 -
DESCRIPTION
......................21-658TRANSFER CASE - NV243 - DIAGNOSIS
AND TESTING......................21-659
TRANSFER CASE - NV243 -
DISASSEMBLY......................21-660
TRANSFER CASE - NV243 - INSPECTION . 21-668
TRANSFER CASE - NV243 -
INSTALLATION......................21-679
TRANSFER CASE - NV243 - OPERATION . 21-659
TRANSFER CASE - NV243 - REMOVAL . . . 21-660
TRANSFER CASE - NV271 - ASSEMBLY . . 21-637
TRANSFER CASE - NV271 - CLEANING . . 21-635
TRANSFER CASE - NV271 -
DESCRIPTION.........................0-4
TRANSFER CASE - NV271 -
DESCRIPTION......................21-623
TRANSFER CASE - NV271 - DIAGNOSIS
AND TESTING......................21-624
TRANSFER CASE - NV271 -
DISASSEMBLY......................21-625
TRANSFER CASE - NV271 - INSPECTION . 21-635
TRANSFER CASE - NV271 -
INSTALLATION......................21-649
TRANSFER CASE - NV271 - OPERATION . 21-623
TRANSFER CASE - NV271 - REMOVAL . . . 21-625
TRANSFER CASE - NV273 - ASSEMBLY . . 21-701
TRANSFER CASE - NV273 - CLEANING . . 21-698
TRANSFER CASE - NV273 -
DESCRIPTION.........................0-4
TRANSFER CASE - NV273 -
DESCRIPTION......................21-687
TRANSFER CASE - NV273 - DIAGNOSIS
AND TESTING......................21-688
TRANSFER CASE - NV273 -
DISASSEMBLY......................21-689
TRANSFER CASE - NV273 - INSPECTION . 21-699
TRANSFER CASE - NV273 -
INSTALLATION......................21-713
TRANSFER CASE - NV273 - OPERATION . 21-688
TRANSFER CASE - NV273 - REMOVAL . . . 21-689
TRANSFER CASE CONTROL MODULE -
DESCRIPTION.......................8E-15
TRANSFER CASE CONTROL MODULE -
OPERATION.........................8E-15
TRANSFER CASE, NV241 GENII........21-614
TRANSFER CASE, NV241/NV243 . . 21-615,21-680
TRANSFER CASE, NV243.............21-680
TRANSFER CASE, NV271.............21-649
TRANSFER CASE NV271/NV273, SPECIAL
TOOLS......................21-650,21-714
TRANSFER CASE, NV273.............21-713
TRANSFER CASE SKID PLATE -
INSTALLATION.......................13-26
TRANSFER CASE SKID PLATE -
REMOVAL..........................13-26
TRANSFER PUMP - DESCRIPTION, FUEL . . 14-75
TRANSFER PUMP - INSTALLATION, FUEL . 14-76
TRANSFER PUMP - OPERATION, FUEL....14-76
TRANSFER PUMP - REMOVAL, FUEL.....14-76
TRANSMISSION - 45RFE/545RFE -
DESCRIPTION, AUTOMATIC............21-489
TRANSMISSION - 45RFE/545RFE -
OPERATION, AUTOMATIC.............21-490
TRANSMISSION - 46RE - DESCRIPTION,
AUTOMATIC
........................21-131
TRANSMISSION - 46RE - OPERATION,
AUTOMATIC
........................21-133
TRANSMISSION - 48RE - DESCRIPTION,
AUTOMATIC
........................21-312
TRANSMISSION - 48RE - OPERATION,
AUTOMATIC
........................21-314
TRANSMISSION - CLEANING
..........21-104
TRANSMISSION - DESCRIPTION,
MANUAL
.............................0-4
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC
....21-139,21-320,21-491
TRANSMISSION - NV3500 - ASSEMBLY,
MANUAL
...........................21-17
TRANSMISSION - NV3500 - CLEANING,
MANUAL
...........................21-15
TRANSMISSION - NV3500 -
DESCRIPTION, MANUAL
................21-1
TRANSMISSION - NV3500 - DIAGNOSIS
AND TESTING, MANUAL
................21-3
TRANSMISSION - NV3500 -
DISASSEMBLY, MANUAL
................21-4
TRANSMISSION - NV3500 -
INSPECTION, MANUAL
................21-15
DRINDEX 35
Description Group-Page Description Group-Page Description Group-Page

UPPER RADIATOR CROSSMEMBER -
INSTALLATION.......................23-42
UPPER RADIATOR CROSSMEMBER -
REMOVAL..........................23-42
UPPER STEERING COUPLING -
INSTALLATION.......................19-14
UPPER STEERING COUPLING -
REMOVAL..........................19-13
UPPER TRIM - INSTALLATION, B-PILLAR . . 23-65
UPPER TRIM - INSTALLATION, C-PILLAR . . 23-68
UPPER TRIM - REMOVAL, B-PILLAR.....23-65
UPPER TRIM - REMOVAL, C-PILLAR.....23-68
UPSHIFT INDICATOR - DESCRIPTION.....8J-40
UPSHIFT INDICATOR - OPERATION.......8J-40
USAGE - DESCRIPTION, FASTENER.....Intro.-9
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MICRO 420 BATTERY TESTER -
STANDARD PROCEDURE...............8F-12
V-10 - DESCRIPTION, 8.0L.............25-12
V-10 - OPERATION, 8.0L...............25-12
V-10 ENGINE - IGNITION COIL
RESISTANCE, 8.0L.....................8I-6
V-10 ENGINE - SPARK PLUG CABLE
ORDER, 8.0L.........................8I-5
V-10 OR DIESEL ENGINE -
INSTALLATION......................8R-17
V-10 OR DIESEL ENGINE -
INSTALLATION, EXCEPT...............8R-17
V-10 OR DIESEL ENGINE - REMOVAL....8R-16
V-10 OR DIESEL ENGINE - REMOVAL,
EXCEPT............................8R-16
V-6 - ENGINE FIRING ORDER, 3.7L........8I-4
V-6 - IGNITION COIL RESISTANCE, 3.7L....8I-6
V-6/ 4.7L V-8 - DIAGNOSIS AND
TESTING, PCV VALVE - 3.7L............25-19
V-8 - DIAGNOSIS AND TESTING,
DISTRIBUTOR CAP - 5.9L..............8I-18
V-8 - DIAGNOSIS AND TESTING,
DISTRIBUTOR ROTOR - 5.9L............8I-19
V-8 - DIAGNOSIS AND TESTING, PCV
VALVE - 3.7L V-6/ 4.7L................25-19
V-8 - DIAGNOSIS AND TESTING, PCV
VALVE - 5.9L........................25-19
V-8 - ENGINE FIRING ORDER, 4.7L........8I-4
V-8 - ENGINE FIRING ORDER, 5.9L........8I-4
V-8 - IGNITION COIL RESISTANCE, 4.7L....8I-6
V-8 - IGNITION COIL RESISTANCE, 5.7L....8I-6
V-8 ENGINE - FIRING ORDER / CABLE
ROUTING, 5.7L........................8I-4
VAC LEAK DETECTION ASSY -
DESCRIPTION, NATURAL..............25-23
VAC LEAK DETECTION ASSY -
INSTALLATION, NATURAL..............25-24
VAC LEAK DETECTION ASSY -
OPERATION, NATURAL................25-23
VAC LEAK DETECTION ASSY -
REMOVAL, NATURAL..................25-24
VACUUM LINES - DESCRIPTION.........25-22
VACUUM RESERVOIR - DESCRIPTION.....8P-9
VACUUM RESERVOIR - DIAGNOSIS AND
TESTING............................8P-9
VACUUM RESERVOIR - INSTALLATION . . . 8P-10
VACUUM RESERVOIR - OPERATION.......8P-9
VACUUM RESERVOIR - REMOVAL.......8P-10
VACUUM SUPPLY TEST - DIAGNOSIS
AND TESTING........................8P-2
VALVE - 3.7L V-6/ 4.7L V-8 - DIAGNOSIS
AND TESTING, PCV...................25-19
VALVE - 5.9L V-8 - DIAGNOSIS AND
TESTING, PCV.......................25-19
VALVE - CLEANING, OIL PRESSURE
RELIEF.............................9-343
VALVE - DESCRIPTION, CASCADE
OVERFLOW.........................14-77
VALVE - DESCRIPTION, CHECK..........8R-8
VALVE - DESCRIPTION, FUEL PRESSURE
LIMITING...........................14-72
VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-35
VALVE - DESCRIPTION, PCV
............25-16
VALVE - DESCRIPTION, RWAL
...........5-44
VALVE - DESCRIPTION, SOLENOID
SWITCH
...........................21-574
VALVE - DESCRIPTION, TORQUE
CONVERTER DRAINBACK
.......21-262,21-440
VALVE - INSPECTION, OIL PRESSURE
RELIEF
.............................9-343VALVE - INSTALLATION, CHECK..........8R-9
VALVE - INSTALLATION, FUEL
PRESSURE LIMITING.................14-73
VALVE - INSTALLATION, OIL PRESSURE
RELIEF.............................9-343
VALVE - INSTALLATION, RWAL...........5-45
VALVE - OPERATION, CASCADE
OVERFLOW.........................14-77
VALVE - OPERATION, CHECK............8R-8
VALVE - OPERATION, FUEL PRESSURE
LIMITING...........................14-72
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-36
VALVE - OPERATION, PCV..............25-17
VALVE - OPERATION, RWAL.............5-44
VALVE - OPERATION, SOLENOID SWITCH . 21-574
VALVE - OPERATION, TORQUE
CONVERTER DRAINBACK.......21-262,21-440
VALVE - REMOVAL, CHECK..............8R-8
VALVE - REMOVAL, FUEL PRESSURE
LIMITING...........................14-72
VALVE - REMOVAL, OIL PRESSURE
RELIEF.............................9-343
VALVE - REMOVAL, RWAL..............5-45
VALVE - STANDARD PROCEDURE,
TORQUE CONVERTER DRAINBACK.....21-262,
21-440
VALVE BODY - ADJUSTMENTS . . . 21-308,21-487
VALVE BODY - ASSEMBLY......21-299,21-477,
21-590
VALVE BODY - CLEANING . . 21-298,21-476,21-588
VALVE BODY - DESCRIPTION....21-267,21-445,
21-584
VALVE BODY - DISASSEMBLY . . . 21-287,21-465,
21-586
VALVE BODY - INSPECTION.....21-298,21-476,
21-588
VALVE BODY - INSTALLATION . . . 21-307,21-486,
21-590
VALVE BODY - OPERATION.....21-272,21-450,
21-585
VALVE BODY - REMOVAL . 21-286,21-464,21-585
VALVE CABLE - ADJUSTMENTS,
THROTTLE...................21-255,21-432
VALVE CABLE - DESCRIPTION,
THROTTLE...................21-254,21-432
VALVE GUIDE SEALS - DESCRIPTION . . 9-31,9-36
VALVE GUIDES - DESCRIPTION....9-106,9-197
VALVE LASH ADJUSTMENT AND
VERIFICATION - STANDARD
PROCEDURE........................9-308
VALVE SERVICE, STANDARD
PROCEDURE........................9-375
VALVE SPRINGS - DESCRIPTION....9-125,9-31,
9-36
VALVE SPRINGS - INSTALLATION . . 9-126,9-199,
9-31,9-37
VALVE SPRINGS - INSTALLATION,
VALVES ............................9-379
VALVE SPRINGS - REMOVAL . . 9-125,9-199,9-31,
9-37
VALVE SPRINGS - REMOVAL, VALVES....9-377
VALVE SPRINGS AND SEALS - REMOVAL . 9-308
VALVE STEM SEAL - INSTALLATION......9-378
VALVE STEM SEALS - DESCRIPTION.....9-126,
9-198
VALVE STEM SEALS - REMOVAL........9-377
VALVE TIMING - DESCRIPTION...........9-75
VALVE TIMING - OPERATION............9-75
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST....................9-248
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST . 9-122,9-246,9-27,9-305,9-375
VALVES & SEATS - INSPECTION,
INTAKE/EXHAUST....................9-248
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST...........9-123,9-248,9-29
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST...........9-122,9-248,9-28
VALVES AND VALVE SPRINGS -
INSTALLATION.......................9-379
VALVES AND VALVE SPRINGS -
REMOVAL
..........................9-377
VALVES, GUIDES AND SPRINGS -
STANDARD PROCEDURE
..........9-246,9-305
VAPOR CANISTER - DESCRIPTION
.......25-22
VAPOR CANISTER - INSTALLATION
......25-23
VAPOR CANISTER - OPERATION
.........25-22VAPOR CANISTER - REMOVAL..........25-22
VARIABLE BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC.............5-43
VARIABLE BRAKE PROPORTIONING -
OPERATION, ELECTRONIC...............5-43
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS...............8M-4
VEHICLE EMISSION CONTROL
INFORMATION (VECI) - DESCRIPTION . . . Intro.-3
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION......................Intro.-2
VEHICLE INFO CENTER - DESCRIPTION,
ELECTRONIC........................8M-7
VEHICLE INFO CENTER - INSTALLATION,
ELECTRONIC.......................8M-10
VEHICLE INFO CENTER - OPERATION,
ELECTRONIC........................8M-8
VEHICLE INFO CENTER - REMOVAL,
ELECTRONIC.......................8M-10
VEHICLE INFORMATION CENTER -
DIAGNOSIS AND TESTING,
ELECTRONIC........................8M-8
VEHICLE INFORMATION CENTER
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC.............8M-8
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION.....................Intro.-1
VEHICLE THEFT SECURITY SYSTEM,
DIAGNOSIS AND TESTING..............8Q-3
VENT - INSTALLATION, BODY...........23-72
VENT - REMOVAL, BODY..............23-72
VENT GLASS - INSTALLATION, BACKLITE . 23-87
VENT GLASS - REMOVAL, BACKLITE.......23-87
VERIFICATION - SERVICE PROCEDURE,
TIMING.............................9-76
VERIFICATION - STANDARD
PROCEDURE, ENGINE TIMING..........9-165
VERIFICATION - STANDARD
PROCEDURE, TIMING.................9-348
VERIFICATION - STANDARD
PROCEDURE, VALVE LASH
ADJUSTMENT.......................9-308
VERIFICATION TEST - STANDARD
PROCEDURE.........................8O-8
VIBRATION - DIAGNOSIS AND TESTING,
TIRE NOISE OR.......................22-7
VIBRATION DAMPER - INSPECTION......9-335
VIBRATION DAMPER - INSTALLATION....9-142,
9-209,9-263,9-335,9-392,9-55
VIBRATION DAMPER - REMOVAL . . 9-141,9-209,
9-263,9-335,9-392,9-54
VIEW MIRROR - INSTALLATION, SIDE....23-41
VIEW MIRROR - REMOVAL, REAR.......23-71
VIEW MIRROR - REMOVAL, SIDE........23-41
VIEW MIRROR FLAG - INSTALLATION,
SIDE..............................23-27
VIEW MIRROR FLAG - REMOVAL, SIDE . . . 23-27
VIEW MIRROR GLASS - INSTALLATION,
SIDE..............................23-44
VIEW MIRROR GLASS - REMOVAL, SIDE . . 23-42
VISCOUS CLUTCH - 5.9L DIESEL -
DESCRIPTION, FAN DRIVE..............7-55
VISCOUS CLUTCH - 5.9L DIESEL -
OPERATION, FAN DRIVE................7-55
VISCOUS CLUTCH - DESCRIPTION, FAN
DRIVE..............................7-54
VISCOUS CLUTCH - OPERATION, FAN
DRIVE..............................7-54
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING............................7-54
VISCOUS FAN DRIVE - DIAGNOSIS AND
TESTING, ELECTRONICLY CONTOLLED.....7-56
VISOR - INSTALLATION, SUN...........23-71
VISOR - REMOVAL, SUN...............23-71
VISOR SUPPORT - INSTALLATION, SUN . . . 23-72
VISOR SUPPORT - REMOVAL, SUN......23-72
VOLT SUPPLIES - DESCRIPTION, 5......8E-10
VOLT SUPPLIES - OPERATION, 5........8E-11
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE GAUGE - DESCRIPTION........8J-40
VOLTAGE GAUGE - OPERATION
..........8J-41
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF
...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION
....8F-27
VOLTAGE REGULATOR - OPERATION
.....8F-27
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT
...........8F-10
DRINDEX 37
Description Group-Page Description Group-Page Description Group-Page

VOLUME CHECK - STANDARD
PROCEDURE, OIL PUMP..............21-563
WAIT-TO-START INDICATOR -
DESCRIPTION.......................8J-42
WAIT-TO-START INDICATOR -
OPERATION.........................8J-42
WARNING - INSTALLATION.............23-88
WARNING - REMOVAL................23-88
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - SERVICE WARNINGS........24-32
WARNING - WINDSHIELD SAFETY
PRECAUTIONS.......................23-88
WARNING, CLUTCH.....................6-2
WARNINGS, GENERAL..............8W-01-7
WARNINGS, RESTRAINT SYSTEM........8O-5
WARNINGS, WARNING - SAFETY
PRECAUTIONS........................23-1
WARNINGS, WARNING - SERVICE.......24-32
WASHER FLUID INDICATOR -
DESCRIPTION.......................8J-42
WASHER FLUID INDICATOR -
OPERATION.........................8J-42
WASHER FLUID LEVEL SWITCH -
DESCRIPTION........................8R-9
WASHER FLUID LEVEL SWITCH -
INSTALLATION......................8R-11
WASHER FLUID LEVEL SWITCH -
OPERATION..........................8R-9
WASHER FLUID LEVEL SWITCH -
REMOVAL..........................8R-10
WASHER HOSES/TUBES - DESCRIPTION . . 8R-11
WASHER HOSES/TUBES - OPERATION....8R-11
WASHER NOZZLE - DESCRIPTION.......8R-12
WASHER NOZZLE - INSTALLATION......8R-12
WASHER NOZZLE - OPERATION.........8R-12
WASHER NOZZLE - REMOVAL..........8R-12
WASHER PUMP/MOTOR - DESCRIPTION . . 8R-13
WASHER PUMP/MOTOR - INSTALLATION . 8R-14
WASHER PUMP/MOTOR - OPERATION . . . 8R-13
WASHER PUMP/MOTOR - REMOVAL.....8R-14
WASHER RESERVOIR - DESCRIPTION....8R-15
WASHER RESERVOIR - OPERATION......8R-15
WASHER SYSTEM - CLEANING, WIPER....8R-6
WASHER SYSTEM - DIAGNOSIS AND
TESTING, WIPER.....................8R-6
WASHER SYSTEM - INSPECTION, WIPER . . 8R-7
WATER DRAINING AT FUEL FILTER -
STANDARD PROCEDURES..............14-57
WATER IN FUEL SENSOR -
DESCRIPTION.......................14-77
WATER IN FUEL SENSOR - OPERATION . . . 14-78
WATER IN FUEL SENSOR - REMOVAL....14-78
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-1
WATER PUMP - 5.7L - INSTALLATION.....7-71
WATER PUMP - 5.7L - REMOVAL.........7-70
WATER PUMP - 5.9L - CLEANING........7-64
WATER PUMP - 5.9L - DESCRIPTION......7-62
WATER PUMP - 5.9L - INSPECTION.......7-64
WATER PUMP - 5.9L - INSTALLATION.....7-64
WATER PUMP - 5.9L - OPERATION.......7-62
WATER PUMP - 5.9L - REMOVAL.........7-63
WATER PUMP - 5.9L DIESEL -
CLEANING...........................7-67
WATER PUMP - 5.9L DIESEL -
DESCRIPTION........................7-67
WATER PUMP - 5.9L DIESEL -
INSPECTION.........................7-68
WATER PUMP - 5.9L DIESEL -
INSTALLATION........................7-68
WATER PUMP - 5.9L DIESEL -
OPERATION
..........................7-67
WATER PUMP - 5.9L DIESEL - REMOVAL
. . 7-67
WATER PUMP - DESCRIPTION
...........7-64
WATER PUMP - DIAGNOSIS AND
TESTING
........................7-62,7-67
WATER PUMP - OPERATION
.............7-64
WATER PUMP BYPASS - DESCRIPTION
....7-64
WATER PUMP BYPASS - OPERATION
......7-65
WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION
..........7-70WATER PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL.............7-68
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - INSTALLATION......7-70
WATER PUMP BYPASS HOSE WITHOUT
AIR CONDITIONING - REMOVAL..........7-69
WATER SEPARATOR - DESCRIPTION,
FUEL FILTER........................14-61
WATER SEPARATOR - INSTALLATION,
FUEL FILTER........................14-62
WATER SEPARATOR - OPERATION, FUEL
FILTER.............................14-61
WATER SEPARATOR - REMOVAL, FUEL
FILTER.............................14-61
WATER TO OIL COOLER - REMOVAL......7-74
WATERDAM - INSTALLATION......23-25,23-34
WATERDAM - REMOVAL..........23-25,23-34
WATER-IN-FUEL INDICATOR -
DESCRIPTION.......................8J-43
WATER-IN-FUEL INDICATOR -
OPERATION.........................8J-43
WEAR - STANDARD PROCEDURE,
MEASURING TIMING CHAIN............9-165
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD......................22-7
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE.......................22-8
WEAR, STANDARD PROCEDURE -
MEASURING TIMING CHAIN.............9-76
WEATHERSTRIP - INSTALLATION, DRIP
RAIL..............................23-91
WEATHERSTRIP - INSTALLATION, FRONT
DOOR GLASS RUN.....................23-92
WEATHERSTRIP - INSTALLATION, REAR
DOOR GLASS RUN...................23-93
WEATHERSTRIP - REMOVAL, DRIP RAIL . . 23-91
WEATHERSTRIP - REMOVAL, FRONT
DOOR GLASS RUN...................23-92
WEATHERSTRIP - REMOVAL, REAR
DOOR GLASS RUN...................23-93
WEATHERSTRIP RETAINER -
INSTALLATION, A-PILLAR..............23-91
WEATHERSTRIP RETAINER -
INSTALLATION, DRIP RAIL.............23-92
WEATHERSTRIP RETAINER - REMOVAL,
A-PILLAR...........................23-91
WEATHERSTRIP RETAINER - REMOVAL,
DRIP RAIL..........................23-92
WELD LOCATIONS - SPECIFICATIONS . . . 23-122
WHEEL - INSTALLATION, STEERING......19-15
WHEEL - REMOVAL, STEERING.........19-15
WHEEL ALIGNMENT - DESCRIPTION.......2-1
WHEEL ALIGNMENT - OPERATION.........2-2
WHEEL ALIGNMENT, SPECIAL TOOLS......2-7
WHEEL ANTILOCK - DIAGNOSIS AND
TESTING, REAR.......................5-42
WHEEL BALANCE - STANDARD
PROCEDURE, TIRE....................22-4
WHEEL COVER - REMOVAL............22-14
WHEEL INSPECTION, DIAGNOSIS AND
TESTING...........................22-11
WHEEL INSTALLATION - STANDARD
PROCEDURE, DUAL REAR.............22-12
WHEEL REPLACEMENT - STANDARD
PROCEDURE........................22-12
WHEEL RUNOUT - DIAGNOSIS AND
TESTING, TIRE.......................22-1
WHEEL SPEED SENSOR - DESCRIPTION,
FRONT..............................5-41
WHEEL SPEED SENSOR - DIAGNOSIS
AND TESTING, REAR...................5-43
WHEEL SPEED SENSOR -
INSTALLATION, FRONT.................5-42
WHEEL SPEED SENSOR -
INSTALLATION, REAR..................5-43
WHEEL SPEED SENSOR - OPERATION,
FRONT..............................5-41
WHEEL SPEED SENSOR - REMOVAL,
FRONT..............................5-41
WHEEL SPEED SENSOR - REMOVAL,
REAR...............................5-42
WHEEL WITH MATCHING TIRE -
DESCRIPTION, FULL SIZE, SPARE.......22-15WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT................23-41
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, REAR.................23-41
WHEELHOUSE SPLASH SHIELD -
REMOVAL, FRONT....................23-40
WHEELHOUSE SPLASH SHIELD -
REMOVAL, REAR.....................23-41
WHEELS - DESCRIPTION..............22-11
WHEELS - OPERATION................22-11
WIND NOISE - DIAGNOSIS AND TESTING . . 23-2
WINDOW MOTOR - REMOVAL..........8N-22
WINDOW REGULATOR - MANUAL -
INSTALLATION..................23-26,23-35
WINDOW REGULATOR - MANUAL -
REMOVAL.....................23-26,23-35
WINDOW REGULATOR - POWER -
INSTALLATION..................23-25,23-34
WINDOW REGULATOR - POWER -
REMOVAL.....................23-25,23-34
WINDOW SWITCH - DIAGNOSIS AND
TESTING...........................8N-22
WINDOW SWITCH - INSTALLATION......8N-23
WINDOW SWITCH - REMOVAL..........8N-23
WINDOWS - DESCRIPTION, POWER.....8N-21
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-21
WINDOWS - OPERATION, POWER.......8N-21
WINDSHIELD SAFETY PRECAUTIONS,
WARNING..........................23-88
WIPER & WASHER SYSTEM - CLEANING....8R-6
WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING..............8R-6
WIPER & WASHER SYSTEM -
INSPECTION.........................8R-7
WIPER ARM - DESCRIPTION...........8R-18
WIPER ARM - INSTALLATION...........8R-19
WIPER ARM - OPERATION.............8R-18
WIPER ARM - REMOVAL..............8R-18
WIPER BLADE - DESCRIPTION..........8R-19
WIPER BLADE - INSTALLATION.........8R-20
WIPER BLADE - OPERATION...........8R-19
WIPER BLADE - REMOVAL.............8R-19
WIPER HIGH/LOW RELAY -
DESCRIPTION.......................8R-20
WIPER HIGH/LOW RELAY - DIAGNOSIS
AND TESTING.......................8R-21
WIPER HIGH/LOW RELAY -
INSTALLATION......................8R-21
WIPER HIGH/LOW RELAY - OPERATION . . 8R-20
WIPER HIGH/LOW RELAY - REMOVAL....8R-21
WIPER MODULE - DESCRIPTION........8R-22
WIPER MODULE - INSTALLATION.......8R-23
WIPER MODULE - OPERATION..........8R-23
WIPER MODULE - REMOVAL...........8R-23
WIPER ON/OFF RELAY - DESCRIPTION . . . 8R-25
WIPER ON/OFF RELAY - DIAGNOSIS AND
TESTING...........................8R-26
WIPER ON/OFF RELAY - INSTALLATION . . . 8R-26
WIPER ON/OFF RELAY - OPERATION.....8R-25
WIPER ON/OFF RELAY - REMOVAL......8R-26
WIPERS/WASHERS - DESCRIPTION.......8R-1
WIPERS/WASHERS - OPERATION........8R-4
WIRE SPLICING - STANDARD
PROCEDURE
.....................8W-01-15
WIRING - DESCRIPTION, TRAILER TOW
. . 8L-22
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE
.....................8W-01-1
WIRING HARNESS - DIAGNOSIS AND
TESTING
.........................8W-01-7
WIRING/TERMINAL, SPECIAL TOOLS
. . 8W-01-10
WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS
HOSE
...............................7-70
WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS
HOSE
...............................7-69
WORN THREADS - STANDARD
PROCEDURE,
REPAIR DAMAGED OR
......9-186,9-232,9-289,
9-361,9-9,9-93
38 INDEXDR
Description Group-Page Description Group-Page Description Group-Page