driver seat adjustment DODGE RAM 2003 Service Repair Manual

(10) Install the steering column opening cover
(Refer to 23 - BODY/INSTRUMENT PANEL/STEER-
ING COLUMN OPENING COVER - INSTALLA-
TION).
(11) Reconnect the negative battery cable.
ADJUSTABLE PEDAL MOTOR
DESCRIPTION
The Adjustable Pedals System (APS) is designed to
enable the fore and aft repositioning of the brake and
accelerator pedals. This results in improved ergonom-
ics in relation to the steering wheel for taller and
shorter drivers. Being able to adjust the pedal posi-
tions also allows the driver to set steering wheel tilt
and seat position to the most comfortable position.
The position of the brake and accelerator pedals can
be adjusted without compromising safety or comfort
in actuating the pedals.
Change of pedal position is accomplished by means
of a motor driven screw. Operating the adjustable
pedal switch activates the pedal drive motor (Fig.
45). The pedal drive motor turns a screw that
changes the position of the brake and accelerator
pedals. The pedal can be moved rearward (closer to
the driver) or forward (away from driver). The brake
pedal is moved on its drive screw to a position where
the driver feels most comfortable.
The accelerator pedal is moved at the same time
and the same distance as the brake pedal.
Neither the pedal drive motor (Fig. 45) nor drive
mechanism are subject to the mechanical stress of
brake or accelerator application.
²SYSTEM FEATURES:
²Range of Adjustment: The pedals may be
adjusted up to 3 in. (75 mm)
²Pedal Adjustment Speed: 0.5 in./sec (12.5
mm/sec)
²Pedal Adjustment Inhibitors: Pedal adjust-
ment is inhibited when the vehicle is in reverse or
when cruise control is activated.
REMOVAL
(1) Disconnect the negative battery cable.
(2) Remove the kneeblocker (Refer to 23 - BODY/
INSTRUMENT PANEL/STEERING COLUMN
OPENING COVER - REMOVAL).
(3) Remove the brake light switch and discard
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
EXTERIOR/BRAKE LAMP SWITCH - REMOVAL).
(4) Disconnect the adjustable pedal cables from the
brake and accelerator pedals.
(5) Disconnect the electrical connector.
(6) Unclip the cable fasteners to the support.(7) Remove the one mounting bolt for the adjust-
able pedal motor (Fig. 46).
(8) Remove the adjustable pedal motor with the
cables.
NOTE: Adjustable pedal cables are not serviceable.
If they need service the adjustable pedal motor with
the cables must be installed.
INSTALLATION
NOTE: Adjustable pedal cables are not serviceable.
If they need service the adjustable pedal motor with
the cables must be installed.
(1) Install the adjustable pedal motor with the
cables.
Fig. 45 ADJUSTABLE PEDAL MOTOR
1 - ADJUSTABLE PEDAL MOTOR
2 - CABLES
3 - ELECTRICAL CONNECTOR
Fig. 46 ADJUSTABLE PEDAL MOTOR
1 - ADJUSTABLE PEDAL MOTOR
2 - MOUNTING BOLT
5 - 24 BRAKES - BASEDR
PEDAL (Continued)

DRIVER SEAT SWITCH
DESCRIPTION
The power seat on this model can be adjusted in
eight different directions, up, down, front up, front
down, rear up, rear down, rearward and forward.
The power seat switch (Fig. 1) on this model has an
additional switch knob for adjusting the power lum-
bar support. The power seat switch is located on the
outboard side of the seat cushion on the seat cushion
side shield. Refer to the owner's manual in the vehi-
cle glove box for more information on the power seat
switch functions and the seat adjusting procedures.
The individual switches in the power seat switch
assembly cannot be repaired. If one switch is dam-
aged or faulty, the entire power seat switch assembly
must be replaced.
OPERATION
When a power switch control knob or knobs are
actuated, a battery feed and a ground path are
applied through the switch contacts to the power seat
track or recliner adjuster motor. The selected
adjuster motor operates to move the seat track or
recliner through its drive unit in the selected direc-
tion until the switch is released, or until the travel
limit of the adjuster is reached. When the switch ismoved in the opposite direction, the battery feed and
ground path to the motor are reversed through the
switch contacts. This causes the adjuster motor to
run in the opposite direction.
No power seat switch should be held applied in any
direction after the adjuster has reached its travel
limit. The power seat adjuster motors each contain a
self-resetting circuit breaker to protect them from
overload. However, consecutive or frequent resetting
of the circuit breaker must not be allowed to con-
tinue, or the motor may be damaged.
DIAGNOSIS AND TESTING - DRIVER SEAT
SWITCH
For circuit descriptions and diagrams, refer to Wir-
ing.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the power seat switch from the power
seat.
(3) Use an ohmmeter to test the continuity of the
power seat switches in each position. See the Power
Seat Switch Continuity chart (Fig. 2). If OK, refer to
Power Seat Track Diagnosis and Testing in this
group. If not OK, replace the faulty power seat
switch.
DRIVER POWER SEAT SWITCH TEST TABLE
DRIVER SWITCH
POSITIONCONTINUITY BETWEEN
OFF B-N, B-J, B-M
B-E, B-L, B-K
VERTICAL UP A-E, A-M, B-N, B-E
VERTICAL DOWN A-J, A-N, B-M, B-E
Fig. 1 DR Power Seat Switch
1 - POWER SEAT SWITCH ASSEMBLY
2 - FRONT SEAT CUSHION ADJUSTMENT BUTTON
3 - COMPLETE SEAT ADJUSTMENT BUTTON
4 - REAR SEAT CUSHION ADJUSTMENT BUTTON
5 - LUMBAR ADJUSTMENT BUTTON
Fig. 2 Testing Driver Power Seat Switch
DRPOWER SEATS 8N - 15

DRIVER POWER SEAT SWITCH TEST TABLE
DRIVER SWITCH
POSITIONCONTINUITY BETWEEN
HORIZONTAL
FORWARDA-L, B-K
HORIZONTAL
REARWARDA-K, B-L
FRONT TILT UP A-M, B-N
FRONT TILT DOWN A-N, B-M
REAR TILT UP A-E, B-J
REAR TILT DOWN A-J, B-E
LUMBAR OFF O-P, O-R, P-R
LUMPAR UP (INFLATE) O-P, Q-R
LUMBAR DOWN
(DEFLATE)O-R, P-Q
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the seat cushion side shield from the
seat. Refer to the Body section of the service manual
for the procedure.
(3) Pull the switch bezel or side shield unit out
from the seat far enough to access the switch wire
harness connector. Gently pry the locking tabs of the
switch away from the wire harness connector and
carefully unplug the connector from the power seat
switch module.
(4) Remove the screws that secure the power seat
switch (Fig. 3).
INSTALLATION
(1) Position the power seat switch on the seat
cushion side shield and install the screws that secure
the power seat switch to seat cushion side shield.
(2) Connect the electrical connector.
(3) Install the seat cushion side shield on the seat.
Refer to the Body section of the service manual for
the procedure.
(4) If equipped, install the screw that secures the
recliner lever to the recliner mechanism release shaft
on the outboard side of the front seat.
(5) Connect the battery negative cable.
PASSENGER SEAT SWITCH
DESCRIPTION
The power seat on this model can be adjusted in
eight different directions, up, down, front up, front
down, rear up, rear down, rearward and forward.
The power seat switch (Fig. 4) on this model has an
additional switch knob for adjusting the power lum-
bar support. The power seat switch is located on the
outboard side of the seat cushion on the seat cushion
side shield. Refer to the owner's manual in the vehi-
cle glove box for more information on the power seat
switch functions and the seat adjusting procedures.
Fig. 3 Power Seat Switch Remove/Install
1 - SEAT SIDE SHIELD
2 - POWER SEAT SWITCH
3 - SCREWS
Fig. 4 DR Power Seat Switch
1 - POWER SEAT SWITCH ASSEMBLY
2 - FRONT SEAT CUSHION ADJUSTMENT BUTTON
3 - COMPLETE SEAT ADJUSTMENT BUTTON
4 - REAR SEAT CUSHION ADJUSTMENT BUTTON
5 - LUMBAR ADJUSTMENT BUTTON
8N - 16 POWER SEATSDR
DRIVER SEAT SWITCH (Continued)

(4) Remove the screws that secure the power seat
switch (Fig. 6).
INSTALLATION
(1) Position the power seat switch on the seat
cushion side shield and install the screws that secure
the power seat switch to seat cushion side shield.
(2) Connect the electrical connector.
(3) Install the seat cushion side shield on the seat.
Refer to the Body section of the service manual for
the procedure.
(4) If equipped, install the screw that secures the
recliner lever to the recliner mechanism release shaft
on the outboard side of the front seat.
(5) Connect the battery negative cable.
POWER SEAT TRACK
DESCRIPTION
The eight-way power seat option includes a power
seat track assembly located under each front seat
(Fig. 7). The power seat track assembly replaces the
standard manually operated seat tracks. The lower
half of the power seat track is secured at the front
with two bolts to the floor panel seat cross member,
and at the rear with two bolts to the floor panel.
Four nuts secure the bottom of the seat cushion
frame to the upper half of the power seat track unit.
The power seat track assembly cannot be repaired,
and is serviced only as a complete assembly. If any
component in this assembly is faulty or damaged, the
entire power seat track must be replaced.
OPERATION
The power seat track unit includes three reversible
electric motors that are secured to the upper half of
the track unit. Each motor moves the seat adjuster
through a combination of worm-drive gearboxes and
screw-type drive units.
The front and rear of the seat are operated by two
separate vertical adjustment motors. These motors
can be operated independently of each other, tilting
the entire seat assembly forward or rearward; or,
they can be operated in unison by selecting the
proper power seat switch functions, which will raise
or lower the entire seat assembly. The third motor is
the horizontal adjustment motor, which moves the
seat track in the forward and rearward directions.
DIAGNOSIS AND TESTING - POWER SEAT
TRACK
For complete power seat circuit descriptions and
diagrams, refer to Wiring Diagrams.
Operate the power seat switch to move all three
seat motors in each direction. The seat should move
in each of the selected directions. If the power seat
track fails to operate in only one direction, move the
seat track a short distance in the opposite direction
and test again to be certain that the track is not at
its travel limit. If the power seat track still fails to
operate in only one direction, refer to Diagnosis and
Testing of the Power Seat Switch in this section. If
Fig. 6 Power Seat Switch Remove/Install
1 - SEAT SIDE SHIELD
2 - POWER SEAT SWITCH
3 - SCREWS
Fig. 7 DR Driver Power Seat Track
1 - POWER SEAT TRACK ASSEMBLY
2 - SEAT TRACK WIRE HARNESS
3 - SEAT BELT BUCKLE ASSEMBLIES
8N - 18 POWER SEATSDR
PASSENGER SEAT SWITCH (Continued)

(5) Coat the dust seal withhigh temp grease.
(6) Install the dust seal with a driver and handle
(Fig. 7).
(7) Install protective seal protector 8993 over the
shaft (Fig. 8).
(8) Install the pitman shaft into the steering gear
until it fully seats into the bearing.
(9) Install the new cover bolts and tighten to 68
N´m (50 ft. lbs.).
(10) Install the pitman arm (Refer to 19 - STEER-
ING/LINKAGE/PITMAN ARM - INSTALLATION).
INSTALLATION - DIESEL
NOTE: Generous amounts of the high temperature
grease from the seal kit should be applied to areas
between the pitman shaft bearing and oil seals and
also between the dust seals and snap ring.
(1) Coat the oil seal and washer withhigh temp
grease.
NOTE: Install the oil seal with the lip facing inward.
Flat side of the oil seal should be against the
washer.
(2) Install the oil seal with special tool 8989 driver
and C-4171 handle (Fig. 7).
(3) Install backup washer.
(4) Install the retainer ring with snap ring pliers.
(5) Coat the dust seal withhigh temp grease.
(6) Install the dust seal with special tool 8989
driver and C-4171 handle (Fig. 7).
(7) Install protective seal protector 8993 over the
shaft (Fig. 8).
(8) Install the pitman shaft into the steering gear
until it fully seats into the bearing.
(9) Install the new cover bolts and tighten to 68
N´m (50 ft. lbs.).
(10) Install the steering gear (Refer to 19 -
STEERING/GEAR - INSTALLATION).
(11) Install the pitman arm (Refer to 19 - STEER-
ING/LINKAGE/PITMAN ARM - INSTALLATION).
(12) Perform a wheel alignment (Refer to 2 - SUS-
PENSION/WHEEL ALIGNMENT - STANDARD
PROCEDURE).
STEERING GEAR INPUT
SHAFT SEAL
REMOVAL
(1) Remove the steering gear from the vehicle
(Refer to 19 - STEERING/GEAR - REMOVAL).
CAUTION: Do not overtighten the vise on the gear
case. This may affect the adjustment
(2) Mount the steering gear upside down over a
drain pan in a soft jawed vise.
(3) Place a drain pan under the gear and rotate
the input shaft back and forth several times lock-to-
lock to discharge the fluid from the steering gear
(4) Drain all the remaining fluid from the gear.
(5) Rotate the input shaft from stop to stop and
count the number of turns using a 12 point socket
(Fig. 9).
Fig. 7 SEAL INSTALLATION
1 - SPECIAL TOOL
C-4171
2 - SPECIAL TOOL
8989
3 - STEERING GEAR
Fig. 8 PITMAN SHAFT SEAL PROTECTOR
1 - STEERING GEAR
2 - SPECIAL TOOL
8993
DRGEAR - LINK/COIL 19 - 25
PITMAN SHAFT SEAL (Continued)

ABS - DESCRIPTION, BRAKES...........5-39
ABS - OPERATION, BRAKES.............5-39
ABS BRAKE BLEEDING - STANDARD
PROCEDURE.........................5-40
ABS INDICATOR - DESCRIPTION.........8J-17
ABS INDICATOR - OPERATION..........8J-17
A/C APPLICATION TABLE,
SPECIFICATIONS......................24-7
A/C COMPRESSOR CLUTCH -
DESCRIPTION........................24-9
A/C COMPRESSOR CLUTCH -
INSPECTION........................24-12
A/C COMPRESSOR CLUTCH -
INSTALLATION.......................24-12
A/C COMPRESSOR CLUTCH -
OPERATION..........................24-9
A/C COMPRESSOR CLUTCH - REMOVAL . . 24-10
A/C COMPRESSOR CLUTCH BREAK-IN -
STANDARD PROCEDURE...............24-10
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-10
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-13
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-14
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-13
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-14
A/C COMPRESSOR NOISE - DIAGNOSIS
AND TESTING.......................24-36
A/C CONDENSER - DESCRIPTION.........24-39
A/C CONDENSER - OPERATION..........24-39
A/C EVAPORATOR - DESCRIPTION.......24-47
A/C EVAPORATOR - INSTALLATION......24-47
A/C EVAPORATOR - OPERATION.........24-47
A/C EVAPORATOR - REMOVAL..........24-47
A/C HEATER CONTROL - DESCRIPTION . . . 24-14
A/C HEATER CONTROL - INSTALLATION . . . 24-15
A/C HEATER CONTROL - REMOVAL......24-14
A/C ORIFICE TUBE - DESCRIPTION.......24-48
A/C ORIFICE TUBE - INSTALLATION......24-49
A/C ORIFICE TUBE - OPERATION........24-48
A/C ORIFICE TUBE - REMOVAL..........24-49
A/C PERFORMANCE - DIAGNOSIS AND
TESTING............................24-2
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-15
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-15
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-16
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-15
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-16
ACCELERATOR PEDAL - INSTALLATION . . . 14-24
ACCELERATOR PEDAL - REMOVAL.......14-24
ACCELERATOR PEDAL POSITION
SENSOR - DESCRIPTION...............14-25
ACCELERATOR PEDAL POSITION
SENSOR - INSTALLATION..............14-25
ACCELERATOR PEDAL POSITION
SENSOR - OPERATION................14-25
ACCELERATOR PEDAL POSITION
SENSOR - REMOVAL..................14-25
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING................7-25,7-28,7-31
ACCUMULATOR - DESCRIPTION.........24-49
ACCUMULATOR - DESCRIPTION
. . 21-191,21-372
ACCUMULATOR - INSPECTION
. . . 21-192,21-373
ACCUMULATOR - INSTALLATION
........24-50
ACCUMULATOR - OPERATION
..........24-49
ACCUMULATOR - OPERATION
....21-192,21-373
ACCUMULATOR - REMOVAL
............24-49
ACM COVER - INSTALLATION
............8O-9
ACM COVER - REMOVAL
...............8O-9
ACTUATION TEST MODE - DESCRIPTION,
CIRCUIT
.............................25-1
ACTUATOR - DESCRIPTION, BLEND
DOOR
.............................24-16
ACTUATOR - DESCRIPTION, FUEL
CONTROL
..........................14-85
ACTUATOR - DESCRIPTION, MODE
DOOR
.............................24-20
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR
................24-22ACTUATOR - INSTALLATION, BLEND
DOOR.............................24-17
ACTUATOR - INSTALLATION, FLOOR -
DEFROST DOOR.....................24-20
ACTUATOR - INSTALLATION, FUEL
CONTROL..........................14-85
ACTUATOR - INSTALLATION, INSIDE
HANDLE.......................23-22,23-32
ACTUATOR - INSTALLATION, MODE
DOOR.............................24-22
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-23
ACTUATOR - OPERATION, BLEND DOOR . . 24-16
ACTUATOR - OPERATION, FUEL
CONTROL..........................14-85
ACTUATOR - OPERATION, MODE DOOR . . . 24-21
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-22
ACTUATOR - REMOVAL, BLEND DOOR....24-17
ACTUATOR - REMOVAL, FLOOR -
DEFROST DOOR.....................24-19
ACTUATOR - REMOVAL, FUEL CONTROL . . 14-85
ACTUATOR - REMOVAL, INSIDE HANDLE . 23-22,
23-31
ACTUATOR - REMOVAL, MODE DOOR....24-21
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-22
ADAPTER HOUSING SEAL -
INSTALLATION...........21-127,21-539,21-83
ADAPTER HOUSING SEAL - REMOVAL . . 21-127,
21-539,21-83
ADAPTER MOUNT - INSTALLATION, DISC
BRAKE CALIPER......................5-17
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE................7-19
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING..................7-19
ADHESIVE LOCATIONS -
SPECIFICATIONS, STRUCTURAL........23-113
ADJUSTABLE PEDAL MOTOR -
DESCRIPTION........................5-24
ADJUSTABLE PEDAL MOTOR -
INSTALLATION........................5-24
ADJUSTABLE PEDAL MOTOR - REMOVAL . . 5-24
ADJUSTABLE PEDAL SWITCH -
INSTALLATION.........................5-6
ADJUSTABLE PEDAL SWITCH -
REMOVAL............................5-6
ADJUSTER - DIAGNOSIS AND TESTING,
HYDRAULIC LASH................9-124,9-31
ADJUSTER - INSTALLATION, SEAT BELT
TURNING LOOP.....................8O-50
ADJUSTER - REMOVAL, SEAT BELT
TURNING LOOP.....................8O-50
ADJUSTER ASSEMBLY - DESCRIPTION,
ROCKER ARM.......................9-124
ADJUSTER ASSEMBLY - INSTALLATION,
ROCKER ARM..................9-124,9-249
ADJUSTER ASSEMBLY - REMOVAL,
ROCKER ARM..................9-124,9-249
ADJUSTER ASSY - CLEANING, ROCKER
ARM
..............................9-310
ADJUSTER ASSY - DESCRIPTION,
ROCKER ARM
.......................9-310
ADJUSTER ASSY - INSPECTION,
ROCKER ARM
.......................9-311
ADJUSTER ASSY - INSTALLATION,
ROCKER ARM
.............9-198,9-312,9-379
ADJUSTER ASSY - REMOVAL, ROCKER
ARM
....................9-198,9-310,9-379
ADJUSTING TOOL - ADJUSTMENT, WITH
. . . 5-36
AFTER A SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE
.................8O-7
AIR CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING
..........................21-494
AIR CLEANER ELEMENT - INSTALLATION
. 9-105,
9-20,9-242,9-298,9-370
AIR CLEANER ELEMENT - REMOVAL
. 9-105,9-20,
9-242,9-297,9-370
AIR CONDITIONER - DESCRIPTION,
HEATER
.............................24-1
AIR CONDITIONER - OPERATION,
HEATER
.............................24-1
AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE WITH
.......7-70AIR CONDITIONING - INSTALLATION,
WATER PUMP BYPASS HOSE
WITHOUT............................7-70
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITH.............7-68
AIR CONDITIONING - REMOVAL, WATER
PUMP BYPASS HOSE WITHOUT..........7-69
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-33
AIR CONTROL MOTOR - INSTALLATION,
IDLE...............................14-35
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-33
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-34
AIR COOLER AND PLUMBING -
CLEANING, CHARGE..................11-16
AIR COOLER AND PLUMBING -
DESCRIPTION, CHARGE...............11-15
AIR COOLER AND PLUMBING -
INSPECTION, CHARGE.................11-16
AIR COOLER AND PLUMBING -
INSTALLATION, CHARGE...............11-16
AIR COOLER AND PLUMBING -
OPERATION, CHARGE.................11-15
AIR COOLER AND PLUMBING -
REMOVAL, CHARGE..................11-15
AIR COOLER SYSTEM - LEAKS -
DIAGNOSIS AND TESTING, CHARGE......11-15
AIR DAM - INSTALLATION, FRONT........13-2
AIR DAM - REMOVAL, FRONT...........13-2
AIR HEATER - DESCRIPTION, INTAKE.....14-91
AIR HEATER - INSTALLATION, INTAKE....14-91
AIR HEATER - OPERATION, INTAKE......14-91
AIR HEATER - REMOVAL, INTAKE........14-91
AIR HEATER RELAY - DESCRIPTION,
INTAKE ............................14-92
AIR HEATER RELAY - INSTALLATION,
INTAKE ............................14-93
AIR HEATER RELAY - OPERATION,
INTAKE ............................14-92
AIR HEATER RELAY - REMOVAL, INTAKE . . 14-93
AIR INTAKE SYSTEM - INSTALLATION....9-194
AIR INTAKE SYSTEM - REMOVAL........9-194
AIR TEMPERATURE SENSOR -
DESCRIPTION, INTAKE................14-36
AIR TEMPERATURE SENSOR -
INSTALLATION, INTAKE................14-38
AIR TEMPERATURE SENSOR -
OPERATION, INTAKE..................14-36
AIR TEMPERATURE SENSOR -
REMOVAL, INTAKE...................14-36
AIR TEMPERATURE SENSOR/MAP
SENSOR - DESCRIPTION, INTAKE........14-93
AIR TEMPERATURE SENSOR/MAP
SENSOR - INSTALLATION, INTAKE.......14-94
AIR TEMPERATURE SENSOR/MAP
SENSOR - OPERATION, INTAKE.........14-93
AIR TEMPERATURE SENSOR/MAP
SENSOR - REMOVAL, INTAKE...........14-93
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - DESCRIPTION, INLET.........14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - INSTALLATION, INLET........14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - OPERATION, INLET..........14-90
AIR TEMPERATURE SENSOR/PRESSURE
SENSOR - REMOVAL, INLET............14-90
AIR TESTING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-143,21-324
AIR TO OIL COOLER - INSTALLATION.....7-75
AIR TO OIL COOLER - REMOVAL.........7-74
AIRBAG - DESCRIPTION, DRIVER........8O-22
AIRBAG - DESCRIPTION, PASSENGER....8O-34
AIRBAG - DESCRIPTION, SIDE CURTAIN . . 8O-51
AIRBAG - INSTALLATION, DRIVER.......8O-24
AIRBAG - INSTALLATION, PASSENGER . . . 8O-37
AIRBAG - INSTALLATION, SIDE CURTAIN . . 8O-53
AIRBAG - OPERATION, DRIVER.........8O-23
AIRBAG - OPERATION, PASSENGER......8O-35
AIRBAG - OPERATION, SIDE CURTAIN....8O-51
AIRBAG - REMOVAL, DRIVER
...........8O-23
AIRBAG - REMOVAL, PASSENGER
.......8O-35
AIRBAG - REMOVAL, SIDE CURTAIN
.....8O-52
AIRBAG CONTROL MODULE -
DESCRIPTION
.......................8O-10
AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE IMPACT
...........8O-53
DRINDEX 1
Description Group-Page Description Group-Page Description Group-Page

BACK LID - INSTALLATION, CENTER
SEAT ..............................23-80
BACK LID - REMOVAL, CENTER SEAT....23-80
BACK PANEL TRIM - INSTALLATION,
REAR CAB..........................23-70
BACK PANEL TRIM - REMOVAL, REAR
CAB ...............................23-70
BACK REAR - FOOTMANS LOOP
BRACKETS - INSTALLATION, SEAT.......23-85
BACK REAR - FOOTMANS LOOP
BRACKETS - REMOVAL, SEAT...........23-85
BACKLITE - INSTALLATION.............23-86
BACKLITE - REMOVAL.................23-86
BACKLITE VENT GLASS - INSTALLATION . . 23-87
BACKLITE VENT GLASS - REMOVAL......23-87
BACKUP LAMP - INSTALLATION..........8L-7
BACKUP LAMP - REMOVAL.............8L-7
BACKUP LAMP SWITCH - DESCRIPTION . . . 8L-7
BACKUP LAMP SWITCH - DIAGNOSIS
AND TESTING........................8L-8
BACKUP LAMP SWITCH - OPERATION.....8L-8
BALANCE - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-4
BALANCE SHAFT - INSTALLATION........9-79
BALANCE SHAFT - REMOVAL............9-79
BALL JOINT - DIAGNOSIS AND TESTING,
LOWER.............................2-18
BALL JOINT - DIAGNOSIS AND TESTING,
UPPER..............................2-26
BALL JOINT - INSTALLATION, LOWER . . 2-19,2-33
BALL JOINT - INSTALLATION, UPPER.....2-33
BALL JOINT - REMOVAL, LOWER.....2-18,2-32
BALL JOINT - REMOVAL, UPPER.........2-33
BAND OPERATION - DIAGNOSIS AND
TESTING, AIR TESTING
TRANSMISSION CLUTCH.......21-143,21-324
BANDS - ADJUSTMENT.........21-193,21-374
BANDS - DESCRIPTION.........21-193,21-373
BANDS - OPERATION..........21-193,21-374
BAR - DESCRIPTION, STABILIZER........2-24
BAR - DESCRIPTION, TORSION..........2-25
BAR - INSTALLATION, STABILIZER....2-24,2-37
BAR - INSTALLATION, TORSION..........2-26
BAR - INSTALLATION, TRACK...........19-37
BAR - OPERATION, STABILIZER..........2-24
BAR - OPERATION, TORSION............2-25
BAR - REMOVAL, STABILIZER.......2-24,2-37
BAR - REMOVAL, TORSION.............2-25
BAR - REMOVAL, TRACK..............19-37
BAR CROSS MEMBER BUSHING -
INSTALLATION, TORSION...............2-14
BAR CROSSMEMBER BUSHING -
REMOVAL, TORSION...................2-12
BASE BRAKE, SPECIFICATIONS............5-7
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-2
BASE BRAKES, SPECIAL TOOLS...........5-5
BASECOAT/CLEARCOAT FINISH -
DESCRIPTION.......................23-74
BATTERIES - STANDARD PROCEDURE,
RKE TRANSMITTER...................8N-9
BATTERY - DESCRIPTION...............8F-7
BATTERY - DIAGNOSIS AND TESTING.....8F-7
BATTERY CABLES - DESCRIPTION.......8F-14
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-15
BATTERY CABLES - INSTALLATION.......8F-17
BATTERY CABLES - OPERATION.........8F-14
BATTERY CABLES - REMOVAL..........8F-16
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY HOLDDOWN - DESCRIPTION....8F-14
BATTERY HOLDDOWN - INSTALLATION . . . 8F-14
BATTERY HOLDDOWN - OPERATION.....8F-14
BATTERY HOLDDOWN - REMOVAL.......8F-14
BATTERY SYSTEM - CLEANING...........8F-4
BATTERY SYSTEM - DESCRIPTION........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING............................8F-2
BATTERY SYSTEM - INSPECTION.........8F-6
BATTERY SYSTEM - OPERATION
.........8F-2
BATTERY SYSTEM - SPECIFICATIONS
......8F-6
BATTERY SYSTEM SPECIAL TOOLS,
SPECIAL TOOLS
......................8F-7
BATTERY TEMPERATURE SENSOR -
DESCRIPTION
.......................8F-21
BATTERY TEMPERATURE SENSOR -
INSTALLATION
.......................8F-21BATTERY TEMPERATURE SENSOR -
OPERATION.........................8F-21
BATTERY TEMPERATURE SENSOR -
REMOVAL..........................8F-21
BATTERY TESTER - STANDARD
PROCEDURE, USING MICRO 420........8F-12
BATTERY TRAY - DESCRIPTION.........8F-17
BATTERY TRAY - INSTALLATION.........8F-18
BATTERY TRAY - OPERATION...........8F-17
BATTERY TRAY - REMOVAL............8F-17
BEAM INDICATOR - DESCRIPTION, HIGH . . 8J-27
BEAM INDICATOR - OPERATION, HIGH....8J-28
BEARING - ADJUSTMENTS, CENTER.......3-8
BEARING - FITTING - STANDARD
PROCEDURE, CRANKSHAFT MAIN . . 9-133,9-202
BEARING - INSTALLATION, CENTER........3-8
BEARING - INSTALLATION, CLUTCH
RELEASE............................6-11
BEARING - INSTALLATION, HUB..........2-31
BEARING - INSTALLATION, OUTPUT
SHAFT FRONT................21-217,21-395
BEARING - INSTALLATION, OUTPUT
SHAFT REAR.................21-217,21-396
BEARING - INSTALLATION, PILOT........6-12
BEARING - REMOVAL, CENTER...........3-8
BEARING - REMOVAL, CLUTCH RELEASE . . . 6-11
BEARING - REMOVAL, HUB.............2-30
BEARING - REMOVAL, OUTPUT SHAFT
FRONT......................21-217,21-395
BEARING - REMOVAL, OUTPUT SHAFT
REAR.......................21-217,21-395
BEARING - REMOVAL, PILOT............6-12
BEARING AND CRANKSHAFT JOURNAL
CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD........9-321
BEARING CLEARANCE - STANDARD
PROCEDURE, MAIN...................9-322
BEARING FITTING - STANDARD
PROCEDURE, CONNECTING ROD . . . 9-128,9-251,
9-382
BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT MAIN.......9-253
BEARING FITTING, STANDARD
PROCEDURE - CONNECTING ROD........9-48
BEARING FITTING, STANDARD
PROCEDURE - MAIN...................9-43
BEARINGS - DESCRIPTION,
CRANKSHAFT MAIN..................9-253
BEARINGS - INSPECTION, CRANKSHAFT
MAIN.........................9-133,9-203
BEARINGS - INSTALLATION, AXLE . . 3-112,3-139,
3-34,3-84
BEARINGS - INSTALLATION, CAMSHAFT . . 9-320,
9-381
BEARINGS - INSTALLATION,
CRANKSHAFT MAIN.............9-254,9-383
BEARINGS - INSTALLATION,
DIFFERENTIAL CASE . 3-121,3-148,3-39,3-65,3-94
BEARINGS - OPERATION, CRANKSHAFT
MAIN..............................9-253
BEARINGS - REMOVAL, AXLE . 3-112,3-138,3-33,
3-84
BEARINGS - REMOVAL, CAMSHAFT . 9-317,9-380
BEARINGS - REMOVAL, CRANKSHAFT
MAIN.........................9-254,9-383
BEARINGS - REMOVAL, DIFFERENTIAL
CASE.............3-121,3-148,3-39,3-64,3-93
BEARINGS - STANDARD PROCEDURE,
FITTING CRANKSHAFT MAIN...........9-383
BELT / CHAIN COVER(S) -
INSTALLATION, TIMING . 9-169,9-278,9-404,9-81
BELT / CHAIN COVER(S) - REMOVAL,
TIMING..............9-168,9-278,9-404,9-80
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE............7-25,7-28,7-31
BELT - INSTALLATION, FRONT CENTER
SEAT ..............................8O-27
BELT - REMOVAL, FRONT CENTER SEAT . . 8O-26
BELT & RETRACTOR - INSTALLATION,
FRONT CENTER SEAT
.................8O-26
BELT & RETRACTOR - INSTALLATION,
REAR CENTER SEAT
..................8O-40
BELT & RETRACTOR - INSTALLATION,
REAR OUTBOARD SEAT
...............8O-42
BELT & RETRACTOR - REMOVAL, FRONT
CENTER SEAT
.......................8O-25
BELT & RETRACTOR - REMOVAL, REAR
CENTER SEAT
.......................8O-39BELT & RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT....................8O-41
BELT BUCKLE - INSTALLATION, FRONT
OUTBOARD SEAT....................8O-34
BELT BUCKLE - REMOVAL, FRONT
OUTBOARD SEAT....................8O-33
BELT MOLDING - INSTALLATION, FRONT
DOOR INNER........................23-93
BELT MOLDING - INSTALLATION, FRONT
DOOR OUTER.......................23-93
BELT MOLDING - INSTALLATION, REAR
DOOR INNER........................23-94
BELT MOLDING - INSTALLATION, REAR
DOOR OUTER.......................23-94
BELT MOLDING - REMOVAL, FRONT
DOOR INNER........................23-93
BELT MOLDING - REMOVAL, FRONT
DOOR OUTER.......................23-93
BELT MOLDING - REMOVAL, REAR
DOOR INNER........................23-94
BELT MOLDING - REMOVAL, REAR
DOOR OUTER.......................23-94
BELT SWITCH - DESCRIPTION, SEAT.....8O-46
BELT SWITCH - DIAGNOSIS AND
TESTING, SEAT......................8O-47
BELT SWITCH - OPERATION, SEAT.......8O-46
BELT TENSION REDUCER -
DESCRIPTION, SEAT..................8O-48
BELT TENSION REDUCER - DIAGNOSIS
AND TESTING, SEAT..................8O-49
BELT TENSION REDUCER - OPERATION,
SEAT ..............................8O-49
BELT TENSIONER - DESCRIPTION, SEAT....8O-47
BELT TENSIONER - OPERATION, SEAT....8O-48
BELT TENSIONERS - 3.7L / 4.7L -
DESCRIPTION........................7-22
BELT TENSIONERS - 3.7L / 4.7L -
INSTALLATION........................7-23
BELT TENSIONERS - 3.7L / 4.7L -
OPERATION..........................7-22
BELT TENSIONERS - 3.7L / 4.7L -
REMOVAL...........................7-22
BELT TENSIONERS - 5.9L -
DESCRIPTION........................7-23
BELT TENSIONERS - 5.9L -
INSTALLATION........................7-24
BELT TENSIONERS - 5.9L - OPERATION....7-23
BELT TENSIONERS - 5.9L - REMOVAL.....7-23
BELT TENSIONERS - 5.9L DIESEL -
DESCRIPTION........................7-24
BELT TENSIONERS - 5.9L DIESEL -
INSTALLATION........................7-25
BELT TENSIONERS - 5.9L DIESEL -
OPERATION..........................7-24
BELT TENSIONERS - 5.9L DIESEL -
REMOVAL...........................7-25
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT.................8O-50
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT.....................8O-50
BELT/CHAIN AND SPROCKETS -
INSPECTION, TIMING.............9-171,9-83
BELT/CHAIN AND SPROCKETS -
INSTALLATION, TIMING . 9-172,9-279,9-406,9-84
BELT/CHAIN AND SPROCKETS -
REMOVAL, TIMING.....9-169,9-279,9-405,9-81
BELTS - 3.7L / 4.7L - INSTALLATION,
DRIVE..............................7-27
BELTS - 3.7L / 4.7L - REMOVAL, DRIVE....7-27
BELTS - 5.9L - INSTALLATION, DRIVE.....7-31
BELTS - 5.9L - REMOVAL, DRIVE.........7-30
BELTS - 5.9L DIESEL - INSTALLATION,
DRIVE..............................7-34
BELTS - 5.9L DIESEL - REMOVAL, DRIVE . . 7-34
BEZEL - INSTALLATION, CLUSTER.......23-50
BEZEL - INSTALLATION, INSTRUMENT
PANEL CENTER......................23-58
BEZEL - INSTALLATION, INSTRUMENT
PANEL DRIVER SIDE..................23-59
BEZEL - INSTALLATION, INSTRUMENT
PANEL HEADLAMP SWITCH
............23-57
BEZEL - REMOVAL, CLUSTER
...........23-50
BEZEL - REMOVAL, INSTRUMENT PANEL
CENTER
............................23-58
BEZEL - REMOVAL, INSTRUMENT PANEL
DRIVER SIDE
........................23-58
BEZEL - REMOVAL, INSTRUMENT PANEL
HEADLAMP SWITCH
..................23-57
DRINDEX 3
Description Group-Page Description Group-Page Description Group-Page

INDICATOR - DESCRIPTION, UPSHIFT....8J-40
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-42
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-42
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-43
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-19
INDICATOR - OPERATION, ABS..........8J-17
INDICATOR - OPERATION, AIRBAG.......8J-18
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-19
INDICATOR - OPERATION, CARGO LAMP . . 8J-20
INDICATOR - OPERATION, CHECK
GAUGES............................8J-21
INDICATOR - OPERATION, CRUISE.......8J-22
INDICATOR - OPERATION, DOOR AJAR . . . 8J-23
INDICATOR - OPERATION, ETC..........8J-25
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-27
INDICATOR - OPERATION, HIGH BEAM....8J-28
INDICATOR - OPERATION, LAMP OUT....8J-28
INDICATOR - OPERATION, LOW FUEL.....8J-29
INDICATOR - OPERATION, OVERDRIVE
OFF ...............................8J-33
INDICATOR - OPERATION, SEATBELT.....8J-34
INDICATOR - OPERATION, SECURITY.....8J-35
INDICATOR - OPERATION, SERVICE 4WD . . 8J-36
INDICATOR - OPERATION, TRANS TEMP . . 8J-38
INDICATOR - OPERATION, TURN SIGNAL . . 8J-39
INDICATOR - OPERATION, UPSHIFT......8J-40
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-42
INDICATOR - OPERATION, WASHER
FLUID..............................8J-42
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-43
INDICATOR LAMP - DESCRIPTION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP - OPERATION,
SENTRY KEY IMMOBILIZER SYSTEM......8Q-5
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-30
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-30
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-7
INERTIA HINGE COVER - INSTALLATION,
CENTER SEAT BACK..................23-78
INERTIA HINGE COVER - REMOVAL,
CENTER SEAT BACK..................23-78
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-6
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE................8M-10
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-8
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE...........................8M-10
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-39
INITIALIZATION, STANDARD PROCEDURE
- SENTRY KEY IMMOBILIZER SYSTEM....8Q-3
INJECTION PUMP - DESCRIPTION, FUEL . . 14-64
INJECTION PUMP - INSTALLATION, FUEL . 14-67
INJECTION PUMP - OPERATION, FUEL
....14-64
INJECTION PUMP - REMOVAL, FUEL
.....14-65
INJECTION PUMP TIMING - DIAGNOSIS
AND TESTING, FUEL
..................14-65
INJECTOR - DESCRIPTION, FUEL
. . . 14-32,14-85
INJECTOR - INSTALLATION, FUEL
........14-87
INJECTOR - OPERATION, FUEL
.....14-32,14-86
INJECTOR - REMOVAL, FUEL
...........14-87
INJECTOR FIRING ORDER, DIESEL -
FUEL
..............................14-60
INJECTOR RAIL - DESCRIPTION, FUEL
....14-89
INJECTOR RAIL - INSTALLATION, FUEL
. . . 14-90
INJECTOR RAIL - OPERATION, FUEL
.....14-89
INJECTOR RAIL - REMOVAL, FUEL
.......14-89
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - DESCRIPTION
.....14-90INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - INSTALLATION.....14-90
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - OPERATION.......14-90
INLET AIR TEMPERATURE SENSOR/
PRESSURE SENSOR - REMOVAL........14-90
INLET FILTER - INSTALLATION..........14-23
INLET FILTER - REMOVAL..............14-23
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR.......................23-93
INNER BELT MOLDING - INSTALLATION,
REAR DOOR........................23-94
INNER BELT MOLDING - REMOVAL,
FRONT DOOR.......................23-93
INNER BELT MOLDING - REMOVAL,
REAR DOOR........................23-94
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-6
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-552
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-549
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-550
INPUT CLUTCH ASSEMBLY - OPERATION . 21-549
INPUT SHAFT SEAL - INSTALLATION,
STEERING GEAR.....................19-28
INPUT SHAFT SEAL - REMOVAL,
STEERING GEAR.....................19-25
INPUT SPEED SENSOR - DESCRIPTION . . 21-558
INPUT SPEED SENSOR - INSTALLATION . 21-559
INPUT SPEED SENSOR - OPERATION....21-558
INPUT SPEED SENSOR - REMOVAL.......21-559
INSERTS - INSTALLATION, SPRING TIP....2-42
INSERTS - REMOVAL, SPRING TIP........2-41
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-22,23-32
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-22,
23-31
INSTALLED - INSTALLATION, FRONT OIL
SEAL - FRONT COVER.................9-384
INSTALLED - REMOVAL, FRONT OIL
SEAL - FRONT COVER.................9-384
INSTRUMENT CLUSTER - ASSEMBLY.....8J-15
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING.......................8J-10
INSTRUMENT CLUSTER - DISASSEMBLY . . 8J-14
INSTRUMENT CLUSTER - INSTALLATION . . 8J-16
INSTRUMENT CLUSTER - OPERATION.....8J-6
INSTRUMENT CLUSTER - REMOVAL.....8J-14
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-7
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-6
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-56
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-53
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-58
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-58
INSTRUMENT PANEL DRIVER SIDE
BEZEL - INSTALLATION................23-59
INSTRUMENT PANEL DRIVER SIDE
BEZEL - REMOVAL...................23-58
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-29
INSTRUMENT PANEL DUCTS - REMOVAL . 24-29
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - INSTALLATION.........23-57
INSTRUMENT PANEL HEADLAMP
SWITCH BEZEL - REMOVAL............23-57
INSTRUMENT PANEL LOWER
SURROUND - INSTALLATION...........23-60
INSTRUMENT PANEL LOWER
SURROUND - REMOVAL...............23-60
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-60
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-59
INTAKE AIR HEATER - DESCRIPTION.....14-91
INTAKE AIR HEATER - INSTALLATION
.....14-91
INTAKE AIR HEATER - OPERATION
.......14-91
INTAKE AIR HEATER - REMOVAL
........14-91
INTAKE AIR HEATER RELAY -
DESCRIPTION
.......................14-92
INTAKE AIR HEATER RELAY -
INSTALLATION
.......................14-93INTAKE AIR HEATER RELAY -
OPERATION.........................14-92
INTAKE AIR HEATER RELAY - REMOVAL . . 14-93
INTAKE AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-36
INTAKE AIR TEMPERATURE SENSOR -
INSTALLATION.......................14-38
INTAKE AIR TEMPERATURE SENSOR -
OPERATION.........................14-36
INTAKE AIR TEMPERATURE SENSOR -
REMOVAL..........................14-36
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - DESCRIPTION..........14-93
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - INSTALLATION..........14-94
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - OPERATION............14-93
INTAKE AIR TEMPERATURE SENSOR/
MAP SENSOR - REMOVAL.............14-93
INTAKE MANIFOLD - CLEANING....9-158,9-219,
9-275,9-346,9-402
INTAKE MANIFOLD - DESCRIPTION . 9-157,9-219,
9-274,9-401,9-71
INTAKE MANIFOLD - INSPECTION . . 9-158,9-219,
9-275,9-346,9-402
INTAKE MANIFOLD - INSTALLATION.....9-158,
9-219,9-275,9-346,9-402,9-72
INTAKE MANIFOLD - OPERATION........9-274
INTAKE MANIFOLD - REMOVAL....9-157,9-219,
9-275,9-345,9-401,9-72
INTAKE MANIFOLD LEAKAGE -
DIAGNOSIS AND TESTING . . . 9-157,9-219,9-274,
9-401
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-71
INTAKE SYSTEM - INSTALLATION, AIR....9-194
INTAKE SYSTEM - REMOVAL, AIR.......9-194
INTAKE/EXHAUST VALVES & SEATS -
CLEANING..........................9-248
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION....9-122,9-246,9-27,9-305,9-375
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION........................9-248
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..............9-123,9-248,9-29
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.................9-122,9-248,9-28
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-3
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-4
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-3
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-3
INTERIOR - CAUTION.................23-63
INTERLOCK - ADJUSTMENTS, BRAKE
TRANSMISSION SHIFT . . . 21-195,21-376,21-540
INTERLOCK - DIAGNOSIS AND TESTING,
BRAKE TRANSMISSION SHIFT . . . 21-195,21-375,
21-540
INTERLOCK SYSTEM - DESCRIPTION,
BRAKE TRANSMISSION SHIFT . . . 21-194,21-375,
21-540
INTERLOCK SYSTEM - OPERATION,
BRAKE TRANSMISSION SHIFT . . . 21-194,21-375,
21-540
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-6
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.....9-178,9-225,
9-353,9-4,9-93
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-7
IOD FUSE - DESCRIPTION...........8W-97-6
IOD FUSE - INSTALLATION...........8W-97-7
IOD FUSE - OPERATION.............8W-97-6
IOD FUSE - REMOVAL..............8W-97-6
ISO FLARING - STANDARD PROCEDURE....5-7
ISOLATORS - INSTALLATION, BODY
......23-37
ISOLATORS - REMOVAL, BODY
.........23-36
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL
........................2-18
JOINT - DIAGNOSIS AND TESTING,
UPPER BALL
.........................2-26
JOINT - INSTALLATION, LOWER BALL
. 2-19,2-33
18 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

OVERDRIVE UNIT - DISASSEMBLY.....21-220,
21-399
OVERDRIVE UNIT - INSPECTION . 21-227,21-406
OVERDRIVE UNIT - INSTALLATION.....21-236,
21-414
OVERDRIVE UNIT - REMOVAL . . . 21-220,21-398
OVERFLOW VALVE - DESCRIPTION,
CASCADE...........................14-77
OVERFLOW VALVE - OPERATION,
CASCADE...........................14-77
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - DIAGNOSIS AND
TESTING............................8M-2
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE REMOVAL,
REMOVAL...........................8M-5
OVERHEAD CONSOLE, SPECIAL TOOLS . . . 8M-6
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
ASSEMBLY...................21-239,21-416
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
CLEANING...................21-238,21-416
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DESCRIPTION................21-237,21-415
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
DISASSEMBLY................21-238,21-415
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
INSPECTION.................21-238,21-416
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON RETAINER -
OPERATION..................21-237,21-415
OXYGEN SENSOR - DESCRIPTION.......14-43
OXYGEN SENSOR - INSTALLATION.......14-45
OXYGEN SENSOR - OPERATION.........14-43
OXYGEN SENSOR - REMOVAL..........14-44
PADS/SHOES - INSTALLATION, BRAKE.....5-10
PADS/SHOES - REMOVAL, BRAKE........5-10
PAINT CODE - DESCRIPTION...........23-74
PAINT CODES - SPECIFICATIONS........23-74
PAINT TOUCH-UP - DESCRIPTION.......23-75
PAINT TOUCH-UP - STANDARD
PROCEDURE........................23-75
PAN - CLEANING, OIL . . . 9-270,9-342,9-397,9-65
PAN - DESCRIPTION, OIL...............9-65
PAN - INSPECTION, OIL . 9-271,9-342,9-397,9-66
PAN - INSTALLATION, OIL . . . 9-153,9-217,9-271,
9-342,9-398,9-66
PAN - REMOVAL, OIL . . 9-153,9-217,9-270,9-342,
9-397,9-65
PANEL - INSTALLATION, TRIM.....23-24,23-33
PANEL - REMOVAL, TRIM.........23-24,23-33
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-7
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-6
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT.......................23-56
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT.......................23-53
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT
.......................23-58
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT
.......................23-58
PANEL DRIVER SIDE BEZEL -
INSTALLATION, INSTRUMENT
...........23-59
PANEL DRIVER SIDE BEZEL - REMOVAL,
INSTRUMENT
.......................23-58
PANEL DUCTS - INSTALLATION,
INSTRUMENT
.......................24-29
PANEL DUCTS - REMOVAL,
INSTRUMENT
.......................24-29
PANEL HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT
...........23-57
PANEL HEADLAMP SWITCH BEZEL -
REMOVAL, INSTRUMENT
..............23-57
PANEL LOWER SURROUND -
INSTALLATION, INSTRUMENT
...........23-60
PANEL LOWER SURROUND - REMOVAL,
INSTRUMENT
.......................23-60
PANEL OUTLETS - INSTALLATION
.......24-24
PANEL OUTLETS - REMOVAL
...........24-24
PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC BODY
............23-3PANEL TOP COVER - INSTALLATION,
INSTRUMENT.......................23-60
PANEL TOP COVER - REMOVAL,
INSTRUMENT.......................23-59
PANEL TRIM - INSTALLATION, REAR
CAB BACK..........................23-70
PANEL TRIM - REMOVAL, REAR CAB
BACK..............................23-70
PARK BRAKE CABLE - INSTALLATION,
REAR...............................5-32
PARK BRAKE CABLE - REMOVAL, REAR . . . 5-31
PARK LAMP RELAY - DESCRIPTION......8L-19
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-20
PARK LAMP RELAY - INSTALLATION.....8L-21
PARK LAMP RELAY - OPERATION.......8L-19
PARK LAMP RELAY - REMOVAL.........8L-20
PARKING BRAKE - DESCRIPTION.........5-30
PARKING BRAKE - OPERATION...........5-30
PARKING BRAKE CABLE -
INSTALLATION, FRONT.................5-32
PARKING BRAKE CABLE - REMOVAL,
FRONT..............................5-31
PARKING BRAKE SHOES - ADJUSTMENT . . . 5-34
PARK/TURN SIGNAL LAMP -
INSTALLATION.......................8L-21
PARK/TURN SIGNAL LAMP - REMOVAL . . . 8L-21
PARTS - STANDARD PROCEDURES,
CLEANING FUEL SYSTEM..............14-58
PASSENGER AIRBAG - DESCRIPTION....8O-34
PASSENGER AIRBAG - INSTALLATION....8O-37
PASSENGER AIRBAG - OPERATION......8O-35
PASSENGER AIRBAG - REMOVAL........8O-35
PASSENGER AIRBAG ON/OFF SWITCH -
DESCRIPTION.......................8O-38
PASSENGER AIRBAG ON/OFF SWITCH -
INSTALLATION......................8O-39
PASSENGER AIRBAG ON/OFF SWITCH -
OPERATION.........................8O-38
PASSENGER AIRBAG ON/OFF SWITCH -
REMOVAL..........................8O-39
PASSENGER SEAT SWITCH -
DESCRIPTION.......................8N-16
PASSENGER SEAT SWITCH - DIAGNOSIS
AND TESTING.......................8N-17
PASSENGER SEAT SWITCH -
INSTALLATION......................8N-18
PASSENGER SEAT SWITCH - OPERATION . 8N-17
PASSENGER SEAT SWITCH - REMOVAL . . . 8N-17
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION...................8E-8
PCM - OPERATION...................8E-11
PCM INPUT - OPERATION, ASD SENSE.....8I-6
PCM OUTPUT - DESCRIPTION............8I-6
PCM OUTPUT - OPERATION............14-32
PCM OUTPUT - OPERATION.............8I-6
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE........................8E-14
PCV VALVE - 3.7L V-6/ 4.7L V-8 -
DIAGNOSIS AND TESTING.............25-19
PCV VALVE - 5.9L V-8 - DIAGNOSIS AND
TESTING...........................25-19
PCV VALVE - DESCRIPTION............25-16
PCV VALVE - OPERATION..............25-17
PEDAL - DESCRIPTION.................5-22
PEDAL - INSTALLATION
............5-23,5-36
PEDAL - INSTALLATION, ACCELERATOR
. . . 14-24
PEDAL - OPERATION
...................5-22
PEDAL - REMOVAL
................5-23,5-36
PEDAL - REMOVAL, ACCELERATOR
......14-24
PEDAL MOTOR - DESCRIPTION,
ADJUSTABLE
.........................5-24
PEDAL MOTOR - INSTALLATION,
ADJUSTABLE
.........................5-24
PEDAL MOTOR - REMOVAL,
ADJUSTABLE
.........................5-24
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR
..........14-25
PEDAL POSITION SENSOR -
INSTALLATION, ACCELERATOR
..........14-25
PEDAL POSITION SENSOR - OPERATION,
ACCELERATOR
.......................14-25
PEDAL POSITION SENSOR - REMOVAL,
ACCELERATOR
.......................14-25
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH
.................6-14PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-14
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-14
PEDAL SWITCH - INSTALLATION,
ADJUSTABLE..........................5-6
PEDAL SWITCH - REMOVAL,
ADJUSTABLE..........................5-6
PER MILE, SPECIFICATIONS - TIRE
REVOLUTIONS.......................22-10
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS.....9-179,9-226,
9-354,9-4,9-89
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-5
PILOT BEARING - INSTALLATION.........6-12
PILOT BEARING - REMOVAL.............6-12
PINION GEAR/RING GEAR -
INSTALLATION....................3-42,3-66
PINION GEAR/RING GEAR - REMOVAL . 3-40,3-65
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION..............3-123,3-150,3-96
PINION GEAR/RING GEAR/TONE RING -
REMOVAL.................3-122,3-149,3-94
PINION SEAL - INSTALLATION . 3-113,3-140,3-35,
3-60,3-85
PINION SEAL - REMOVAL....3-113,3-140,3-34,
3-60,3-85
PIPE - INSPECTION, EXHAUST...........11-7
PIPE - INSTALLATION, EXHAUST.........11-7
PIPE - REMOVAL, EXHAUST.............11-7
PISTON & CONNECTING ROD -
CLEANING...........9-138,9-206,9-261,9-389
PISTON & CONNECTING ROD -
DESCRIPTION . . . 9-137,9-205,9-260,9-329,9-388,
9-47
PISTON & CONNECTING ROD -
INSPECTION.........9-138,9-206,9-261,9-389
PISTON & CONNECTING ROD -
INSTALLATION........9-139,9-207,9-261,9-389
PISTON & CONNECTING ROD -
REMOVAL......9-137,9-205,9-261,9-330,9-389
PISTON AND CONNECTING ROD -
CLEANING..........................9-331
PISTON FITTING - STANDARD
PROCEDURE.....9-137,9-205,9-260,9-389,9-50
PISTON RETAINER - ASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-239,21-416
PISTON RETAINER - CLEANING,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-238,21-416
PISTON RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-237,21-415
PISTON RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-238,21-415
PISTON RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-238,21-416
PISTON RETAINER - OPERATION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE..................21-237,21-415
PISTON RING FITTING - STANDARD
PROCEDURE.....9-140,9-207,9-262,9-333,9-52
PISTON RINGS - STANDARD
PROCEDURE, FITTING.................9-390
PISTONS - DESCRIPTION . 21-241,21-418,21-569
PISTONS - INSPECTION...............9-331
PISTONS - OPERATION . . . 21-241,21-418,21-569
PITMAN ARM - INSTALLATION..........19-36
PITMAN ARM - REMOVAL.............19-35
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-573
PLANETARY GEARTRAIN - CLEANING....21-573
PLANETARY GEARTRAIN - DESCRIPTION . 21-571
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-573
PLANETARY GEARTRAIN - INSPECTION
. . 21-573
PLANETARY GEARTRAIN - OPERATION
. . 21-571
PLANETARY GEARTRAIN/OUTPUT SHAFT
- ASSEMBLY
.................21-245,21-423
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DESCRIPTION
...............21-242,21-420
PLANETARY GEARTRAIN/OUTPUT SHAFT
- DISASSEMBLY
..............21-243,21-421
24 INDEXDR
Description Group-Page Description Group-Page Description Group-Page