ABS DODGE RAM SRT-10 2006 Service Repair Manual

C-PILLAR LOWER TRIM
REMOVAL
1. Remove the upper C-pillar trim panel (Refer to 23 -
BODY/INTERIOR/C-PILLAR TRIM - REMOVAL).
2. Remove the bolt (3) that secures the seat belt (2)
to the bottom of the C-pillar (4) and position the
seat belt out of the way.
3. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the lower C-pillar trim
panel (1) to the C-pillar.
4. Remove the seat belt from the lower C-pillar trim
panel through the slot provided and remove the
trim panel.
INSTALLATION
1. Route the seat belt (2) through the slot in the lower
C-pillar trim panel (1) and position the trim panel to
the C-pillar (4).
2. Engage the retaining tabs that secure the lower
C-pillar trim panel to the C-pillar.
3. Install the bolt (3) that secures the seat belt to the
bottom of the C-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the upper C-pillar trim panel (Refer to 23 -
BODY/INTERIOR/C-PILLAR UPPER TRIM -
INSTALLATION).

C-PILLAR UPPER TRIM
REMOVAL
1. Remove the cap (1) and then the bolt (2) that
secures the seat belt (3) to the top of the C-pillar
(4) and position the seat belt out of the way.
2. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper C-pillar
trim panel (5) to the C-pillar and remove the trim
panel.
INSTALLATION
1. Position the upper C-pillar trim panel (5) to the
C-pillar (4).
2. Engage the retaining tabs that secure the upper
C-pillar trim panel to the C-pillar.
3. Install the bolt (2) that secures the seat belt (3) to
the top of the C-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the cap (1) onto the seat belt.

COWL TRIM
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs of the cowl trim panel (1) from
the retainer clips (2) in the door sill (3).
2. Pull the cowl trim panel rearward and remove it
from the vehicle.
INSTALLATION
1. Position the cowl trim panel (1) onto the door sill
(3).
2. Push the cowl trim panel forward and then engage
the retaining tabs that secure the sill trim panel to
the rear door sill.

REAR DOOR SILL TRIM COVER
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs of the sill trim panel (1) from the
retainer clips in the rear door sill (2) and remove
the trim panel.
INSTALLATION
1. Position the sill trim panel (1) onto the rear door sill
(2).
2. Engage the retaining tabs that secure the sill trim
panel to the rear door sill.

BODY VENT
REMOVAL
1. Remove the rear cab trim panel (Refer to 23 -
BODY/INTERIOR/REAR CAB BACK PANEL TRIM
- REMOVAL)
2. Disengage the retaining tabs (1) that secure the
body vent (3) to the cab back panel (2).
3. Remove the vent through the opening in the cab
back panel.
INSTALLATION
1. Position the body vent (3) into the opening of the
cab back panel (2).
2. Install the body vent into the cab back panel and
fully engage the retaining tabs (1).
3. Install the rear cab trim panel (Refer to 23 - BODY/
INTERIOR/REAR CAB BACK PANEL TRIM -
INSTALLATION).

INSTALLATION
NOTE: Free pivot hinge cover is installed with the
free pivot hinge (Refer to 23 - BODY/SEATS/CEN-
TER SEAT BACK HINGE - INSTALLATION).
1. Position the hinge cover (1) over the hinge (2) and
close over the lock tabs (3).
2. Install the pivot bolt (5) and tighten to 10 Nꞏm (89
in. lbs.).
3. Reposition the storage bin/cushion cover (4).
4. Connect the zip strip (1).

6. Set glass (1) on lower fence and move glass for-
ward into opening.
7. Firmly push glass (1) against rear window glass
opening fence.
8. Bend tabs around edges of backlite opening fence
to retain glass.
9. Clean excess urethane from exterior with MOPAR
,
Super Clean or equivalent.
10. Allow urethane to cure at least 24 hours (full cure
is 72 hours).
11. Water test to verify repair before returning vehicle
to service.
12. Connect the rear window defogger electrical con-
nector, if equipped.
13. On standard cab models, install the upper b-pillar
trim (5) (Refer to 23 - BODY/INTERIOR/B-PILLAR
UPPER TRIM - INSTALLATION).
14. On quad cab models, install the upper c-pillar trim
(5) (Refer to 23 - BODY/INTERIOR/C-PILLAR
UPPER TRIM - INSTALLATION).

COVER-GUIDE MECHANISM
REMOVAL
1. Move the glass panel to the full closed position.
2. Slide sunshade rearward to the open position.
3. Separate the mechanism covers (2) from the tabs
(1) on the glass panel.
4. Hold both mechanism covers down and open the
sunroof fully.
5. Slide the mechanism covers (1) out the front of the
guide in the frame (2).

GLASS
REMOVAL
1. Move the glass panel to the full closed position.
2. Slide sunshade rearward to the open position.
3. Separate the mechanism covers (2) from the tabs
(1) on the glass panel.
4. Remove the glass panel screws (3).
5. Lift off glass panel and remove from vehicle.

INSTALLATION
1. Position glass panel on to mechanism lift arms.
CAUTION: Verify that the retaining tabs are located on the INSIDE of the guide mechanism arms.
2. Start the attaching screws (3).
3. Connect a 12v power supply and verify that the sunroof is in the closed position.
4. Adjust sunroof glass to fit flushwith roof line (Refer to 23 - BODY/SUNROOF/GLASS PANEL - ADJUSTMENTS).
5. Tighten the screws (3) to 3.5 Nꞏm (30 in. lbs.).
6. Position the mechanism covers (2) over the glass tabs (1) between the locating features and seat fully.
7. Verify sunroof operation and alignment.