light DODGE SPRINTER 2006 1.G Manual PDF

252 MAINTAINING YOUR VEHICLE
…Headlamps, Taillamps, Identification Lamps,
Turn Signal Lenses . . . . . . . . . . . . . . . . . . . . . . . 273
…Reversing Aid Sensors . . . . . . . . . . . . . . . . . . . . 273
…Window Cleaning . . . . . . . . . . . . . . . . . . . . . . . 274
…Wiper Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
…Light Alloy Wheels . . . . . . . . . . . . . . . . . . . . . . 275
…Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . 275
…Steering Wheel and Gear Selector Lever . . . . 275
…Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
…Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
…Headliner and Shelf Below Rear Window . . . 275
…Upholstery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
…Hard Plastic Trim Items . . . . . . . . . . . . . . . . . . 276
…Plastic and Rubber Parts . . . . . . . . . . . . . . . . . . 276
Q Electrical Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
…Standard Fuse and Relay Equipment . . . . . . . 277
…Relay Assignment, Standard Equipment . . . . 281
…Fuse and Relay Optional Equipment . . . . . . . 281
Q Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 284
…Front Lamp Unit . . . . . . . . . . . . . . . . . . . . . . . . . 284
…Taillamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
…License Plate Lamps
(Cargo/Passenger Vans Only) . . . . . . . . . . . . . 291
…Additional Brake Lamp
(Cargo/Passenger Vans Only) . . . . . . . . . . . . . 291
…Side-Mounted Turn Signals . . . . . . . . . . . . . . . 292
…Side-Marker Lamps,
Standing Lamps (Optional) . . . . . . . . . . . . . . . . 292
…Identification Lamps
(Cargo/passenger vans only) . . . . . . . . . . . . . . 293
…Interior Lighting in Passenger
Compartment and Load Compartment . . . . . 293
…Interior Lighting with Reading Lamp . . . . . . . 294
…Interior Lighting with Interior Sensor
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
…Exit Lamps (Optional) . . . . . . . . . . . . . . . . . . . . 295
Q Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
…Recommended Fluids and Lubricants . . . . . . 297

MAINTAINING YOUR VEHICLE 257
7
The following checks should be performed at regular
intervals (for example once a week or each time the
vehicle is refueled):
 Windshield washer system/headlamp cleaning
system (optional) – washer system fluid reservoir.
 Air strainer, in vehicles with an air strainer element
maintenance indicator (optional equipment).
 Engine oil level.
 Checking ribbed V-belt.
 Hydraulic brake system, clutch mechanism fluid
level.
 Coolant level.
 Tire and spare wheel condition and pressures of the
same. For more information, refer to "Wheels and
Tires".
 Spare wheel location.
 Vehicle lighting.Windshield Washer System Fluid Reservoir
1. Washer system fluid reservoir
When topping off, add windshield washer fluid ("S"
for summer or "W" for winter) to the water.
Capacity of fluid reservoir (1): about 7.4 US qt (7 liters).

272 MAINTAINING YOUR VEHICLE
Tar Stains
Quickly remove tar stains before they dry and become
more difficult to remove. A tar remover is
recommended.
Paintwork, Painted Body Components
Paint care should be applied when water drops on the
paint surface do not "bead up", normally every 3 to
5 months, depending on climate and washing
detergent used.
Paint cleaner should be applied if paint surface shows
signs of dirt embedding (i.e. loss of gloss).
Do not apply any of these products or wax if your
vehicle is parked in the sun or if the hood is still hot.
Use the appropriate paint stick for quick and
provisional repairs of minor paint damage (i.e., chips
from stones, vehicle doors etc.).
Engine Cleaning
Prior to cleaning the engine compartment, make sure
to protect electrical components and connectors from
the intrusion of water and cleaning agents.Corrosion protection, such as anticorrosion wax
should be applied to the engine compartment after
every engine cleaning. Before applying, all control
linkage bushings and joints should be lubricated. The
poly-V-belt and all pulleys should be protected from
any wax.
Vehicle Washing
Do not use hot water or wash your vehicle in direct
sunlight. Use only a mild car wash detergent.
Thoroughly spray the vehicle with a diffused jet of
water. Direct only a very weak spray towards the
ventilation intake. Use plenty of water and rinse the
sponge and chamois frequently.
Rinse with clear water and thoroughly wipe dry with a
chamois. Do not allow cleaning agents to dry on the
finish.
Due to the width of the vehicle, prior to running the
vehicle through an automatic car wash, fold back the
outside mirrors to prevent them from getting
damaged.
In the winter, thoroughly remove all traces of road salt
as soon as possible.

MAINTAINING YOUR VEHICLE 275
7
Light Alloy Wheels
A wheel care product should be used for regular
cleaning of the light alloy wheels.
If possible, clean wheels once a week, using a soft
bristle brush and a strong spray of water.
Follow instructions on container.
NOTE: Use only acid-free cleaning materials. The acid
could lead to corrosion.
Instrument Cluster
Use a gentle dishwashing detergent or mild detergent
for delicate fabrics as a washing solution. Wipe with a
cloth moistened in lukewarm solution. Do not use
scouring agents.
Steering Wheel and Gear Selector Lever
Wipe with a damp cloth and dry thoroughly or clean
with a leather care product.Cup Holder
Use a gentle dishwashing detergent or mild detergent
for delicate fabrics as a washing solution. Wipe with a
cloth moistened in lukewarm solution. Do not use
scouring agents.
Seat Belts
The webbing must not be treated with chemical
cleaning agents. Use only clear, lukewarm water and
soap. Do not dry the webbing at temperatures above
176°F (+80°C) or in direct sunlight.
Headliner and Shelf Below Rear Window
Clean with soft bristle brush, or use a dry-shampoo
cleaner in case of excessive dirt.
WARNING!
Do not bleach or dye seat belts as this may severe-
ly weaken them. Due to this treatment they may
not be able to provide adequate protection. For ex-
ample, in a crash the belts can be torn.

276 MAINTAINING YOUR VEHICLE
Upholstery
Using aftermarket seat covers or wearing clothing that
have the tendency to give off coloring (e.g. when wet
etc.) may cause the upholstery to become permanently
discolored. By lining the seats with a proper
intermediate cover, contact discoloration will be
prevented.
Leather Upholstery
Wipe leather upholstery with a damp cloth and dry
thoroughly or clean with a leather care product.
Exercise particular care when cleaning perforated
leather as its underside should not become wet.
Cloth Upholstery
Clean with soft bristle brush, or use a dry-shampoo
cleaner in case of excessive dirt.
Tex Upholstery
Pour an interior care product onto soft lint-free cloth
and apply with light pressure.
Hard Plastic Trim Items
Pour an interior care product onto soft lint-free cloth
and apply with light pressure.Plastic and Rubber Parts
Do not use oil or wax on these parts.
Do not use any caustic or alcohol-based or solvent-
based substances to clean plastic surfaces.
Avoid the use of stain removers, iodine tincture, nail
varnish and nail varnish remover, acetone, methylated
spirits, chlorine or ammonium-based cleaning agents,
cleaning agents containing abrasive substances.
ELECTRICAL FUSES
Damaged fuses are recognizable from their burnt-out
filament.
Prior to exchanging a fuse, turn the key in the ignition-
column lock to the 0 position and switch off the
consumer involved.
NOTE: Fuses must not be bridged. Replace fuses with
specified rated current. Only replace fuses when the
cause of the malfunction has been rectified.
NOTE: Fuses and relays (standard equipment) are on
the underside of the ignition column, refer to "Fuses
and Relays Standard Equipment".

280 MAINTAINING YOUR VEHICLE
No. Rated Circuit
1. 10A Parking lamp right, taillamp right
2. 10A High beam head lamp,right
3. 10A High beam head lamp, left,
high beam indicator lamp
4. 10A Backup lamp
5. 10A Brake lamp
6. 20A Windshield wiper motor
7. 15A Horn, heated rear window,
air recirculation switch,
optional equipment relay (terminal 15)
8. 20A Interior lighting, cigarette lighter,
radio (terminal 30)
9. 15A Clock, hazard warning lamps,
parking lamps10. 10A Instrument lighting, license plate lamp
daytime driving lamps
11. 10A Side lamp, left; taillamp, left
12. 10A Low beam headlamp, right
13. 10A Low beam headlamp, left
14. 15A Fog lamp
15. 10A Radio (terminal 15)
16. 25A Engine control unit
17. 15A Engine control unit
18. 15A Ignition (terminal 15)
19. 15A Not in use
20. 15A Heater controls (terminal 30)
21. 30A Heater blower (terminal 30)

284 MAINTAINING YOUR VEHICLE
BULB REPLACEMENT
Switch the lights off to prevent short circuits.
Only touch new bulbs with a clean, lint-free cloth. Do
not touch bulbs with wet or greasy fingers.
Only fit 12 volt bulbs of the same type as before and
with the correct wattage rating.Front Lamp Unit
Bulbs are changed from inside the engine
compartment.
Move the retainer bar to the side and remove the
housing cover.
WARNING!
Bulbs and bulb holders can become very hot. Al-
low the lamp to cool down before changing the
bulb.
Keep bulbs out of reach of children.
Do not use bulbs which have been dropped or
which show signs of scratches on the glass. They
could explode.
Changing an H7 bulb:
The bulb is pressurized. Always wear eye and
hand protection.

MAINTAINING YOUR VEHICLE 293
7
Identification Lamps (Cargo/passenger vans only)
(1) Retaining screw
1. Take out the retaining screw (1) and remove the
lamp housing.
2. To change a bulb, 12V 4CP
Press the bulb into the bulb socket, turn it
counterclockwise and remove.
3. Insert the new bulb.
4. Install the lamp housing.Interior Lighting in Passenger Compartment and
Load Compartment
1. Align a screwdriver on the retaining spring, press it
in and pry the lamp housing out.
2. Replace the bulb, K – 12V 18W
3. Install the lamp housing.

294 MAINTAINING YOUR VEHICLE
Interior Lighting with Reading Lamp
1. Use a screwdriver on the catch spring to press in
and remove the bulb housing.
2. Replace the bulb, K – 12V 10W.
3. Install the lamp housing.Interior Lighting with Interior Sensor Protection
1. Use a screwdriver on the catch spring, remove the
bulb housing.
2. Turn the bulb holder with the bulb in the direction
of the arrow and remove it.
3. Replace the bulb holder and bulb, K – 12V 6W
4. Install the lamp housing.

306 MAINTENANCE SCHEDULESM
A
I
N
T
E
N
A
N
C
E
S
C
H
E
D
U
L
E
S
8
MAINTENANCE - WITH ASSYST MAINTENANCE
COMPUTER
ASSYST provides you with information on the best
possible timing for maintenance work.
When the next maintenance service is due, this will be
indicated in the multi-function display with the
symbol
9 Oil service and fuel filter replacement
9 Maintenance service - displayed in km/miles
or days.
9
If the display shows the number of days, the symbol
È will also appear in the multi-function display.
You should have the maintenance performed within
the stated period/distance.
The service indicator will be reset by your Sprinter
Dealer after an oil service and/or maintenance service
has been performed.REGULAR CHECK-UPS
To maintain the safe operation of your vehicle, it is
recommended that you perform the following tasks on
a regular basis (i.e., weekly or whenever the vehicle is
refueled). Check:
 Engine oil level
 Brake system, clutch mechanism – fluid level
 Battery – acid level
 Windshield washer system and headlamp cleaning
system – fluid level
 Mechanical assemblies (e. g. ,engine, transmission,
etc.) – check for leaks
 Condition of tires and tire pressures
 All exterior lights