FIAT 500 2018 Owner handbook (in English)

129
❒ If the vehicle is equipped with side
skirts, to let the jack pass under the
vehicle, the latter must be tilted (as
shown in 102)
❒ Make sure the jack is correctly
positioned (see fig. 103)
❒ Warn anybody who is nearby that
the car is about to be raised.
They should stay clear and they
should be warned not to touch the
car until it is back on the ground.
100DVDF0S063c
❒ For vehicles with wheel cap: use
the screwdriver provided, applying
leverage to the dedicated opening
on the outer edge.
❒ For cars fitted with alloy wheels:
remove the press-fitted hub cap
using the screwdriver provided.
❒ Loosen the fixing bolts for the
wheel to be changed by about one
turn using the spanner provided.
❒ Partially open the jack using the
handle.
❒ Arrange the jack close to the wheel
to be changed, next to the sign 
fig. 100-101 indicated on the
bodywork.
102DVDF0S0163c
99DVDF0S062c
103DVDF0S065c
101DVDF0S064c

IN AN EMERGENCY
130
❒ Fit the handle to operate the jack
and raise the car until the wheel is a
few centimetres above the ground.
When turning the jack handle, make
sure that it can turn freely without
scraping your hand against the
ground. The moving components of
the jack (screws and joints) can also
cause injuries: avoid touching them.
If you come into contact with
lubricating grease, clean yourself
thoroughly.
❒ Loosen the bolts completely and
remove the wheel to be replaced.
❒ Make sure the contact surfaces
between space-saver wheel and
resting surfaces are clean so that
the fastening bolts will not come
loose.
❒ Fit the space-saver wheel aligning
the pin with one of the holes on the
wheel.
❒ Tighten the 4 fixing bolts, turn the
jack handle to lower the car and
remove the jack.
❒ Fasten the bolts completely,
passing alternately from one bolt to
the opposite one.REFITTING THE WHEEL
32) 40)
Versions with steel wheels
❒ Make sure the contact surfaces
between standard wheel and hub
are clean so that the fastening bolts
will not come loose.
❒ Fit the standard wheel inserting the
4 bolts into the holes, then tighten
them.
❒ Lower the car and remove the jack.
❒ Use the wrench provided to fully
tighten the bolts, passing alternately
from one bolt to the opposite one;
❒ Insert the pressure-fit cup making
the suitable slot coincide with the
inflation valve;
❒ Place the inner part of the hub cap
on the wheel rim;
❒ Engage the hub cap by applying an
axial force in several points as
shown in fig. 104 to allow the
correct coupling between hub cap
and wheel.
Versions with alloy wheels
❒ Place the wheel onto the hub and
tighten the bolts using the wrench
provided.
❒ Lower the car and remove the jack.
❒ Using the spanner provided, fully
tighten the bolts.
❒ Reinsert the press-fitted hub cap,
making sure that the reference hole
on the wheel is aligned with the
reference pin on the cap.
IMPORTANT: if it is not fitted correctly,
the hub cap may detach when the car
is running.
104DVDF0S461c

131
“Fix&Go” KIT
33) 31)
DESCRIPTION
The Fix&Go quick tyre repair kit fig. 105
is located in the luggage compartment,
inside a dedicated container, and
consists of:
❒ one cartridge 1 containing sealant
and fitted with: transparent tube for
injecting the sealant 4 and sticker 3
with the wording “Max 80 km/h” to
be placed in a clearly visible position
(e.g. on the dashboard) after
repairing the tyre;
❒ one compressor 2;
❒ one leaflet containing instructions
for using the kit;
❒ a pair of gloves located in the hose
compartment of the cartridge 4.
REPAIR PROCEDURE
Proceed as follows:
❒ stop the car in a position that is not
dangerous for oncoming traffic
where you can carry out the
procedure safely. The ground must
be flat and sufficiently compact;
❒ stop the engine, engage the hazard
warning lights and the parking
brake;
❒ wear the reflective safety jacket
before getting out of the car (in any
case, comply with the laws in force
in the country you are driving in);
105DVDF0S0230
❒ insert the cartridge 1 containing the
sealant into the dedicated
compartment on the compressor 2
and press it down hard fig. 105.
Remove the adhesive speed label 3
and apply it in a clearly visible
position fig. 106;
❒ wear the gloves;
❒ remove the valve cap from the
punctured tyre and screw the
transparent sealant hose 4 fig. 105
onto the valve. If a 250 ml cartridge
is present the housing of the
transparent tube is provided with
removable ring to facilitate
extraction. Make sure that the
ON-OFF button 5 fig. 107 is in the
off position (button not pressed);
106DVDF0S0234

IN AN EMERGENCY
132
❒ insert the electrical connector
6 fig. 108 into the 12V socket on
the vehicle and start the engine;
❒ turn on the compressor by pressing
the ON-OFF button 5 fig. 107.
When the pressure shown in the
"Wheels" paragraph in the
“Technical data” chapter or on the
specific label appears on the
pressure gauge 7, stop the
compressor by pressing the
ON-OFF button 5 again;
107DVDF0S0232
❒ disconnect the cartridge 1 from the
compressor by pressing the
release button 8 and lifting the
cartridge 1 up fig. 109.
108DVDF0S0231
109DVDF0S0233
If the pressure gauge 7 fig. 107 shows
a pressure less than 1.8 bar / 26 psi
15 minutes after turning on the
compressor, switch off the
compressor, disconnect the sealant
hose 4 from the tyre valve and remove
the cartridge 1 from the compressor
fig. 105.
Move the vehicle about 10m to
distribute the sealant; stop the vehicle
safely, engage the handbrake and
restore the pressure using the black
inflation hose 9 fig. 110 until the
required pressure is reached. If also in
this case, the pressure is lower than
1.8 bar / 26 psi 15 minutes after
turning on, do not resume driving but
contact a Fiat Dealership.
110DVDF0S0235

133
After driving for about 8 km / 5 miles,
position the car in a safe and suitable
area and engage the handbrake.
Take the compressor and restore the
pressure using the black inflation hose
9 fig. 110.
If the pressure shown is higher than
1.8 bar / 26 psi, restore the pressure
and drive safely to a Fiat Dealership as
soon as possible.
If, however, the pressure is lower than
1.8 bar / 26 psi, do not resume driving
but contact a Fiat Dealership.INFLATION PROCEDURE
Proceed as follows:
❒ stop the vehicle safely, as shown
above, and operate the handbrake;
❒ take out the black inflation hose 9
fig. 103 and screw it firmly onto the
tyre valve. Follow the instructions
given in fig. 108 and fig. 110.
Press the air release button
10 fig. 107 to adjust any tyre
overpressure.
CARTRIDGE
REPLACEMENT
Proceed as follows:
❒ only use original Fix&Go cartridges,
which can be purchased from the
Fiat Dealership.
❒ press the release button 8 fig. 109
and lift it to remove the cartridge 1.

IN AN EMERGENCY
134
REPLACING A BULB
34) 19)
GENERAL
INSTRUCTIONS
❒ Before changing a bulb check the
contacts for oxidation;
❒ burnt bulbs must be replaced by
others of the same type and power;
❒ always check the headlight beam
aiming after changing a bulb;
❒ whenever a lamp does not work,
please check that the
corresponding fuse is in tact before
replacing it: please refer to the
paragraph “Replacing fuses” in this
chapter for the location of fuses.
IMPORTANT Whenever the weather is
hot or cold, of after heavy rain, the
surface of the headlights or rear lights
may steam up and/or form droplets of
condensation on the inside. This is a
natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside of
the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from the
centre of the diffuser, extending
progressively towards the edges.

135
TYPES OF BULBS
BulbsTypePower
Main beam headlights H7 55W
Dipped beam headlights H7 55W
Xenon gas discharge dipped beam headlights D1S 35W
Side lights / daytime running lights W21W / LL 5W / 21W
Front direction indicators PY24W / WY21W 21W
Front direction indicators (with xenon gas discharge bulbs) PY24W 24W
Side direction indicators W5W 5W
Rear direction indicators PY21W 21W
Tail lights/brake lights P21 / 5W 10W
Reversing light, rear fog light W16W 21W
Ceiling light C5W 5W
Luggage compartment ceiling light W5W 5W
Number plate C5W 5W
Fog light H3 55W
Additional stop (3rd braking) W5W 5W

IN AN EMERGENCY
136
FRONT LIGHT CLUSTERS
The front light clusters contain side
lights, dipped headlights, main beam
headlights and direction indicator bulbs.
Access to the direction indicator
bulbs (POP versions)
Operating from the engine
compartment, remove the rubber cap
A fig. 111.
Access to the main beam headlight
bulbs (POP versions)
Remove the rubber cap B fig. 111.
111DVDF0S0114c
Access to the direction indicator
bulbs (excluding POP versions)
Operating from the engine
compartment, remove the rubber cap
A fig. 112.
Access to the main beam headlight
bulbs (excluding POP versions)
Operating from the engine
compartment, remove the rubber cap
B fig. 112.
112DVDF0S0196c
Access to the daytime running light
(DRL) and main beam headlight
bulbs
Completely steer the wheels and open
guard door C fig. 113 (on the wheel
arch at the level of the lights) then
remove the rubber cap D.
113DVDF0S0115c

137
MAIN BEAM
HEADLIGHTS
(POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ press the fastener A fig. 114 and
remove the bulb holder;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder locking it
properly;
❒ reinstall the rubber cap.
114DVDF0S0118c
MAIN BEAM
HEADLIGHTS
(Excluding POP
versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ disconnect the central electric
connector A fig. 115 and
and release
the bulb holder catch A;
❒ remove the bulb and replace it;
❒ refit the bulb in its seat and
reconnect the connector;
❒ refit the protection cap in its housing
and turn clockwise.
With gas discharge bulbs (Xenon)
(for versions/markets, where provided)
Contact a Fiat Dealership.
115DVDF0S0197c
MAIN BEAM
HEADLIGHTS
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ release the two bulb holding clips A
fig. 116;
❒ remove the bulb and replace it;
❒ fit the new bulb, making the outline
of the metallic part coincide with the
grooves on the reflector, then hook
back the bulb holding clips;
❒ reinstall the rubber cap.
116DVDF0S0119c

IN AN EMERGENCY
138
SIDE LIGHTS / DAYTIME
RUNNING LIGHTS
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder B fig. 116
anticlockwise and remove it;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder B by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
DIRECTION INDICATORS
Front (POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder A fig. 117
anticlockwise and pull it out;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder A by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
117DVDF0S0116c
Front (Excluding POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder anticlockwise
and remove it;
❒ replace the bulb
bulb holder assembly;
❒ refit the bulb holder in its housing
A fig. 118 by turning it clockwise
and locking it correctly;
❒ refit the protection cap in its housing
and turn anticlockwise.
118DVDF0S0198c