FIAT 500 2018 Owner handbook (in English)

139
Side
IMPORTANT The intervention must be
carried out taking all precautions
necessary to avoid damaging the
bodywork (use a sufficiently rigid and
appropriately thick plastic card).
To replace the bulb, proceed as
follows:
❒ lever the lens off, by initially applying
force from the front towards the
back (1-fig. 119);
❒ lever in the opposite direction, by
applying force from the back
part (2-fig. 119) and remove the
unit;
119DVDF0S0117c
❒ turn the bulb holder anticlockwise,
extract the press-fitted bulb and
replace it;
❒ reinstall the bulb holder into the
lens, then put back the assembly
making sure that the fixing clip has
clicked.
FRONT FOG LIGHTS
(for versions/markets, where provided)
For bulb replacement, contact a Fiat
Dealership.
REAR LIGHT CLUSTERS
To replace the bulb proceed as follows:
❒ open the tailgate;
❒ unscrew the two fastening screws
A fig. 120 and extract the light
cluster axially without rotating it;
❒ remove the bulb holder from its
housing releasing it from the locking
tabs B;
❒ extract the bulbs by pushing them
slightly and turning them counter-
clockwise.The bulbs are arranged as follows in
fig. 121:
C: tail / brake light;
D: direction indicators.
120DVDF0S0199c
121DVDF0S0200c

IN AN EMERGENCY
140
REVERSING LIGHT/REAR
FOG LIGHT
To replace the bulb, proceed as
follows:
❒ From inside the bumper, operate
the tabs A fig. 122 and remove the
press-fit flap;
❒ disconnect the electric connector
A-fig. 123;
❒ turn the bulb holder B fig. 123
anticlockwise and remove the unit;
❒ extract the bulb and replace it;
❒ refit the bulb/bulb holder unit B by
turning it clockwise
122DVDF0S0207c
❒ reconnect the electric connector A;
❒ refit the flap and check that it is
correctly locked.
THIRD BRAKE LIGHTS
To replace the bulb proceed as follows:
❒ remove the two guard caps and
unscrew the two fastening
screws A fig. 124;
❒ remove the assembly;
❒ disconnect the electric connector
B fig. 125;
❒ press the retaining device C and
open the bulb holder;
123DVDF0S0208c
❒ remove the press-fitted bulb to be
replaced and replace it;
❒ close the bulb holder making sure
the retaining device is correctly
locked;
❒ screw in the two fastening screws
and reinstall the guard caps.
124DVDF0S0124c
125DVDF0S0125c

141
NUMBER PLATE LIGHTS
To replace the bulbs, proceed as
follows:
❒ apply pressure to the point shown
by the arrow fig. 126 and remove
the lens;
❒ change the bulb, releasing it from
the side contacts;
❒ fit the new bulb and make sure that
it is correctly clamped between the
contacts;
❒ then refit the lens.
126DVDF0S0126c
REPLACING FUSES
35) 19)
DASHBOARD FUSES
To access the fuses you must remove
the press-fitted cover A-fig. 127.
127DVDF0S067c
The fuse box fig. 128 is located in the
lower area next to the pedal unit.
The 5A fuse for door mirror demisting
is located in the diagnostic socket area
fig. 129.
128DVDF0S068c
129DVDF0S069c

IN AN EMERGENCY
142
FuseAmpereDescription
F13 5 •
Left dipped headlight and headlight alignment control unit power supply
F36 15 Diagnosis socket, radio, climate control, EOBD
F37 5 Brake light switch, instrument panel node
F38 15 Central door locking
F43 15 Windscreen/rear window washer pump
F47 20 Driver’s side power window
F48 20 Passenger’s side power window
F49 5 Parking sensor, control backlighting, electric mirrors
F51 7.5 Climate control, brake lights, clutch, sunroof, electric mirrors
F53 5 Instrument panel node
•
For versions/markets, where provided
ENGINE COMPARTMENT
JUNCTION BOX
The fuse box is located on the right
side of the engine compartment.
To access the fuses, proceed as
follows:
❒ Fully press the screw A fig. 130;
❒ at the same time slowly rotate the
screw anticlockwise, until resistance
is encountered (do not overtighten);
❒ slowly release the screw;
❒ opening is indicated by the entire
screw head coming out of its
housing;
❒ remove cover B, sliding it upwards
on the side guides, as indicated in
the figure.
❒ after replacing the fuse, refit the
cover, making sure that it is closed
properly.
130DVDF0S0201c

143
LPG versions
The LPG system components are
protected by specific fuses.
Contact a Fiat Dealership for
replacement.
The number identifying the electrical
component corresponding to each
fuse is shown on the cover fig. 131.
FuseAmpereDescription
F02 20 Hi-Fi
F08 30 Climate control system fan
F09 30 Headlight washers
F10 10 Horns
F14 15 Main beam headlights
F15 20 Electric sunroof motor
F16 7.5 Dualogic gearbox control unit power supply
(+ignition)
F20 30 Heated rear window
F30 15 Fog lights
F84 10 Dualogic gearbox control unit
F85 20 Front power socket
(with or without cigar lighter)
131DVDF0S0202c

IN AN EMERGENCY
144
IF THE BATTERY IS
FLAT36)
IMPORTANT The battery recharging
procedure is provided for information
purposes only. You are advised to
contact a Fiat Dealership to have this
operation carried out.
IMPORTANT After turning the ignition
key to STOP and having closed the
driver’s side door, wait at least one
minute before disconnecting the battery
and then reconnecting the electrical
supply to the battery.
Charging should be slow at a low
ampere rating for approximately 24
hours. Charging for a longer time may
damage the battery.
Versions without Start&Stop
(for versions/markets, where provided)
To recharge, proceed as follows:
❒ disconnect the terminal from the
negative battery pole;
❒ connect the charger cables to the
battery terminals, making sure that
polarities are correct;
❒ turn on the charger;
❒ when you have finished, turn the
charger off before disconnecting the
battery;
❒ reconnect the terminal to the
negative battery pole.
Versions with Start&Stop
(for versions/markets, where provided)
To recharge, proceed as follows:
❒ disconnect the connector A fig. 132
(pressing the button B) from the
sensor C monitoring the battery
charge status, on the negative pole
D of the battery;
132DVDF0S0127c
❒ connect the positive cable of the
battery charger to the positive
battery pole E fig. 133 and the
negative cable to the terminal of
sensor D;
❒ turn on the charger. At the end of
the charging process, switch the
battery charger off;
❒ after having disconnected the
battery charger, reconnect
connector A to the sensor C as
shown in fig. 132.
133DVDF0S0128c

145
TOWING THE CAR 37)
Version with Dualogic gearbox
Make sure that the gearbox is in neutral
(N) (checking that the vehicle moves
when pushed) and proceed in the
same way as for towing a normal
vehicle with a manual gearbox.
If the gearbox cannot be put in neutral,
do not tow the vehicle and contact a
Fiat Dealership.
ATTACHING THE
TOW RING
The tow ring provided with the car is
housed in the tool box under the boot
mat.
Proceed as follows:
❒ release the front cap
A-fig. 134 or the rear cap fig. 135;
❒ take the tow hook B from its
housing in the tool support;
❒ fully tighten it on the threaded pin.
134 - frontDVDF0S0203c
135 - rearDVDF0S0204c

Blank page

147
SERVICING AND CARE
SCHEDULED SERVICING
Correct servicing is crucial for
guaranteeing a long life for the vehicle
under the best conditions.
For this reason, Fiat has planned a
series of checks and services at fixed
distance intervals and, for
versions/markets, where provided, at
fixed time intervals, as described in the
Scheduled Servicing Plan.
Regardless of the above, it is always
necessary to carefully follow the
instructions in the Scheduled Servicing
Plan (e.g. periodically check level of
liquids, tyre pressure, etc.).
Scheduled Servicing is offered by all
Fiat Dealerships according to fixed
time or kilometres/miles intervals.
If, during each operation, in addition to
the ones scheduled, the need arises
for further replacements or repairs,
these may be carried out with the
owner’s explicit agreement only. If your
vehicle is used frequently for towing,
the interval between one service
operation and the next should be
reduced. IMPORTANT NOTES
Scheduled Servicing interventions are
set out by the Manufacturer. Failure to
have them carried out may invalidate
the warranty.
We advise you to inform a Fiat
Dealership of any small operating
irregularities without waiting for the
next service.

Years4321SERVICING AND CARE
148
5109876
SCHEDULED SERVICING PLAN39) 21)
Thousands of kilometres7515013512010590
PETROL/LPG VERSIONS
IMPORTANT: When you have carried out the last intervention in the table, continue with the scheduled servicing,
maintaining the frequency indicated in the plan by marking each operation with a dot or dedicated note.
Warning: simply restarting maintenance from the beginning of the plan may cause the allowed interval to be exceeded for
some operations!
60453015
Thousands of miles4590817263543627189





 
 
 
 Check tyre condition/wear and adjust pressure, if necessary;
check the condition/expiry date of the “Fix&Go Automatic” repair kit (for versions/markets, where provided)
Check operation of lighting system (headlights, direction indicators,
hazard warning lights, boot, passenger compartment,
glove compartment, instrument panel warning lights, etc.)
Check and, if necessary, top up fluid levels (1)
Check exhaust emissions/smokiness
Use the diagnosis socket to check supply/engine management
systems, emissions and engine oil decay
(for versions/markets, where provided)
Visually inspect the conditions of: bodywork, underbody protection,
pipes and tubes (exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.)
Check windscreen/rear window wiper blade
position/wear (for markets/versions, where provided)
Check operation of windscreen washer system and adjust jets
if necessary
Check cleanliness of bonnet and luggage compartment locks,
cleanliness and lubrication of linkage
(1) Topping up must be carried out with the fluids indicated in this Use and Maintenance Booklet and only after checking that the system is
undamaged