wheel size FIAT BARCHETTA 2003 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2003, Model line: BARCHETTA, Model: FIAT BARCHETTA 2003 1.GPages: 170, PDF Size: 3.55 MB
Page 87 of 170
86
Observe the instructions on this and
the following pages to use the jack and
space-saver spare wheel correctly.
BUMP STARTING IF A TYRE
IS PUNCTURED
General instructions
Do not bump start by
pushing, towing or coast-
ing downhill. This way of
starting could cause a rush of fu-
el into the catalytic exhaust pipe
and damage it beyond repair.
Signal the presence of the
stopped vehicle according
to the laws in force (e.g. hazard
lights, reflecting triangle, etc.).
Any passengers on board should
leave the vehicle, especially if it is
heavily laden. Passengers should
stay away from oncoming traffic
while the wheel is being changed.
If the wheel is being changed on a
steep or badly surfaced road, place
wedges or other suitable material
under the wheels to stop the vehi-
cle.
WARNING
Remember that if the en-
gine is not running, the
brake booster will not work. You
therefore have to use considerably
more effort on the brake pedal.
WARNING
The space-saver spare
wheel is vehicle-specific.
Never use the wheel on other mod-
els. Never use other model spare
wheels on your vehicle.
If you change the type of wheels
(alloy rims instead of steel rims) you
will have to change the entire set of
fastening bolts with another set of
suitably sized bolts.
Only use the spare-saver wheel for
emergencies.
With the spare wheel do not exceed
80 kph.
An orange sticker is attached to the
spare wheel giving the main in-
structions for its use and limitations.
The sticker must never be re-
moved or covered.
Do not fit the hub cap to the
spare wheel.
WARNING
Page 142 of 170
141
WHEELS
RIMS AND TYRES
Pressed steel or alloy wheels (where
applicable), specific bolts (of a differ-
ent size and reciprocally incompatible)
for each of the two types of rim.
Tubeless tyres with radial shell.IMPORTANT Do not use an inner
tube with Tubeless tyres. Do not se-
cure light alloy wheels using bolts de-
signed for steel wheels and vice-versa.
For the compatibility between wheels
and wheel bolts and between these
and the spare wheel, refer to the de-
tailed indications given in the para-
graph “If a tyre is punctured”.
SNOW CHAINS
Do not use snow chains with 195/55
R15 (84V) or 195/45 R16 (80V) tyres
as the chains are likely to interfere
with the plastic wheelarches.
Use only low-profile chains with
185/55 R15 (81H) tyres: maximum
height off the wheel 12 mm. Check the
tautness of the chains after driving
some twenty to thirty yards (twenty
to thirty metres).
Rim Tyre
6 1/2J x15” 195/55 R15 (84V)
6 1/2J x16” 195/45 R16 (80V)
6 J x15” 185/55 R15 (81H)
specific for use
with snow chains
SPARE WHEEL
Pressed-steel rim.
Tubeless tyre.
All homologated tyres are listed in
the Vehicle’s Registration Papers. To
ensure safe driving, make sure that the
tyres are not only of the specified di-
mensions but that all four tyres are of
the same type and make.
Rim Tyre
4.00 Bx14H 135/80 B14
Page 154 of 170
153
ASSEMBLY DIAGRAM
The tow hitch structure fig. 4must
be fixed using 6 M10 bolts at the
points indicated Ø.
All the anchorage points ➀must
have suitable internal 4 mm-thick steel
reinforcements and diam. 20x4.5 mmthick spacers. Dimensions as shown in
the picture and turned up edges.
The underbody plate must be wider
than the plate in the boot. Further-
more, the edge of the plate must be
turned up to avoid sharp corners com-
ing into contact with the body.
fig. 4
P5S00722m
The tow hitch must be anchored to
the body by trimming the grille in the
centre part of the rear bumper.
IMPORTANTA clearly visible
plate of a suitable size and made of
suitable material saying:
MAX LOAD ON BALL COUPLING
35 kg
must be fixed at the height of the ball
coupling (for vehicles with maximum
towable load of 450 kg).Outside rear panel edge
Lower cross member
Laden
Ground level Hook centre of
gravity Centre of the spare
wheel recess floor
Seen from X
Vehicle centreline
Vehicle centreline
Spacer Spare wheel
centre Seen from A
After assembly, all holes
must be adequately sealed
to avoid exhaust fumes from filter-
ing into the vehicle.
WARNING