dashboard warning lights FIAT DUCATO 2011 Owner handbook (in English)

143
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
PROCEDURE FOR
Proceed as follows:
❒engage the handbrake;
❒put the gear lever into neutral;
❒turn the ignition key to MAR-ON: the warning lights
mand Yon the instrument panel will turn on;
❒wait for the warning lights Yand mto turn off.
The hotter the engine is, the quicker this will happen;
❒press the clutch pedal all the way down without
touching the accelerator;
❒turn the ignition key to AVVas soon as the warning
light
mturns off. Waiting too long will waste the
work done by the glow plugs. Release the key as
soon as the engine starts.
If the engine does not start at the first attempt, return
the ignition key to STOP before repeating starting.
STARTING THE ENGINE
The vehicle is fitted with an electronic engine lock
device: if the engine fails to start, see the paragraph
“The Fiat CODE system” in section “Dashboard and
controls”.
STARTING AND DRIVING
It is dangerous to let the engine run in
enclosed spaces. The engine consumes
the oxygen and discharges carbon dioxide,
carbon monoxide and other toxic gases.
WARNING
In the first period of use, we recommend
avoiding excessive stress on the car (for
instance excessive acceleration, extended
travel at maximum speed, sudden braking etc.).
When the engine is switched off never
leave the key into the ignition switch to
prevent useless current absorption from
draining the battery.
Remember that the brake servo and
power steering are not operational until
the engine has been started, therefore much
effort than usual is required on the brake pedal
and steering wheel.
WARNING

163
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
The presence of water in the supply
circuit may cause severe damage to the
injection system and irregular engine
operation. If warning light
clights up (on some
versions with the message on the display),
contact a Fiat Dealership as soon as possible to
have the system bled. If the same message is
displayed immediately after refuelling, water may
have entered the tank: turn the engine off
immediately and contact a Fiat Dealership.
WATER IN DIESEL FILTER (Multijet
versions – amber)
When the key is turned to the MAR-ON
position the warning light comes on but should
go out after a few seconds.
The warning light turns on when there is water in the
diesel fuel filter.
On some versions the display shows the dedicated
message.
c
VEHICLE PROTECTION SYSTEM
FAILURE – FIAT CODE
(amber)
Turning the key to MAR-ON the warning light
will flash only once and then go off.
When the warning light comes on constantly, with key
in MAR-ON, this indicates:
❒a potential fault (refer to “The Fiat CODE system”
paragraph in the section “Dashboard and controls”);
❒a possible theft attempt with an alarm; in this case
the warning light goes off after approximately
10 seconds.
If with the engine running the warning light
Yflashes,
the vehicle is not protected by the engine inhibitor
device (see “Fiat Code system” in section “Dashboard
and controls”).
Contact a Fiat Dealership to have all the keys
reprogrammed.
Y

166
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
WORN BRAKE PADS
(amber)
The warning light on the dial turns on if the
front brake pads are worn; in this case have
them changed as soon as possible.
On certain versions the dedicated message is displayed.
d
Hill Holder failure
The warning light will turn on when the Hill Holder
system is faulty. In this case, contact a Fiat Dealership as
soon as possible.
On certain versions the dedicated message is displayed.
PARKING SENSOR FAILURE (amber)
(for versions/markets, where provided)
The warning light turns on when failure is
detected in the parking sensors.
On some versions warning light
èturns on as an
alternative.
Contact a Fiat Dealership.
On certain versions the dedicated message is displayed.
t
FRONT FOG LIGHTS (green)
The warning light turns on when the front fog
lights are turned on.
5
LEFT-HAND DIRECTION
INDICATOR (green – blinking)
The warning light turns on when the direction
indicator control lever is moved downwards or,
together with the right indicator, when the hazard
warning light button is pressed.
F
DIPPED LOW HEADLAMPS (green)
FOLLOW ME HOME (green)
Dipped beam headlights
The warning light switches on when the dipped beams
are turned on.
Follow me home
The warning light will turn on when this device is active
(see “Follow me home” in section “Dashboard and
controls”).
The display will show a dedicated message.
3

POSSIBLE ICE ON ROAD
This indication starts flashing when the outside
temperature reaches or falls below 3 °C to warn the
driver of the possible presence of ice on the road.
The display will show the dedicated message (only for
versions with a multifunction display).
LIMITED RANGE
The display will show the dedicated message to warn
the driver that the vehicle’s range is less than 50 km.
SPEED LIMIT EXCEEDED
The display shows the dedicated message when the
vehicle exceeds the set speed limit (see “Multifunction
Display” in section “Dashboard and controls”).
SCHEDULED MAINTENANCE
(for versions/markets where provided)
The display shows the dedicated message next to the
scheduled servicing warning and stays on until the deadline
is reached. The warning light goes off after the service has
been carried out at a Fiat Dealership or after 1000 km
have been covered at the service deadline.
DAYLIGHT FAILURE (with reconfigurable
multifunction display)
The display shows the dedicated message along with the
external light fault icon when a daylight failure is found.
168
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
AUTOMATIC TRANSMISSION
FAILURE/MAXIMUM TRANSMISSION
OIL TEMPERATURE
(red)
(for versions/markets where provided)
Turning the ignition key to MAR-ON the warning light
on the dial turns on, but it should go off after a few
seconds.
The warning light on the dial comes on flashing (along
with the display of the message and a buzzer) when
a transmission failure is detected.
The warning light on the dial comes on constantly
(along with the display of the message and a buzzer) to
indicate that the automatic transmission oil
temperature is too high.SELF-LEVELLING SUSPENSION
FAILURE (red)
(for versions/markets where provided)
The warning light comes on when the ignition
key is turned to MAR-ON, but it should switch off after
a few seconds.
The warning light goes on when a fault is present in the
self-levelling suspension system.
Œ
t

172
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0193mfig. 159F0N0194mfig. 160
❒warn anybody nearby that the vehicle is about to be
lifted. They must stay clear and not touch the vehicle
until it is back on the ground. Lift the vehicle.
After lifting the vehicle:
❒for all versions, when gaining access through the
vehicle’s rear right wheel arch, adjust the screw
A-fig. 161 for the spare wheel retaining device, using
the spanner provided with the extension/adaptor B;
❒indicate that the vehicle has broken down using the
devices required by the regulations in the current
country (e.g. warning triangle, hazard lights etc.);
❒take the extension arm and the wrench from the
tool kit under the passenger seat (see
“Compartment under front passenger seat” in the
“Dashboard and Controls” section);
❒for versions with alloy jacks, remove the press-fitted
hub cap;
❒loosen the bolts on the wheel to be replaced by one
turn;
❒turn the wheel to extend the jack partly;
❒arrange the jack near the lift support closest to the
wheel to be replaced at the points shown in fig. 159.
For short wheelbase versions with retractable
footboard, the jack must be positioned at the lift
point shown in fig. 160 aligned (45°) so that it does
not interfere with the retractable footboard;

176
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
E
F0N0825mfig. 170
Automatic FIX&GO QUICK TYRE
REPAIR KIT
(for versions/markets where provided)
The automatic tyre Fix & Go repair kit is positioned at
the front of the vehicle passenger compartment and
includes:
❒cylinder A containing sealer and fitted with:
– a transparent filler pipe B;
– a black pressure restoring pipe E;
– an adhesive label C with the message “max.
80 km/h” to be applied in a position clearly visible
by the driver (on the dashboard) after repairing
the tyre;
❒instruction brochure (see fig. 171), to be used for
prompt and proper use of the quick repair kit and
then to be handed to the personnel charged with
handling the treated tyre;
Each time the spare wheel is moved,
check that it is correctly positioned in its
housing under the floor. If it is not correctly
positioned, this could adversely affect safety.
WARNING
❒introduce the supplied wrench C-fig. 162 with the
suitable extension B-fig. 161 on the screw A-fig. 161
of the spare wheel housing manoeuvring device and
turn clockwise 2 to lift the spare wheel back up until
it is fully supported in its housing beneath the floor
pan, checking that the attachment reference
D-fig. 162 appears in the window on the device.
❒Check the correct position of the replaced wheel
under the floor (the lifting system is supplied with
a clutch to limit the end of the stroke). Incorrect
positioning may jeopardise safety.
❒place the removal spanner back in the tool box;
❒place the tool box in its housing under the passenger
seat.

196
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
If a general protection fuse for safety
systems (air bag system, braking system),
power unit systems (engine system, gearbox
system) or steering system blows, contact a Fiat
Dealership.
WARNING
F0N0095mfig. 205F0N0513mfig. 206
Engine compartment fuse box
To gain access to the fuse box, fig. 208, remove the
protective cover fig. 207.
Right central pillar optional fuse box
(for versions/markets, where provided)
To gain access to the fuse box, fig. 210, remove the
protective cover fig. 209.
ACCESSING THE FUSES
The vehicle fuses are grouped in three control units
located on the dashboard, passenger compartment right
pillar and engine compartment.
Fuse box on the dashboard
To access the dashboard fusebox fig. 206, loosen the
screws A-fig. 205 and remove the cover.

198
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
FUSE SUMMARY TABLE
Dashboard fuse box fig. 205-206
USERSFUSE AMPERE
Right dipped headlamp F12 7.5
Left dipped headlamp F13 7.5
Engine compartment control unit relay, instrument panel control unit relay (+key) F31 5
Lighting of roof lights in the passenger compartment (+battery) F32 7.5
Battery monitoring sensor for Start&Stop versions (+battery) F33 20
Minibus interior lights (emergency) F34 20
Radio, A/C control, alarm, tachograph, F36 10
Battery disconnecting unit, Webasto timer (+battery)
Brake light control (main), third brake light, instrument panel (+key) F37 7.5
Door lock (+battery) F38 20
ABS, ASR, ESP, brake light control (secondary) (+key) F42 5
Windscreen washer (+key) F43 20
Driver's side electric window F47 20
Passenger side electric window F48 20
Parking sensor control unit, radio, controls on the steering wheel, F49 5
centre dashboard, left dashboard, auxiliary dashboard,
battery disconnecting unit (+key)
Airbag (+key) F50 7.5
Climate control system, power steering control unit, reversing lights, F51 5
water in diesel filter sensor, flow meter, tachograph (+key)

203
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0340mfig. 211
RAISING THE VEHICLE
If the vehicle needs to be lifted, go to a Fiat Dealership
which is equipped with arm hoists or workshop lifts.
The vehicle must only be raised laterally by placing the
ends of the arms or workshop lift in the areas shown in
fig. 211.
Do not start the engine whilst the
vehicle is being towed.
WARNING
Before towing, switch off the steering lock
(see „Starting device“ paragraph under the
„Dashboard and controls“ chapter). The brake
servo and power steering will not work while the
vehicle is being towed. More effort on the brake
pedal and steering wheel will therefore be
required. Do not use flexible cables when towing
and avoid jerky movements. During towing
operations, make sure that the fastened joint does
not damage adjoining components. When towing
the vehicle comply with the specific rules of the
Highway Code regarding both the towing device
and the behaviour to maintain on the road.
WARNING
TOWING THE VEHICLE
The vehicle is equipped with two rings for attaching the
tow hook.
The front ring is located in the tool box beneath the
passenger side seat. On versions with Fix&Go kit and
without spare wheel, the tool box is available only on
request for versions/markets where provided. In the
absence of the tool box the vehicle tow hook is housed
in the on-board documentation container, together with
the Owner Handbook.

219
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
If the vehicle must remain unused for
a long time at very low temperatures,
remove the battery and take it to a warm
place to avoid freezing.
USEFUL ADVICE FOR EXTENDING
THE LIFE OF YOUR BATTERY
To avoid draining your battery and make it last longer,
observe the following instructions:
❒when you park the vehicle, ensure that the doors,
tailgate and bonnet are closed properly to avoid the
ceiling lights remain on;
❒the ceiling lights must be off. The vehicle is however
provided with an automatic system for switching off
internal lights;
❒do not keep accessories (e.g. sound system, hazard
warning lights, etc...) switched on for a long time
when the engine is not running;
❒before performing any operation on the electrical
system, disconnect the negative battery cable;
❒battery terminals should always be completely
tightened.
IMPORTANT If the charge level remains under 50% for
a long time, the battery is damaged by sulphation,
reducing its capacity and starting attitude.The battery will also be more at risk of freezing (this can
happen as early as −10°C). Refer to the paragraph
“Vehicle inactivity” in “Starting and driving” if the car is
left parked for a long time.
If, after buying the vehicle, you want to install electric
accessories which require permanent electric supply
(alarm, etc.) contact a Fiat Dealership whose qualified
personnel, in addition to suggesting the most suitable
devices from the Lineaccessori Fiat, will evaluate the
overall electric absorption, checking whether the
vehicle’s electrical system is capable of withstanding the
load required, or whether it should be integrated with
a more powerful battery.
Since these devices continue absorbing energy even
when the ignition key is off, they gradually run down the
battery.
IMPORTANT If a tachograph is fitted, if the vehicle is
parked for a long period of 5 days, it is advisable to
disconnect the negative battery terminal to maintain its
charge.
If the vehicle is equipped with a battery disconnection
function (disconnector), see the description of the
procedure in the „Controls“ paragraph in the
„Dashboard and controls“ section.