bonnet FIAT DUCATO 2012 Owner handbook (in English)
[x] Cancel search | Manufacturer: FIAT, Model Year: 2012, Model line: DUCATO, Model: FIAT DUCATO 2012Pages: 287, PDF Size: 4.5 MB
Page 8 of 287
4
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0002mfig. 2
THE FIAT CODE SYSTEM
This is an electrical engine locking system which
increases protection against attempted theft of the
vehicle. It is automatically activated when the ignition
key is removed.
An electronic device, in fact, is fitted in each ignition key
grip. The device transmits a radio-frequency signal when
the engine is started through a special aerial built into
the ignition switch. The modulated signal, which changes
each time the engine is started, is the “password”, by
means of which the control unit recognises the key and
enables to start the engine.
OPERATION
Each time the vehicle is started by turning the ignition
key to MAR-ON, the Fiat CODE system control unit
sends a recognition code to the engine control unit to
deactivate the immobiliser.
The acknowledgement code is sent only if the Fiat
CODE system control unit has recognised the code
transmitted from the key.
Each time the ignition key is turned to STOP, the Fiat
CODE system deactivates the functions of the engine
management control unit.
If the code is not recognised correctly during ignition,
the
Ywarning light comes on on the instrument panel
together with a specific message on the display (see
“Warning lights and messages”).
SYMBOLS
Special coloured plates have been attached near or on
some of the components of your vehicle. These plates
bear symbols that draw your attention to the
precautions required when handling the component in
question.
The plate summarising the symbols used can be found
under the bonnet, fig. 2.
Page 14 of 287
There is a maximum number of acoustic/visual cycles.
When this is reached the system returns to normal
operation.
IMPORTANT The engine lock function is guaranteed by
the Fiat CODE, which is automatically activated when
the ignition key is extracted from the starter device.
TURNING THE ALARM ON
With the doors and bonnet closed and the ignition key
either turned to STOP or removed, point the key with
the remote control towards the vehicle and press and
release the lock button.
Excluding some markets, the system produces an
acoustic warning (beep) and enables door locking.
The switching on of the alarm is preceded by an self-
diagnosis stage: if a fault is detected, the system
produces another acoustic signal.
In this case, turn the alarm off by pressing the “release
doors/release load compartment” button, check that the
doors and bonnet are properly closed and turn the
alarm back on by pressing the lock button.ELECTRONIC ALARM
(for versions/markets where provided)
The alarm, in addition to all the remote control
functions described previously, is controlled by the
receiver located under the dashboard near the fuse box.
ALARM TRIPPING
The alarm intervenes in the following cases:
❒when one of the doors or bonnet is opened
illegitimately (perimeter protection);
❒when the ignition system is started up (ignition key
rotated to MAR-ON);
❒when the battery cables are cut.
Depending on the market, the activation of the alarm
causes the activation of the siren and the direction
indicators (for about 26 seconds). Alarm tripping and
the number of cycles depend on the sales market.
10
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
Page 15 of 287
11
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
TURNING THE ALARM OFF
Press the door release/load compartment release
button on the key with remote control.
The following operations are performed (excluding
some markets):
❒the direction indicators turn on shortly twice;
❒two short beeps are produced by the warning buzzer;
❒the doors are unlocked.
IMPORTANT If the central door locking system is
released using the metal insert of the key, the alarm is
not disabled. If a door or the bonnet is not properly shut, it will be
excluded from the testing by the alarm system.
If the alarm produces an acoustic signal even when the
doors and bonnet are correctly closed, a fault has
occurred in the operation of the system. Contact a Fiat
Dealership.
IMPORTANT If the central door locking system is
engaged using the metal insert of the key, the alarm is
not enabled.
IMPORTANT The alarm is adapted to meet
requirements in various countries.
Page 108 of 287
104
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0063mfig. 123
BONNET
OPENING
Proceed as follows:
❒open the driver’s door to gain access to the bonnet
release;
❒pull the lever fig. 123 in the direction of the arrow;
❒pull the lever A-fig. 124 as shown in the figure;
❒lift the bonnet and, at the same time, release the
bonnet stay fig. 125 from its locking device D, then
insert the end C-fig. 126 of the stay into the bonnet
housing E.
IMPORTANT Before opening the bonnet, check that
windscreen wiper arms are not lifted from the
windscreen. IMPORTANT With the ignition key in the STOP
position or extracted, the electric windows remain
activated for about 3 minutes and are then deactivated
immediately when one of the doors is opened.
Incorrect use of the electric windows
may be dangerous. Before and during
operation, always check that no-one is exposed
to the risk of being injured either directly by the
moving window or through objects getting
caught and being dragged. When leaving the
vehicle, always remove the key from the ignition
to avoid the risk of injury to anyone remaining
in the car due to accidental operation of the
electric windows.
WARNING
Front passenger side door
A dedicated switch for operating the window is located
on the inner armrest of the passenger side front door.
Page 109 of 287
105
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0323mfig. 124F0N0065mfig. 125
CLOSURE
Proceed as follows:
❒hold the bonnet up with one hand and with the
other remove the rod C-fig. 126 from the housing E
and fit it back into its locking device D-fig. 125;
❒lower the bonnet to approximately 20 centimetres
from the engine compartment, then let it drop. Make
sure that the bonnet is completely closed and not
fastened only by the safety catch. If it is not perfectly
closed, do not try to press the bonnet lid down but
open it and repeat the procedure.
IMPORTANT Always check that the bonnet is closed
properly to avoid it opening while the car is travelling.
The bonnet must always be perfectly
closed while travelling for safety reasons.
Make sure that the bonnet is properly closed
and that the lock is engaged. If you notice
whilst driving that the lock is not perfectly
engaged, stop at once and close the bonnet
properly.
WARNING
Page 110 of 287
106
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0066mfig. 126F0N0138mfig. 127
ROOF RACK/SKI RACK
To fit the roof/ski rack, with provision for versions H1
and H2, use the pins A provided on the edges of the
roof fig. 127.
Long wheelbase vehicles are equipped with 8 pins; short
or medium wheelbase vehicles are equipped with 6 pins;
vehicles with extra-long wheelbases are equipped with
10 pins.
Only carry out these operations with
the vehicle stationary.
WARNING
The incorrect positioning of the bonnet
stay could cause the bonnet to fall
suddenly.
WARNING
Check that the attachment fixing screws
are tight after a few kilometres.
WARNING
Page 210 of 287
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●●
●●
●●●
206
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
SCHEDULED MAINTENANCE PLAN
Thousands of miles 27 54 81 108 135
Thousands of kilometres 48 96 144 192 240
Months 24 48 72 96 120
Check battery charge status and possibly recharge
Check tyre condition/wear and adjust pressure, if necessary
Check operation of lighting system (headlamps, direction indicators,
hazard warning lights, luggage compartment, passenger compartment,
glove compartment, instrument panel warning lights, etc.)
Check operation of windscreen wiper/washer system and adjust jets, if necessary
Check the position/wear of the windscreen/rear window wiper blades
Check cleanliness of bonnet and tailgate locks and cleanliness
and lubrication of linkages
Visually inspect condition of: exterior bodywork, underbody protection,
pipes and hoses (exhaust, fuel system, brakes), rubber elements
(boots, sleeves, bushes, etc.)
Check condition and wear of front disc brake pads and operation
of pad wear indicator
Check condition and wear of rear disc brake pads and operation
of pad wear indicator (for versions/markets where provided)
Check and, if necessary, top-up fluid levels (engine cooling, hydraulic
clutch/brakes, windscreen washer, battery, etc.)
Visual check of accessory drive belt(s) (versions without automatic tensioner)
(130-150-180 Multijet versions)
Check tension of accessory drive belt (versions without automatic tensioner) (▲)
Check tension of accessory drive belt (versions without automatic tensioner)
(115 MultiJet versions) (▲)
(
▲)When the engine oil is changed for the first time, check the tension of the accessories drive belt .
Page 212 of 287
208
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
DEMANDING VEHICLE USE
If the vehicle is mostly used in one of the following
conditions:
❒trailer or caravan towing;
❒dusty roads;
❒short distances (less than 7-8 km) and with external
temperatures below zero;
❒frequently idling engine or long distance low speed
driving or in the case of long term inactivity;
the following checks must be carried out more often
than indicated in the Scheduled Servicing Plan:
❒check front disc brake pad conditions and wear;
❒check cleanliness of bonnet and boot locks and lever
cleanliness and lubrication;
❒visually inspect the conditions of: engine, gearbox,
transmission, pipes and tubes (exhaust – fuel
– brakes), rubber parts (boots, sleeves, bushes, etc.);
❒check battery charge and liquid level (electrolyte);
❒visual check on various drive belt conditions;
❒check and if necessary change engine oil and oil filter.
PERIODIC CHECKS
Before long journeys, check and, if necessary, restore:
❒engine coolant fluid level;
❒brake fluid level;
❒windscreen washer fluid level;
❒tyre pressure and conditions;
❒operation of lights (headlights, direction indicators,
hazard lights, etc.);
❒operation of the windscreen wiper/washer system,
position and wear of the windscreen and rear
window wiper blades.
To ensure that the vehicle is always efficient and well
maintained, it is advisable to make sure that you carry
out the above operations regularly (approximately
every 1000 km and every 3000 km for checking and
topping up engine oil is advisable).
Page 223 of 287
219
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
If the vehicle must remain unused for
a long time at very low temperatures,
remove the battery and take it to a warm
place to avoid freezing.
USEFUL ADVICE FOR EXTENDING
THE LIFE OF YOUR BATTERY
To avoid draining your battery and make it last longer,
observe the following instructions:
❒when you park the vehicle, ensure that the doors,
tailgate and bonnet are closed properly to avoid the
ceiling lights remain on;
❒the ceiling lights must be off. The vehicle is however
provided with an automatic system for switching off
internal lights;
❒do not keep accessories (e.g. sound system, hazard
warning lights, etc...) switched on for a long time
when the engine is not running;
❒before performing any operation on the electrical
system, disconnect the negative battery cable;
❒battery terminals should always be completely
tightened.
IMPORTANT If the charge level remains under 50% for
a long time, the battery is damaged by sulphation,
reducing its capacity and starting attitude.The battery will also be more at risk of freezing (this can
happen as early as −10°C). Refer to the paragraph
“Vehicle inactivity” in “Starting and driving” if the car is
left parked for a long time.
If, after buying the vehicle, you want to install electric
accessories which require permanent electric supply
(alarm, etc.) contact a Fiat Dealership whose qualified
personnel, in addition to suggesting the most suitable
devices from the Lineaccessori Fiat, will evaluate the
overall electric absorption, checking whether the
vehicle’s electrical system is capable of withstanding the
load required, or whether it should be integrated with
a more powerful battery.
Since these devices continue absorbing energy even
when the ignition key is off, they gradually run down the
battery.
IMPORTANT If a tachograph is fitted, if the vehicle is
parked for a long period of 5 days, it is advisable to
disconnect the negative battery terminal to maintain its
charge.
If the vehicle is equipped with a battery disconnection
function (disconnector), see the description of the
procedure in the „Controls“ paragraph in the
„Dashboard and controls“ section.
Page 228 of 287
224
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
❒wipe a sponge with a slightly soapy solution over the
bodywork, frequently rinsing the sponge;
❒rinse well with water and dry with a jet of air or
a chamois leather.
Dry the less visible parts particularly carefully, such as
the door frames, bonnet and the headlight frames,
where water may stagnate more easily. It is a good idea
to leave the vehicle outdoors for a while after washing it
to give the water time to evaporate.
Do not wash the vehicle after it has been left in the sun
or with the bonnet hot: this may alter the shine of the
paintwork.
Exterior plastic parts should be cleaned in the same way
as the rest of the vehicle.
Where possible, do not park the vehicle under trees;
the resinous substances released by many species give
the paint a dull appearance and increase the possibility
of rust.
To protect the paint more effectively, polish
occasionally with special protective waxes; when the
paint tends to cloud because of a build-up of smog,
polish with slightly abrasive protective waxes.
IMPORTANT Bird droppings must be washed off
immediately and carefully as the acid they contain is
particularly aggressive. VEHICLE BODY AND UNDERBODY
WARRANTY
Your vehicle is covered by warranty against perforation
due to rust of any original element of the structure or
body.
For the general terms of this warranty, refer to the
Warranty Booklet.
ADVICE FOR PRESERVING THE BODYWORK
Paint
Paintwork does not only serve an aesthetic purpose, but
also protects the underlying sheet metal. Touch up
abrasions and scratches immediately to prevent rust
formation. Use only original paint products for touch-
ups (see “Bodywork paint identification plate” in the
“Technical specifications” section). Normal maintenance
of paintwork consists in washing the car: the frequency
depends on the conditions and environment where the
car is used. For example, it is advisable to wash the
vehicle more often in areas with high levels of
environmental pollution or on roads spread with salt.
To correctly wash the vehicle proceed as follows:
❒remove the aerial from the roof to prevent damage
to it if the vehicle is washed in an automatic system;
❒wash the body using a low pressure jet of water;