bulb FIAT PANDA 2009 169 / 2.G 4x4 Supplement Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2009, Model line: PANDA, Model: FIAT PANDA 2009 169 / 2.GPages: 26, PDF Size: 0.64 MB
Page 8 of 26
7
FIAT PANDA 4 x 4
IF AN EXTERIOR LIGHT
BURNS OUT
(Fiat Panda 4 x 4 CROSS
version)
IMPORTANT To change an external light
on Fiat Panda 4 x 4 and Fiat Panda 4 x 4
Climbing versions, refer to the Owner
Handbook this Supplement is attached to.
For the type of bulb and power rating re-
fer to paragraph “When needing to change
a bulb” in section “In an emergency” in the
attached Owner Handbook.
FRONT LIGHT UNITS
To change the dipped beam bulb, proceed
as follows:
❒remove the cover A-fig. 12;
❒disconnect the connector C-fig. 13;
❒release the bulb holder catch A;
❒remove the bulb Band fit the new bulb.To change the front sidelight bulb, pro-
ceed as follows:
❒remove the cover A-fig. 12;
❒remove the bulb holder A-fig. 14;
❒remove the bulb B;
❒fit the new bulb.To change the front fog light bulb, proceed
as follows:
❒remove the cover A-fig. 12;
❒disconnect the connector D-fig. 15;
❒turn slightly the bulb holder B and re-
move it;
❒remove the bulb C and fit the new bulb.
To change the main beam bulb, proceed
as follows:
fig. 12F0G0617m
fig. 13F0G0618m
fig. 14F0G0619m
fig. 15F0G0628m
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 7
Page 9 of 26
8
FIAT PANDA 4 x 4
❒loosen the three fastening screws A-
fig. 16and remove the headlight cov-
er;
❒remove the cover by removing the
catches B;
❒remove the lens fig. 17by loosening
the three fastening screws A;
❒turn connector A-fig. 18counter-
clockwise and remove it;
❒remove the bulb B-fig. 18and fit the
new bulb.
To change the direction indicator bulb,
proceed as follows:
❒loosen the two fastening screws A-
fig. 19and remove the cover B;
❒loosen the fastening screws A-fig. 20
and remove the lens B;
❒remove the cap A-fig. 21from the lens
Band remove the bulb holder C;
❒remove bulb Dby pushing it slightly and
turning it counter-clockwise, then fit
the new bulb.
To change side direction indicators, third
brake light and number plate light bulbs re-
fer to paragraph “When needing to change
a bulb” in section “In an emergency” in the
attached Owner Handbook.
fig. 16F0G0620mfig. 18F0G0622m
fig. 17F0G0621mfig. 19F0G0623m
fig. 20F0G0624m
fig. 21F0G0631m
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 8
Page 10 of 26
9
FIAT PANDA 4 x 4
REAR LIGHT UNITS
The bulbs are arranged inside the light unit
as follows fig. 22:
A12V-W5W, double filament bulb for
brake lights/taillights.
B12V-P21W bulb for direction indica-
tors.
C12V-P21W bulb for rear fog light (left
headlight) or reversing light (right head-
light).To change a bulb proceed as follows:
❒loosen the three screws A-fig. 23then
pull gently the headlight outwards un-
til releasing it from the three catches;
fig. 23F0G0625mfig. 24F0G0626m
❒loosen the four screws A-fig. 24and
disconnect the two connectors;
❒remove the required bulb holder turn-
ing it counter-clockwise;
❒remove the required bulb (A, Bor C-
fig. 22), pushing it slightly and turning
it counter-clockwise (bayonet cou-
pling), then fit the new bulb.
fig. 22F0G0627m
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 9