stop start FIAT PANDA 2009 169 / 2.G User Guide

ABS SYSTEM FAILURE (amber)Turning the ignition key to
MAR
the
warning light turns on, but it should go off
after a few seconds.
The warning light will light up when the system is either
not working or not available. Under these circumstances
the braking system will work as normal without the ex-
tra performance offered by the ABS system. Drive care-
fully and contact a Fiat Dealership as soon as possible.
On some versions the display shows the dedicated message.
125KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGESIN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
IMPORTANT Under severe use of the car, it is advisable
to keep the engine on and slightly accelerated for a few
minutes before switching it off.
On some versions the display shows the dedicated message. ENGINE COOLANT HIGH TEMPERA-
TURE (red)
Turning the ignition key to MAR the warning light
turns on, but it should go off after a few seconds. The
warning light turns on when the engine is overheated. If
the warning light comes on when driving, proceed as fol-
lows:
❒in standard normal driving conditions: stop the car,
switch off the engine and check whether the water lev-
el in the reservoir is not below the MIN. mark. In this
case, wait for a few minutes for the engine to cool
down, then slowly and carefully open the cap, top-up
with coolant and check that the level is between the
MIN. and MAX. marks on the reservoir itself. Also
check for any fluid leaks. If, when restarting, the warn-
ing light should come on again, contact a Fiat Dealer-
ship.
❒In case of car heavy duty (e.g.: towing trailer uphill or
fully laden car): decrease speed, if the warning light stays
on, stop the car. Wait for 2 or 3 minutes with the en-
gine running and slightly accelerated to further accel-
erate the coolant circulation. Then stop the engine.
Check the correct liquid level as described above.
ç
LOW BATTERY CHARGE (red)
Turning the ignition key to
MAR
, the warning
light turns on and should go out as soon as the
engine is started (with the engine running at idle speed
a short delay in going out is allowed).
If the warning light stays on contact immediately a Fiat
Dealership.
wx
>
123-134 PANDA EN 7-10-2009 13:49 Pagina 125

126
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CONTINUOUSLY ON: LOW ENGINE
OIL PRESSURE (red)
FLASHING: EXHAUSTED ENGINE OIL
(only Multijet versions with DPF – red)
When the key is turned to MAR the warning light comes
on, but should go out as soon as the engine is started.
Low engine oil pressure
The warning light will turn on constantly together with the
message on the display (for versions/markets where pro-
vided) when the system detects that the engine oil pres-
sure is too low.If the warning light
v
turns on when the
car is travelling (on certain versions to-
gether with the message on the display) stop the
engine immediately and contact a Fiat Dealership.
WARNING
Exhausted engine oil
(Multijet versions with DPF only)
The warning light will turn on flashing together with the
message on the display (for versions/markets where pro-
vided). Depending on the versions, the warning light flash-
ing modes are as follows:
– one minute every two hours;
– cycles of three minutes with intervals with the warning
light off for five seconds until the oil is changed.v
If the warning light comes on, the ex-
hausted engine oil should be changed as
soon as possible, never drive more than 500 km
from the first switching-on of this warning light.
If the above instructions are not complied with,
the engine could be severely damaged and the
warranty may decay. Please note also that the
switching on of this warning light does not depend
on the oil quantity in the engine; when the warn-
ing light flashes, never add oil.
WARNING
After the first indication, at each engine start up the warn-
ing light will continue flashing as above described until the
oil is changed. For those versions/markets where provid-
ed, the display shows a dedicated message together with
the warning light.
The flashing of the warning light should not be consid-
ered as as fault, rather simply informs the customer that
oil needs to be changed after a standard period of car util-
isation.
Remember that the deterioration of the engine oil is ac-
celerated by:
– mainly town use of the car which makes the DPF re-
generation process more frequent;
– use of the car for short journeys, preventing the engine
from reaching operating temperature;
– repeated interruptions to the regeneration process sig-
nalled by the DPF warning light coming on.
123-134 PANDA EN 7-10-2009 13:49 Pagina 126

129KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGESIN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
EOBD ENGINE CONTROL SYSTEM FAILURE
Under standard conditions, when the ignition key is moved
to MAR, the warning light turns on and should go off after
engine start-up. The initial switching-on indicates that the
warning light is working properly. If the warning light ei-
ther stays on or comes on while travelling:
❒switched on steadily: it signals a failure in the supply/
ignition system which could cause high emissions at the
exhaust, possible lack of performance, poor handling
and high consumption levels.
On some versions the display shows the dedicated message.
Under these conditions, you may continue travelling at
moderate speed without demanding excessive effort from
the engine. Prolonged use of the car with the warning light
on may cause damages. Contact a Fiat Dealership as soon
as possible. The warning light goes off if the failure disap-
pears, but it is still stored by the system.
❒flashing: it indicates the possibility of damage to the cat-
alytic converter (see “EOBD system” in section “Know
your vehicle”).
If the warning light flashes, it is necessary to release the ac-
celerator pedal to lower the speed of the engine until the
warning light stops flashing; continue the journey at mod-
erate speed, trying to avoid driving conditions that may
cause further flashing and contact Fiat Dealership as soon
as possible.
If, turning the ignition key to MAR, the
warning light Udoes not turn on or if it
turns on steadily or flashing when travelling
(on certain versions together with the message on
the display), contact a Fiat Dealership as soon as
possible. The operation of the warning light Umay
be checked by the traffic control authorities using
specific devices. Always comply with the traffic
regulations in force in the country where you are
driving.
123-134 PANDA EN 7-10-2009 13:49 Pagina 129

135KNOW
YOUR VEHICLE
SAFETY
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
IN AN EMERGENCY
STARTING THE ENGINEEMERGENCY START-UP
If the Fiat CODE system fails to deactivate engine immo-
bilising system the instrument panel warning lights
Y
and
U
stay on and the engine cannot be started.
To start the engine the emergency start-up can be per-
formed.
Read the whole procedure carefully before trying to car-
ry it out: if you make a mistake, you need to turn the ig-
nition key back to STOP and repeat the whole operation
from the beginning.
Proceed as follows:
❒
read the five-digit electronic code from the CODE card;
❒
turn the ignition key to MAR;
❒
press and hold down the accelerator pedal: the warn-
ing light
U
turns on for about 8 seconds, and then goes
off;
❒
release the accelerator pedal and count the flashes of
the warning light
U
;
❒
count the number of flashes that corresponds to the
first digit of the code on the CODE card, then press the
accelerator pedal and hold it there until the warning
light
U
comes on (for 4 seconds) and then goes off. Re-
lease the accelerator pedal;
CORRECT USE
OF THE CAR
❒
the warning light
U
will start flashing again: after it has
flashed the number of times corresponding to the
second digit on the CODE card, fully depress the ac-
celerator pedal and hold it there;
❒
do the same for the remaining digits on the CODE card;
❒
once the last digit has been entered, hold the acceler-
ator pedal pressed. The warning light
U
will light up for
four seconds and then go out. Release the accelerator
pedal;
JUMP STARTING fig. 120
If the battery is flat, the engine may be started using an aux-
iliary battery with the same capacity or a little higher than
the flat one.
F0Z0694m
fig. 120
135-168 PANDA EN 7-10-2009 14:06 Pagina 135

147KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0673m
fig. 136
F0Z0698m
fig. 137
❒
if after this operation it is still not possible to reach at
least 1.8 bar after five minutes, do not start driving since
the tyre is excessively damaged and the fast tyre re-
pair kit cannot guarantee suitable sealing. Contact
a Fiat Dealership;
❒
if the tyre reaches the pressure specified in “Inflation
pressure” paragraph in the “Technical Specifications”
chapter, start driving immediately;
Apply the adhesive label in a position
clearly visible by the driver as a reminder
that the tyre has been treated with the quick re-
pair kit. Drive carefully, particularly on bends. Do
not exceed 80 km/h. Do not accelerate and brake
suddenly.
WARNING
❒
after driving for about 10 minutes stop and check the
tyre pressure again; remember to engage the handbrake;
If the pressure falls below 1.8 bar, do not
drive any further: the quick tyre repair kit
Fix & Go automatic cannot guarantee proper hold
because the tyre is too much damaged. Contact
a Fiat Dealership.
WARNING
❒
if at least 1.8 bar pressure is read, restore proper pres-
sure (with engine running and handbrake on) and
restart;
❒
drive with the utmost care to the nearest Fiat Dealer-
ship.
135-168 PANDA EN 7-10-2009 14:07 Pagina 147

7,5
–
15
20
20
10
15
15
20
7,5
F19
F20
F21
F22
F23
F24
F30
F84
F85
F87
Engine compartment fuse-box - fig. 169 FUSE AMPEREAir climate control compressorFree fuse Fuel pump supply (Multijet version)Electronic injection primary servicesBraking node valves and ABSElectric power steeringFog lightsDualogic transmission control unitCigar lighter/current socket +15 ABS and stop light control
165KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
20
20
20
30
50
30
30
20
20
20
10/20
30
50
30
T02
T03
T05
T06
T07
T08
T09
T10
T14
T17
T19
T20
T30
T31
Engine compartment unit - fig. 169 RELAYS AMPEREHigh beam relayHorn relayCompressor relayEngine cooling electric fan relay (low speed)Engine cooling electric fan relay (high speed)Air climate control system electric fan relayInjection system main relayFuel pump relay (Multijet version)Fog light relayHeadlight washer relayPump disconnection remote control switch (methane versions)Start-up inhibiting relayDualogic transmission pump relayCigar lighter/current socket relay
135-168 PANDA EN 7-10-2009 14:07 Pagina 165

168KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Before towing, turn the ignition key to
MAR and then to STOP without removing
it. The steering column will automatically lock
when the key is removed and the wheels cannot
be steered.
WARNING
When towing, remember that without the
help of the servo-brake and electric pow-
er steering, a greater effort is required on the ped-
al and steering wheel. Do not use flexible cables
when towing and avoid jerky movements. While
towing, make sure not to damage parts in contact
with the car. When towing the car, comply with
the regulations of the Highway Code about tow-
ing, both concerning the towing device and the
driving behaviour on the road.
WARNING
During towing, never start the engine.
WARNING
135-168 PANDA EN 7-10-2009 14:07 Pagina 168

184KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
❒
to allow even wear between the front and rear tyres,
it is advisable to change them over every 10–15 thou-
sand kilometres, keeping them on the same side of the
car so as not to reverse the direction of rotation. The tyres must be replaced when the tread is less than
1.6 mm thick. In all cases, follow the laws in force in the
country where you are driving.
IMPORTANT NOTES
❒
Avoid braking suddenly, burning starts and violent
knocks against curbs, potholes or other obstacles if pos-
sible. Driving for long stretches over bumpy roads can
damage the tyres;
❒
check the tyres regularly for cuts on the sides, swelling
or irregular tread wear. Contact a Fiat Dealership if re-
quired;
❒
avoid overloading the car when travelling: this may cause
serious damage to the wheels and tyres;
❒
if a tyre is punctured, stop the vehicle immediately
and change it to avoid damage to the tyre, the rim, the
suspensions and the steering system;
❒
a tyre will age even if it is not used much. Cracks in
the tread and on the sidewalls are a sign of ageing. Have
the tyres checked by skilled personnel if they have been
fitted for longer than six years. Remember to check
also the space-saver wheel very carefully;
❒
in case of replacement, always fit new tyres, avoiding
those with an unknown origin;
❒
if a tyre is replaced, also change the inflation valve;
Remember that the road holding qualities
of your car also depend on the correct in-
flation pressure of the tyres.
WARNING
If the pressure is too low the tyre will
get overheated, with the risk of serious
damage.
WARNING
Avoid moving the tyres from the right side
of the car to the left side and vice versa.
WARNING
Never submit alloy rims to repainting
treatments requiring to use temperatures
exceeding 150 °C. The mechanical properties of
the wheels could be impaired.
WARNING
169-190 PANDA EN 7-10-2009 14:15 Pagina 184

215KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONSINDEX
Baby surveillance mirror .......... 43
Battery
– battery recharging ................. 166
– battery replacement ............. 182
– servicing ................................... 181
– starting with auxiliary
battery ..................................... 135
– useful advice for extending
the life of your battery ......... 182
Beam adjustment .......................... 72
Body Computer (trip) ................. 28
Body paintwork identification
plate .............................................. 89
Bodywork marking ...................... 192
Bodywork versions ..................... 193
Bodywork
– advice for preserving
the bodywork ......................... 188
– bodywork version codes ..... 193
Bonnet
– opening/closing ................... 69-70Boot extension ......................... 67-68
Boot ................................................ 65
– boot extension ................... 67-68
– parcel shelf (removal) ........... 67
– parcel shelf lifting ................... 66
– tailgate closing ........................ 66
– tailgate opening ...................... 65
Brake fluid
– level check and top-up ......... 179
– specifications .......................... 205
Brake lights (stop)
– bulb replacement ........... 155-157
Brakes
– technical specifications ......... 196
– handbrake ............................... 113
– brake fluid (type) ................... 179
– fluid level check and top-up .. 179
Bulb replacement ......................... 149
– bulb types ................................ 150
– exterior ................................... 152
– general instructions .............. 149
ABS system .................................. 74
Accessories purchased by
the owner .................................... 86
Additional brake light
– bulb replacement ................... 157
Air bag deactivation ..................... 106
Air filter ......................................... 180
Air recirculation .................. 38-41-45
Air vent and diffusors ................. 37
Annual inspection plan ............... 172
Ashtray ........................................... 55
ASR (system) ................................ 77
ASR function ................................. 77
ASR system ................................... 77
Automatic climate control
system .......................................... 44
– controls ................................... 44
– system servicing ..................... 47
– using the climate control
system ...................................... 47
INDEX
215-224 PANDA EN 13-10-2009 11:48 Pagina 215

218KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONSINDEX
Engine starting .............................. 111
–procedure for petrol
versions ....................................... 111
Engine stopping (Fiat CODE) ... 5
Engine
– engine lock (Fiat CODE) ..... 4
– identification codes ............... 193
– marking .................................... 192
– technical specifications ......... 194
Environment
– emission reduction
devices ......................................... 90
Environmental protection ......... 90
Environmental protection ......... 90
– diesel particulate filter (DPF) 90
EOBD system ............................... 79
ESP system .................................... 76
Exterior lights
(switching on) ............................ 48Fiat CODE system ..................... 5
Fix&Go automatic
(quick tyre repair kit) ............... 143
– wheel replacement ................ 143Flashing
(main beam headlights) ............ 48
Fluids and lubricants
(specifications) ................... 204-205
Fog lights
– bulb replacement ................... 154
– switching on ............................ 54
Follow me home
(headlight device) ...................... 49
“Follow me home” device ......... 49
Front air bags ............................... 104
– deactivation ............................ 106
– driver ........................................ 105
– passenger ................................. 105
Front ceiling light ......................... 52
– bulb replacement ................... 158
Front light units
– bulb arrangement .................. 189
– bulb replacement ................... 152
Front seats .................................... 31
– adjustment ......................... 31-32
– cleaning .................................... 190
– headrests ................................. 33
Fuel cap .......................................... 89Fuel consumption ........................ 206
Fuel cut off switch (system) ...... 54
Fuel cut off switch ....................... 54
Fuel flap .......................................... 89
Fuel gauge ....................................... 15
– fuel type ..................... 87-194-203
Fuel lock system .......................... 54
Fuel reserve .................................. 203
Fuel savings ................................... 115
Fuel supply (specifications) ........ 195
Fuel tank (capacity) ..................... 203
Fuel
– at the filling station ........... 87-88
– consumption ........................... 206
– fuel cut off switch
(system) ................................... 54
– fuel filler cap opening ........... 89
– fuel filler cap ........................... 89
– fuel level gauge and reserve
warning light ........................... 15
– specifications .......................... 203
Fuse boxes (location) .......... 161-162
215-224 PANDA EN 7-10-2009 15:09 Pagina 218