engine system general information FORD FIESTA 2007 Workshop Manual

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-OIA-I31 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01 A-1 31
INSTALLATION
58. Using the special tool, connect the coolant 61. Connect the low-pressure EVAP hose.
hose to the coolant distribution housing.
62. Connect the fuel supply line quick release
59. Using the special tool, connect the coolant coupling.
hose to the coolant distribution housing.
For additional information, refer to: Quick
60. Attach the brake booster vacuum line to
the intake manifold. Release
Coupling (310-00 Fuel System
-
General Information, General Procedures).
63. Connect the fuel return line quick release
coupling.
For additional information, refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
2006.0 Fiesta 1212006 GII 3164en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llS4L
303-01 A-1 33 Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01 A-1 33
INSTALLATION
72. Fill the engine cooling system.
i 1 For additional information, refer to: Cooling
System Draining, Filling and Bleeding -
1.25L Duratec-1 6V (Sigma)ll.3L
Duratec-8V (Rocam)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma)
(303-03A Engine
Cooling - 1.25L
Duratec-1 6V (Sigma)ll.3L Duratec-8V
(Rocam)ll.4L Duratec-1 6V (Sigma)ll .6L
Duratec-1
6V (Sigma), General
Procedures).
2006.0 Fiesta 121zoo6 Gl13164en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-1 45 Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01 A-1 45
INSTALLATION
67. Connect the fuel supply line quick release
70. Tighten the strut and spring assembly top
coupling. mount nuts on both sides.
(: , For additional information, refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
68. Connect the fuel return line quick release
coupling.
For additional information, refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
69. Attach the fuel line and the degas line to
the intake manifold.
Install the cable tie.
71. Connect the powertrain control module
(PCM) electrical connector.
For additional information, refer to:
Powertrain Control Module (PCM)
- 1.25L
Duratec-1 6V (Sigma)llm4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma) (303-14
Electronic Engine Controls, Removal and
Installation).
72, Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll.GL Duratec-1 6V
(Sigma) (303-1 2 Intake Air Distribution
and Filtering, Removal and Installation).
73. Install the front wheels and tires.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires,
Removal and lnstallation).
74. Fill the engine cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
-
1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma)ll.3L DuratecdV (Rocam)
(303-03A, General Procedures).
75. Check the transmission fluid level and top
up with clean automatic transmission fluid
if necessary.
For additional information, refer to:
Transmission Fluid Level Check (307-01
Automatic
Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission
(AW81-40), General
Procedures).
--
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

303-01 B-15 Engine - 2.OL Duratec-HE (M14) 303-01 B-I 5
DIAGNOSIS AND TESTING
I : ,. REFER to Section 303-00 [Engine System -
General Information].
2006.0 Fiesta 1212006 G37449en
procarmanuals.com

303-01 B-69 Engine - 2.OL Duratec-HE (M14) 303-01 B-69
IN-VEHICLE REPAIR
Cylinder Head(21 163 0)
Special Tool(s) 5. Remove the timing chain.
I Materials I
24003
I I Name Specification
Remover/lnstaller, Hose
Clamp
303-397
Removal
For additional information, refer to: Timing
Chain (303-01 Engine
- 2.OL Duratec-HE
(M14), Invehicle Repair).
6. Disconnect the exhaust gas recirculation
(EGR) valve electrical connector.
Hypoid Gear Oil
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable vapors are
always present and may ignite. Failure to
7. Using the special tool, disconnect the
follow these instructions may result in coolant hose
from the EGR valve.
personal injury.
/
SQM-2C9002-AA
( I. Drain the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling
- 2.OL Duratec-HE
(M14), General Procedures).
2. Remove the exhaust manifold support
bracket retaining bolts.
3. Lower the vehicle.
4. Remove the intake manifold.
For additional information, refer to: Intake
Manifold (303-01 Engine
- 2.OL Duratec-HE
(M14), In-vehicle Repair).
8. Using the special tool, disconnect the
coolant hoses from the coolant outlet
connector.
2006.0 Fiesta 1212006 G451308en
procarmanuals.com

303-01 B-71 Engine - 2.OL Duratec-HE (M14) 303-01 B-71
IN-VEHICLE REPAIR
n~emove the camshaft bearing caps in the Install the
cylinder head.
i sequence shown. Tighten the cylinder head bolts in the
' N0TE:Working in several stages, release each sequence
shown in five stages:
camshaft bearing cap retaining bolt two turns at a Stage I : 5 Nm.
time. Stage 2: 15 Nm.
Remove the camshafts.
~CAUTION:K~~~ the valve tappets in
order for installation.
Remove the valve tappets.
( ' 17' &AUTION:R~~~~~ the cylinder head ' bolts in the sequence shown.
Remove the cylinder head.
Discard the gasket.
Discard the bolts.
Installation
Stage3:45Nm.
Stage 4: 90 degrees.
Stage 5: 90 degrees.
3. Install the valve tappets.
4m &AUTION:W~~~~~~ in several stages,
evenly tighten the camshaft bearing cap
bolts in the sequence shown, one half turn
at a time.
Install the camshafts.
Coat the camshaft bearing caps with oil.
Tighten the bolts in the sequence shown in
two stages:
Stage I: 7 Nm.
Stage 2: 16 Nm.
I i
I. Check the cylinder head for distortion. I I
For additional information, refer to: Cylinder 5. N0TE:Only carry out the following step when
Head Distortion
(303-00 Engine System - a new cylinder head or new valves are
General Information, General Procedures). installed.
2. N0TE:lnstall a new cylinder head gasket and
bolts.
2006.0 Fiesta 1212006 G451308en
procarmanuals.com

303-01 B-73 Engine - 2.OL Duratec-HE (M14) 303-01 B-73
IN-VEHICLE REPAIR
12. Install the exhaust manifold upper heat 16.
Install the intake manifold.
shield (engine shown removed for clarity).
For additional information, refer to: Intake
Manifold (303-01 Engine
- 2.OL Duratec-HE
(M14), ln-vehicle Repair).
17. Raise and support the vehicle. For
additional information, refer to: (1 00-02
Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
13. lnstall the generator upper retaining bolt.
18, lnstall the exhaust manifold support bracket
retaining bolts.
19. Fill and bleed the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling
- 2.OL Duratec-HE
14. Install the power steering pump return line
(M14), General Procedures).
support bracket.
15. lnstall the timing chain.
For additional information, refer to: Timing
Chain (303-01 Engine
- 2.OL Duratec-HE
(M14), ln-vehicle Repair).
2006.0 Fiesta 12/2006 G451308en
procarmanuals.com

303-01 B-74 Engine - 2.OL Duratec-HE (M14) 303-01 B-74
REMOVAL
Engine
Special Tool(s)
I I Remover, Power Steering I
I I Removerllnstaller, Hose
General Equipment
I Workshop table I
I Engine hoist I
I Securing straps I
Removal
A WARNING:Do not smoke or carry lighted
tobacco or open flame of any type when
working on or near any fuel related
components. Highly flammable vapors are
always present and may ignite. Failure to
follow these instructions may result in
personal injury.
1. Remove the air cleaner. c.
For additional information, refer to: Air
Cleaner
- 2.OL Duratec-HE (M14) (30312
Intake Air Distribution and Filtering,
Removal and Installation).
2. Remove the battery tray.
For additional information, refer to: Battery
Tray
- 2.OL Duratec-HE (M14) (414-01
Battery, Mounting and Cables, Removal
and Installation).
3. Loosen the strut and spring assembly top
mount nuts by three turns on both sides.
4. Remove the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
5. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
6. Drain the cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling
- 2.OL Duratec-HE
(M14), General Procedures).
7. Detach the exhaust flexible pipe from the
exhaust manifold.
For additional information, refer to: Exhaust
Flexible Pipe
- 2.OL Duratec-HE (M14)
(309-00 Exhaust System, Removal and
Installation).
2006.0 Fiesta 1212006 G451290en
procarmanuals.com

303-01 B-78 Engine - 2.OL Duratec-HE (M14) 303-01 B-78
REMOVAL
Remove and discard the power steering fluid
30. Detach the power steering pump to steering
reservoir O-rings.
gear pressure line from the intake manifold.
28. Using the special tool, remove the power
31. Disconnect the fuel supply line.
steering pump pulley.
For additional information, refer to: Quick
Discard the power steering pump pulley. Release Coupling (310-00 Fuel System - - - - -
General information, General procedures).
,'-
', .
29. Detach the power steering pump to steering
gearpressurelinefromthepowersteering 32. Raiseands~pportthevehicle~For
Pumpm additional information, refer to: (I 00-02
Jacking and Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
33. Remove the air cleaner resonator support
bracket.
2006.0 Fiesta 1212006 G451290en
procarmanuals.com

303-01 B-I 15 Engine - 2.OL Duratec-HE (M14) 303-01 B-115
INSTALLATION
24. Attach the powertrain control module (PCM)
28. Tighten the engine rear mount center
, support bracket to the side member. retaining nut.
25, Install the air cleaner resonator support 29. Tighten the engine front mount retaining
bracket. nuts and retaining bolts.
26. Lower the vehicle.
30. Connect the fuel supply line.
27. Tighten the engine rear mount outer
retaining nuts. For additional information,
refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
2006.0 Fiesta 1212006 ~451291 en
procarmanuals.com