Air conditioning compressor FORD FIESTA 2007 User Guide

303-0514 Accessory Drive . 303-05-4
DESCRIPTION AND OPERATION
Accessory Drive - 2.OL Duratec-HE (M14)
2.OL Duratec HE (M14) engine
,
Item Description
I 1 I Accessory drive belt 1
1 2 1 Power steering pump pulley I
1 3 1 Coolant pump pulley I
1 4 1 Air conditioning (AIC) compressor pulley I
1 5 1 Crankshaft pulley I
1 6 1 Accessory drive belt tensioner pulley I
1 7 1 Generator pulley I
2006.0 Fiesta 1212006 G421383en
8
---
Accessorydrivebeltidlerpulley
procarmanuals.com

303-05-5 Accessory Drive 303-05-5
DIAGNOSIS AND TESTING
Accessory Drive
lnspection and Verification
1. Verify the customer concern.
2.
Visually inspect for obvious signs of mechanical
damage.
Visual lnspection Chart
I Mechanical I
- Damaged or contaminated accessory drive
belt
- Damaged or contaminated pulley(s)
- lncorrect accessory drive belt
- lncorrect fitment of the accessory drive belt
- Accessory drive belt tensioner
- Accessory drive belt idler pulley
- Generator
- Power steering pump
- Power steering pump leakage
- Air conditioning (AIC) compressor
- Pulley(s)
- Loose hardware
3.
If an obvious cause for an observed or reported
concern is found, correct the cause (if
possible)
before proceeding to the next step.
Accessory Drive Belt Concerns
A CAUTI0N:Do not lubricate the accessory
drive belt, accessory drive belt tensioner
or idler
pulley(s) as potential damage to
the accessory drive belt material
construction, accessory drive belt
tensioner damping mechanism, accessory
drive belt tensioner pulley bearing and idler
pulley(s) bearing may occur.
Cracking
Accessory drive belts are made from rubber which
hardens with time and can
develop cracks. As the
belt runs on the back of some of the pulleys, the
cracks are opened up.
Small cracks are not
considered to be a
failure of the belt. Only if the
,crack is deep enough to reach the bottom of the
grooveto expose the cord or any chunks are found
to be missing from the
belt, is the belt condition
considered to be
unacceptable.
1. Check the accessory drive belt for cracks. If the
damage exceeds the
acceptable limit, install a
new accessory drive
belt.
REFER to: Accessory Drive Belt - 1.3L
Duratec-8V (Rocam) (303-05 Accessory Drive,
Removal and Installation).
REFER to: Accessory Drive Belt - 1.4L
Duratec-1 6V (Sigma)/l.GL Duratec-1 6V
(Sigma), Vehicles With: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
REFER to: Power Steering Pump Belt - 1.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V
(Sigma), Vehicles With: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
REFER to: Accessory Drive Belt - I .4L
Duratec-I 6V
(Sigma)/l .6L Duratec-I 6V
(Sigma),
Vehicles Without: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
REFER to: Accessory Drive Belt - 1.4L
Duratorq-TDCi (DV) Diesel (303-05 Accessory
Drive,
Removal and Installation).
REFER to: Accessory Drive Belt - 1.6L
Duratorq-TDCi (DV) Diesel (303-05 Accessory
Drive,
Removal and Installation).
REFER to: Accessory Drive Belt - 2.OL
Duratec-HE (M14) (303-05 Accessory Drive,
Removal and Installation).
Chunking
Chunking describes the condition where long
lengths of rubber become detached from the ribs
of the
belt. This is considered to be a failure of the
belt.
2006.0 Fiesta 1212006 G346263en
procarmanuals.com

303-05-1 8 Accessory Drive 303-05-1 8
REMOVAL AND INSTALLATION
Accessory Drive Belt - 1.4L Duratec-1 6V (Sigma)/l .6L
Duratec-1
6V (Sigma), Vehicles With: Air
Conditioning(21 567 0)
General Equipment 2. Using paint or typing correction fluid, mark
Knife the crankshaft pulley at the 6 o'clock
position.
i
Removal
A CAUTI0N:The accessory drive belt must
not be reused as it is designed to be
stretched onto the pulleys only once.
Failure to follow this instruction may lead
to premature failure of the belt.
I. Raise and support the vehicle. For additional
information, refer to Section
100-02 [Jacking
and Lifting].
2. Detach the power steering line and remove
the crankshaft pulley splash shield.
3. lnstall the installation tool (supplied in the
parts kit) to the crankshaft pulley at the
6
o'clock position. /'
3. Using a suitable knife, cut both accessory
drive belts and remove.
Installation 4. lnstall the accessory drive belt.
1. lnstall the belt around the generator pulley. NOTE: Install a new accessory drive belt and power 2. Install the belt around the air conditioning
steering pump belt. compressor pulley.
I. Wipe clean all of the pulleys to make sure 3. Install the belt around the water pump pulley.
that the accessory drive belt does not slip
during installation.
2006.0 Fiesta 1212006 GI 46274en
procarmanuals.com

303-1 4-6 Electronic Engine Controls 303-1 4-6
DESCRIPTION
AND OPERATION
Item Descri~tion
1 5 1 Crankshaft Position (CKP) sensor 1
Throttle Control Unit (TCU)
1 6 ( Camshaft Position (CMP) sensor I Components
1 7 1 Heated Oxygen Sensor (H02S) I
1 8 1 Power Steering Pressure (PSP) sensor I
1 10 1 Brake Pedal Position (BPP) switch I
9 Vehicle Speed Sensor (VSS)
(only on
vehicles without Anti-lock Braking System
(ABS))
1 12 1 Clutch Pedal Position (CPP) switch I
11
1 13 1 Generator I
Accelerator Pedal Position (APP) sensor
1 14 1 Current supply relay I
1 15 1 Ignition key I -
16
17
1 20 1 Inertia fuel shut-off switch I
Battery
Powertrain Control Module (PCM)
-
18
19
1 21 1 Fuel Pump Driver Module (FPDM) I
Data Link Connector (DLC)
Fuel Pump (FP) relay
1 22 1 Fuel injectors I
23 Evaporative emissions (EVAP) solenoid
1 lvalve
1 24 1 Idle Air Control (IAC) valve 1
1 25 1 Throttle Control Unit (TCU) I
26 Air Conditioning (AIC) compressor clutch
1 I 1 blower switch
1 27 1 Injector Driver
Module (IDM) I
1 28 1 Start inhibit relay I
1 29 1 Instrument cluster I
Item Descri~tion
I I ITP sensor I
1 2 1 Electric motor I
The electronically controlled throttle control unit
(TCU) consists of the following components:
Housing
Throttle flap
Throttle flap spindle
Gear set
Electric motor with pinion
TP sensor
Stop screw
Throttle flap return spring
2006.0 Fiesta 1212006 G204204en
procarmanuals.com