catalytic converter FORD FIESTA 2007 User Guide

Engine - I .25L Duratec-1 6V (Sigma)llI4L
303-01 A-54 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-54
IN-VEHICLE REPAIR
Cylinder Head(21 163 0)
1 I Socket, Cylinder Head Bolts I
Discard the gasket and the nuts. (
Removerllnstaller, Hose
Clamp
303-397 (24-003)
I 24003 1 1 5. Raise and support the vehicle.
Removal
I I 1 For additional information, refer to: Lifting
(100-02 Jacking and Lifting, Description
1. Release the fuel system pressure.
Materials
For
additional information, refer to: Fuel
System Pressure Release (31 0-00 Fuel
System - General Information, General
Procedures). and
Operation).
2. Drain the
cooling system.
For
additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General 7. Remove the exhaust manifold lower heat
Procedures). shield left-hand retaining bolts.
3. Remove the camshaft.
Name
Specification
6. Using a suitable splint or wrap support the
For
additional information, refer to:
Camshafts
(303-01 Engine - 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
In-vehicle Repair).
Engine oil I WSS-M2C912-A1
4. Detach the exhaust flexible pipe from the
catalytic converter. exhaust
flexible pipe.
8. Remove the exhaust manifold lower heat
shield right-hand retaining bolts.
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-63 Duratec-1 6V (Sigma)/l.6L Duratec-1 6V (Sigma) 303-01 A-63
IN-VEHICLE REPAIR
23. Connect the brake booster vacuum line to 27. Install the
exhaust manifold lower heat
the intake manifold. shield
left-hand retaining bolts.
24. Raise and support the vehicle. 28.
N0TE:lnstall a
new flexible pipe gasket and
For
additional information, refer to: Lifting new
nuts.
(1 00-02 Jacking and Lifting, Description Attach the flexible pipe to the catalytic
and Operation). converter
25.
Install the intake manifold retaining bolt.
29. Remove the exhaust flexible pipe support.
26. Position the exhaust
manifold lower heat . 30, Install the camshaft.
shield and install the right-hand retaining
For additional information, refer to:
bolts. Camshafts (303-01 Engine
- 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma),
In-vehicle Repair).
31.
N0TE:lnstall a new oil filter.
Change the engine oil.
32. Fill and bleed the cooling system.
For
additional information, refer to: Cooling
System Draining, Filling and Bleeding
(303-03 Engine Cooling - 1.4L
Duratorq-TDCi (DV) Diesel, General
Procedures).
2006.0 Fiesta 1212006 GI 83740en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-76 Duratec-1 6V (Sigma)lll6L Duratec-1 6V (Sigma) 303-01 A-76
REMOVAL
Support the exhaust flexible pipe with a
suitable support wrap or suitable splint. 43.
Detach the power steering line support
bracket from the engine block.
/' -
40. Detach the exhaust flexible pipe from the
44. Disconnect the power steering line from
catalytic converter. the steering pump.
Discard the nuts and the gasket.
Allow the fluid to drain into a suitable
container.
41. Remove the accessory drive belt.
For additional information, refer to: 45.
Using the special tool, detach the power
Accessory Drive Belt
- I .4L Duratec-16V steering line from the power steering pump.
(Sigma)ll.GL Duratec-1 6V (Sigma), Allow the fluid to drain into a suitable
Vehicles With: Air Conditioning (303-05 container.
Accessory Drive, Removal and
Installation).
42. Detach the
AIC compressor from the
cylinder block and position
it to one side.
2006.0 Fiesta 1212006 GII 31 63en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-89 Duratec-1 6V (Sigma)ll.GL Duratec-1 6V (Sigma) 303-01 A-89
REMOVAL
44m ACAUTION:~~~~ bending of the exhaust Vehicles with air conditioning
I flexible pipe may cause damage resulting 47.
Disconnect the air conditioning (NC)
, in failure. low-pressure cutoff switch electrical
Support the exhaust
flexible pipe with a connector.
suitable support
wrap or suitable splint.
48. Disconnect the NC compressor clutch
45. Detach the exhaust flexible pipe from the electrical connector.
catalytic converter.
Discard the nuts and the gasket.
46. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive
Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles With: Air Conditioning (303-05
Accessory Drive, Removal and
Installation)
I Accessory Drive Belt - I .4L Duratec-I 6V
(Sigma)ll .6L Duratec-1 6V (Sigma),
Vehicles Without: Air Conditioning
(303-05 Accessory Drive,
Removal and
Installation).
49. Disconnect the NC high-pressure cutoff
switch
electrical connector.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 27 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 A-I 27
INSTALLATION
Attach the exhaust flexible pipe to the
33. Attach the gearshift cables to the bracket
catalytic converter.
and turn the abutment sleeves
counterclockwise.
31. Remove the exhaust flexible pipe support.
Vehicles without automated gearshift
32m ACAUTION:H brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
Connect the clutch slave cylinder supply
line.
Install the spring clip.
34. N0TE:Do not install the air cleaner at this
stage.
Adjust the gearshift cable.
For additional information, refer to: Gearshift Cable Adjustment (308-00 Manual
Transmission/Transaxle and Clutch
General Information, General Procedures).
35.
N0TE:Do not install the air cleaner at this
stage.
Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding (308-00 Manual
Transmission/Transaxle and Clutch -
General Information, General Procedures).
Vehicles with automated gearshift
36. Connect the gearshift actuator electrical
connector (colored grey).
2006.0 Fiesta 1212006
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
303-01 A-1 38
INSTALLATION
21. Connect the power steering line to the 25. Connect the ignition switch to starter motor
steering pump.
solenoid and battery to starter motor
solenoid cables.
22. Attach the power steering line support
bracket to the engine block.
26. Connect the crankshaft position (CKP)
sensor electrical connector.
23. N0TE:lnstall new exhaust flange nuts and
a new exhaust flange gasket.
27. Connect the oil pressure switch electrical
Attach the exhaust flexible pipe to the connector.
catalytic converter.
24. Remove the exhaust flexible pipe support.
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-1 I Duratec-HE (M14) 303-04B-11
DIAGNOSIS AND TESTING
Symptom Possible Sources
Action
Fuel injector(s). INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
Fuel rail fuel pressure sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Catalytic converter blocked. REMOVE and visually
INSPECT the catalytic
converter as necessary.
REFER to: Catalytic Converter
- 1.8L Duratec-HE (M14)/2.OL
Duratec-HE (M14) (309-00,
Removal and Installation).
Low cylinder compression. TEST the engine cylinder
compression.
Engine starts but immediately
stops Air cleaner element blocked. INSTALL
a new air cleaner
element.
CKP sensor.
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
CMP sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
PCM. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Low fuel system pressure.
Check the fuel system pres-
sure.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
Fuel system
restriction
I
--
INSPECT the fuel system.
INSTALL new components as
necessary. TEST the system
for normal operation.
I Fuel filter blocked. I INSTALL a new fuel filter. I
Poor idling Air cleaner
element blocked. INSTALL a new air cleaner
element.
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-15 Duratec-HE (M14) 303-04B-15
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
Catalytic converter
blocked. REMOVE and visually
INSPECT the catalytic
converter for damage.
INSTALL a new catalytic
converter as necessary.
REFER to: Catalytic Converter
- 1.8L Duratec-HE (M14)12.OL
Duratec-HE (M14) (309-00,
Removal and Installation).
Black smoke at idle
Air cleaner element blocked.
acceleration INSTALL a new air cleaner
element as necessary.
--
Fuel injectors. INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
ECT sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Fuel rail fuel pressure sensor.
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Catalytic converter blocked.
REMOVE and visually
INSPECT the catalytic
converter for damage.
INSTALL a new catalytic
converter as necessary.
REFER to: Catalytic Converter
- 1.8L Duratec-HE (M14)12.OL
Duratec-HE (M14) (309-00,
Removal and Installation).
I Incorrect valve timing. I CHECK the valve timing. I
2006.0 Fiesta 1212006 GI 65371 en
Air cleaner element blocked. INSTALL a new air cleaner
element as necessary.
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-16 Duratec-HE (M14) 303-04B-16
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
Incorrect or contaminated fuel. CHECK for signs of contamina-).-
tion such as strange odors from, .,,
,
the fuel tank.
If contaminated fuel is found,
DRAIN the complete fuel
system. FLUSH the fuel system
through with clean gasoline.
REFER to: Fuel Tank Draining
(31
0-OOA, General Proced-
ures).
INSTALL a new fuel filter.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
INSTALL a new fuel rail.
REFER to: Fuel
Injection
Supply Manifold (303-04C,
Removal and Installation).
REFER to: Engine Emission
Control (303-08 Engine Emission Control
- 2.OL
Duratec-HE (M14), Diagnosis .
and Testing). I
CKP sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
KS. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
l NSTALL a new set of injectors
as required only after the
checks have been carried out.
Catalytic converter blocked.
Fuel
rail fuel pressure sensor.
REMOVE and visually
INSPECT the catalytic
converter for damage.
INSTALL a new catalytic
converter as necessary.
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
REFER to: Catalytic Converter
I
- 1.8L Duratec-HE (M14)/2.OL
Duratec-H E (M14) (309-00,
Removal and Installation).
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-17 Duratec-HE (M14) 303-04B-17 - --
DIAGNOSIS AND TESTING ~
EGR valve sticking open.
Symptom
Possible Sources Action
REFER to: Engine Emission
Control (303-08 Engine
Emission Control
- 2.OL
Duratec-H E (M14), Diagnosis
and Testing).
Black
smoke at cruising speeds
ECT sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
. Air cleaner element blocked.
Fuel injectors. INSTALL a new air cleaner
element.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
Fuel rail fuel pressure sensor.
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Catalytic converter blocked.
REMOVE and visually
INSPECT the catalytic
converter for damage.
INSTALL a new catalytic
converter as necessary.
REFER to: Catalytic Converter
- 1.8L Duratec-HE (M14)/2.OL
Duratec-HE (M 14) (309-00,
Removal and Installation).
Blue smoke Engine burning oil. CARRY OUT a controlled oil
consumption test over
I000 km
(600 miles). CONFIRM that the
oil consumption is less than 0.1
litre per 1000 km (600 miles).
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com