table FORD FIESTA 2007 Repair Manual

21 1-02-1 5 Power Steering 211-02-15
REMOVAL AND INSTALLATION
Allow the fluid to drain into a suitable Detach the power steering line from the
container. steering gear.
Discard the O-ring seal.
I
Right-hand drive vehicles 6. Disconnect the power steering pressure
(PSP) switch electrical connector. 9. N0TE:Note the position of the power steering
line to aid installation.
Detach the power steering line from the
steering gear.
Left-hand drive vehicles
7. Detach the steering gear return hose from - -
the pressure line. All vehicles
8. N0TE:Note the position of the power steering
line to aid installation.
10. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
2006.0 Fiesta 1212006 G91965en
procarmanuals.com

21 I -02-1 7 Power Steering 211 -02-1 7
REMOVAL AND INSTALLATION
Power Steering Pump to Steering Gear Pressure Line - 1.25L
' . I Duratec-1 6V (Sigma)/l.4L Duratec-1 6V (Sigma)/l .6L
Duratec-1
6V (Sigma), Vehicles Without: Air
Conditioning(l3 440 0)
Special Tool(s)
Expander, Teflon Seal
211-188 (13-015)
( :Removal
Vehicles with manual transaxle
622
Detach the power steering line brackets from
the transaxle.
Socket, Hydraulic Line Union
!:!-269 (I 3-027)
All vehicles
3. Raise and support the vehicle.
For additional information, refer to: Jacking
(100-02 Jacking and Lifting, Description
and Operation)
I. N0TE:Note the position of the power steering I Lifting (100-02 Jacking and Lifting,
line to aid installation. Description
and Operation).
Detach the power steering line bracket from
4m ACAUTION:D~ not disconnect the power
the transaxle. steering
pump pressure adapter from the
power steering pump.
Vehicles with automatic transaxle
2. N0TE:Note the position of the power steering
line to aid installation. Using
the special tool, disconnect the power
steering line from the power steering pump
pressure adapter.
Allow the fluid to drain into a suitable
container.
Discard the O-ring seal.
-- -- -
2006.0 Fiesta 1212006 G397028en
procarmanuals.com

21 1-02-1 8 Power Steering 21 1-02-1 8
REMOVAL AND INSTALLATION
5. N0TE:Note the position of the power steering
line to aid installation.
Detach the power steering line bracket from
the engine block.
I
Detach the power steering line bracket from
the steering gear.
/-.
Right-hand drive vehicles
9. N0TE:Note the position of the power steering
6. Disconnect the power steering pressure line to aid installation.
(PSP) switch electrical connector.
Detach the power steering line bracket from
the steering gear.
Left-hand drive vehicles
7. Detach the steering gear return hose from
the pressure line.
8. N0TE:Note the position of the power steering
line to aid installation.
All vehicles
10. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
2006.0 Fiesta 1212006 G397028en
procarmanuals.com

21 1-02-21 Power Steering 21 1-02-21
REMOVAL AND INSTALLATION
Centralize the steering and lock it in position. Remove and discard the steering column
shaft to steering gear pinion retaining bolt.
6. Detach the steering column shaft from the
steering gear pinion. 7. Remove the accessory drive belt.
For additional information, refer to:
Accessory Drive Belt
- 2.OL Duratec-HE
(M14) (303-05 Accessory Drive, Removal
and Installation).
8. Lower the vehicle.
9. Remove the components in the order
indicated in the following
illustration(s) and
table(s).
2006.0 Fiesta 1212006 G458165en
procarmanuals.com

21 1 -02-30 Power Steering 21 1 -02-30
REMOVAL AND INSTALLATION
Steering Gear to Power Steering Fluid Reservoir Return Line -
2.OL Duratec-HE (M14) RHD (' ,
Centralize the steering and lock it in position. table(s).
Special Tool(s)
2006.0 Fiesta 1212006 G458167en
2. Detach the steering column shaft from the
steering gear pinion.
Discard the steering column shaft to steering
gear pinion retaining bolt.
Pp
205524
24003
Alignment Pins, Subframe
205-524
Removerllnstaller, Hose
Clamp
303-397
General Equipment
Transmission jack 3. Remove the front wheels and tires.
Materials For
additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires, Removal
Name Specification and Installation).
4. Lower the vehicle.
Grease
1. N0TE:Make sure that the road wheels are in 5. Remove the components in the order
the straight ahead position.
indicated in the following illustration(s) and
SA-M 1 C9107-A
procarmanuals.com

21 1 -02-38 Power Steering 21 1 -02-38
REMOVAL AND INSTALLATION
Steering Gear(l3 11 6 0)
I I Separator, Ball Joint Discard
the retaining bolt.

3. Remove the wheels and tires.
I I I For additional information, refer to: Wheel I I I
General Equipment I I
and Tire (204-04 Wheels and Tires, Removal
and Installation).
Removal
All vehicles
Transmission jack 1 4. Disconnect the power steering fluid reservoir
I. N0TE:Make sure that the road wheels are in
the straight ahead position.
Materials
Centralize the steering and lock
it in position. return
hose quick release coupling.
2. Detach the steering column shaft from the
steering gear pinion.
return hose quick release coupling.
Allow the fluid to drain into a suitable
container.
Name Specification 1. Press the power steering fluid reservoir return
5m &AUTION:O~~~ bending of the exhaust
flexible pipe may cause damage resulting in
failure.
2006.0 Fiesta 1212006 GI 05648en
hose quick release coupling locking tangs.
Grease
2. Disconnect the power steering fluid reservoir ( SA-M 1 C9107-A
procarmanuals.com

211 -02-41 Power Steering 21 1-02-41
REMOVAL AND INSTALLATION
15. Detach the power steering lines from the 19. Lower the front axle crossmember to gain
steering gear (left-hand drive shown). access
to the steering gear.
i 20. Remove the steering gear.
16. Disconnect the power steering lines from
the steering gear valve body.
1. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
Discard the O-ring seals.
17.
Using a transmission jack and a wooden
block, support the front axle crossmember.
18. Remove the front axle crossmember
retaining bolts on both sides.
21. Remove and discard the steering gear
bulkhead floor seal.
22. Remove the exhaust heat shield.
2006.0 Fiesta 1212006 GI 05648en
procarmanuals.com

2 1 1 -02-46 Power Steering 211 -02-46
REMOVAL AND INSTALLATION
Steering Gear to Fluid Cooler Return Hose(l3 439 0)
Removal
Left-hand drive vehicles
All vehicles 4. N0TE:Note the position of the steering gear
1. Remove the front right-hand wheel and tire. to
power steering fluid cooler return hose to
aid installation.
For additional information, refer to: Wheel
and Tire
(204-04 Wheels and Tires, Removal Detach
the steering gear to power steering
and Installation). fluid
cooler return hose bracket from the
steering gear.
2. Disconnect the steering gear to power
steering fluid cooler return hose quick
release coupling, from either the power
steering fluid cooler or the power steering
reservoir return hose.
1. Press the power steering fluid cooler hose
quick release coupling locking tangs.
2. Disconnect the power steering fluid cooler
hose quick release coupling.
Allow the fluid to drain into a suitable
container.
3. N0TE:Note the position of the steering gear
to power steering fluid cooler return hose to
aid installation.
Detach the steering gear to power steering
, fluid cooler return hose clips from the
crankshaft pulley splash shield.
5. Detach the steering gear to power steering
fluid cooler return hose clips from the
steering gear.
2006.0 Fiesta IZIZOO~ G91967en
procarmanuals.com

21 1 -02-47 Power Steering 21 1-02-47
REMOVAL AND INSTALLATION
6. Detach the steering gear to power steering All vehicles
fluid cooler return hose from the power
-
/ I steering line.
Right-hand drive vehicles
7. Remove the steering gear heat shield.
9. Disconnect the power steering lines from the
steering gear valve body.
I. Remove the retaining bolt.
2. Rotate the clamp plate.
Allow the fluid to drain into a suitable
container.
Discard the O-ring seals.
10. Remove the steering gear to power steering
fluid cooler return hose.
Installation
1. N0TE:Make sure that the collar on the hose
is fully inserted into the quick release
coupling.
N0TE:Check the power steering lines to steering
gear valve body O-ring seals for damage or fatigue.
8.
N0TE:Note the position of the steering gear Install new O-rin~ seals as necessary. - to power steering fluid cooler return hose to
aid installation. To
install, reverse the removal procedure.
Detach the steering gear to power steering
2. Fill and bleed the power steering system. For
fluid cooler return hose bracket from the additional information, refer
to: (211 -00
steering gear. Steering System
- General
Information)
Power Steering System Filling (General
Procedures),
Power Steering System Bleeding (General
Procedures).
2006.0 Fiesta 1212006 G91967en
procarmanuals.com

21 1-02-48 Power Steering 21 1-02-48
REMOVAL AND INSTALLATION
Power Steering Fluid Cooler(l3 444 0)
Removal 2. Lower the power steering fluid cooler. '-..
I. Raise and support the vehicle. For additional
information, refer to:
(100-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
2. Disconnect the power steering fluid cooler
quick release couplings.
1. Press the power steering fluid cooler hose
quick release coupling locking tangs.
2. Disconnect the power steering fluid cooler
hose quick release coupling.
Allow the fluid to drain into a suitable
container.
3. Remove the radiator splash shield.
4. Lower the vehicle.
5. Remove the power steering fluid cooler.
I. Remove the retaining bolt.
Installation
1. N0TE:Make sure that the collar on the hose
is inserted fully into the quick release
coupling.
To install, reverse the removal procedure.
2. Fill and bleed the power steering system. For
additional information, refer to: (211 -00
Steering System
- General Information)
Power Steering System Filling (General
Procedures),
Power Steering System Bleeding (General
Procedures).
2006.0 Fiesta 1212006 G91972en
procarmanuals.com