cam FORD FIESTA 2007 Repair Manual

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-OIA-1 08 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01A-I 08 --
ASSEMBLY
Special Tool(s)
I Universal Flange Holding
Wrench
205-072 (1 5-030A)
Lifting Bracket, Engine
303-1 22 (2 1 -068A)
21 068A
I 1 Alignment Plate, Camshaft I
21 540
Socket, Cylinder Head Bolt
Gauge,
Bolt Angle
303- 1 74 (2 1 -540)
I I Locking Tool, Flywheel I
Special Tool(s)
Installer, Crankshaft Seal
303-395 (21 -1 71 )
Mounting Stand
303-435 (2 1 -1 87)
Mounting Bracket for 303-435
303-435-06 (21 -031
B)
c
Mounting Plate for
2006.0 Fiesta 1212006 GI 54225en
..
ES21202
Socket, Spark Plug
303-499 (21 -202)
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01A-I13 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-I 13
ASSEMBLY
24n ACAUTION:T~~ thickness of the new 25.
Install the intake manifold lower retaining
, cylinder head gasket must be the same as bolt.
I , that
of the old one (hole marked).
N0TE:lnstall a new cylinder head gasket.
N0TE:Position the cylinder head onto the two
guide sleeves.
Using the special tool, install the cylinder
head.
Tighten the cylinder head bolts in the
sequence shown in three stages.
Stage 1: 15 Nm.
Stage2: 30 Nm.
Stage 3: 90 degrees.
26. Attach the oil level indicator tube to the
intake manifold.
Attach the KS electrical connector to the oil
level indicator tube.
27. Connect the PCV hose to the PCV cover.
28. N0TE:ldentification numbers are provided
on the outer face of the camshaft bearing
caps.
2006.0 Fiesta 1212006 GI 54225en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)lIl4L
303-01 A-I 14 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-1 14
ASSEMBLY
Apply sealant to the points indicated on the
camshaft bearing cap no.
1 and to the mating
surface of the cylinder head.
29. Coat the camshafts and the camshaft
bearing caps with clean engine oil.
30m A~~~~10~:~osition the camshafts in
place so that none of the cams are at full
lift.
N0TE:The camshaft bearing cap numbering starts
at the timing
belt end with El on the exhaust side
and with
I1 on the intake side.
N0TE:The exhaust camshaft has an additional
cam for the camshaft position (CMP) sensor.
Install the camshafts and camshaft bearing
caps.
Tighten the camshaft bearing cap retaining
bolts in the sequence shown in three stages.
Stage 1: One half turn on each bolt until all
of the camshaft bearing caps are in contact
with the
cylinder head.
Stage
2: 7 Nm.
Stage
3: 45 degrees.
31. Coat the camshaft journals and seal lips
with clean engine oil.
32. N0TE:lnstall new camshaft seals. Using the
special tool, install the camshaft
seals.
f:
33. Install the timing belt rear cover.
34. Set the crankshaft to approximately 20
degrees before TDC.
35. Turn the camshafts to top dead center
(TDC) on cylinder number
I and install the
special tool.
36. N0TE:Do not fully tighten the camshaft
timing pulley retaining bolts at this stage.
Make sure the camshaft pulleys turn on the
camshafts.
N0TE:lnstall new camshaft pulley retaining bolts.
2006.0 Fiesta 1u2oos GI 54225en
procarmanuals.com

Engine - 1.25L Dura
303-01A-115 Duratec-1 6V (Sigma)ll.(
tec-16V (Sigma)ll.4L
iL Duratec-1 6V (Sigma) 303-01A-I15
ASSEMBLY
Install the camshaft timing pulleys.
io 37. Install the crankshaft timing belt pulley.
38. N0TE:lnstall a new timing belt.
N0TE:lnstall the timing belt, beginning with the
crankshaft timing pulley working counterclockwise.
Install the timing belt.
39. Remove the blanking plug and install the
special tool.
Carefully turn the crankshaft against the
,I special tool.
40. Measuring the depth of the threaded hole
in the crankshaft.
Depth of the threaded = 42 mm: Use an
MI 2x29 mm crankshaft pulley center bolt. Depth
of the threaded
= 52 mm: Use an
M12x44,5 mm crankshaft pulley center bolt.
41. Install the timing belt lower cover.
42. N0TE:lnstall a new crankshaft pulley
retaining bolt.
Install the crankshaft pulley.
Tighten the crankshaft pulley retaining bolt
in two stages.
Stage 1: 45 Nm.
2006.0 Fiesta 1212006 GI 54225en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 16 Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
303-01 A-1 16
ASSEMBLY
Stage 2: 90 degrees.
Engines with eccentric cam timing belt
tensioner
43. Install the timing belt tensioner.
44. Tension the timing belt.
Tension the timing belt by turning the
tensioner counterclockwise until the arrow
points at the mark and tighten the bolt.
Engines with slotted bracket timing belt
tensioner
45. Install the timing belt tensioner and tension
the timing belt.
Install the bolts finger tight.
Tension the timing belt by turning the
tensioner clockwise until the arrow points in
line with the center of the rectangular hole
(
and tighten the bolts.
Vehicles built 0912003 onwards
46' AWARNING:D~ not remove the special
tool, until the timing belt is correctly
positioned. Failure to follow this instruction
may result in personal injury, or may
damage the timing belt tensioner.
Install the timing belt tensioner.
f,
47. Tension the timing belt.
Remove the special tool.
2006.0 Fiesta 1212006 GI 54225en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-1 17 Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01 A-1 17
ASSEMBLY
Vehicles built 0412005 onwards Using the special tool, tighten the camshaft
! P8' AWARNING:D~ not remove the special
tool, until the timing belt is correctly
positioned. Failure to follow this instruction
may result in personal injury, or may
damage the timing belt tensioner.
Install the timing belt tensioner.
49. Tension the timing belt.
Remove the special tool.
All vehicles
50. CAUTIONS:
nlnstall a hose (order no. E890438S) to
the special tool studs, to prevent damage
to the camshaft pulleys. pulleys.
51. Remove the special tool.
52. Remove the special tool.
ADO not tighten the camshaft pulley bolts
against the timing plate. 53. N0TE:Only turn
the crankshaft in its normal
direction of rotation.
Turn the crankshaft two revolutions.
54. Install the special tool.
2006.0 Fiesta 1212006 GI 54225en
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
303-01 A-1 18 Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-I 18
ASSEMBLY
Carefully turn the crankshaft against the
special tool.
55. Check the valve timing.
If necessary loosen the camshaft pulleys and
correct the camshaft alignment.
56. Remove the special tools.
57. Install the blanking plug.
58. Check the valve clearances, adjust if
necessary.
f:
For additional information, refer to: Valve (.
Clearance Adjustment (303-01 Engine -
1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma), General Procedures).
59. Using the
special tool, install the spark
plugs.
Apply grease to the spark plug threads.
60. N0TE:lnstall the stud bolts to positions 5
and 6.
Install the valve cover. (
Tighten the bolts in the sequence shown in
three stages.
Stage I : Tighten bolt 1 by 3 to 4 turns.
Stage
2: Tighten bolts I through 13 to 3 Nm.
Stage
3: Tighten bolts 1 through 13 to 9 Nm.
'Irn CAUTION: Use a suitable blunt object
to avoid damage to the spark
plug
connector gasket. Coat the inside of the
spark
plug connector with silicone grease
to a depth of 5-10 mm. C
2006.0 Fiesta 1212006 GI 54225en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)llS4L
303-01 A-1 33 Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01 A-1 33
INSTALLATION
72. Fill the engine cooling system.
i 1 For additional information, refer to: Cooling
System Draining, Filling and Bleeding -
1.25L Duratec-1 6V (Sigma)ll.3L
Duratec-8V (Rocam)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma)
(303-03A Engine
Cooling - 1.25L
Duratec-1 6V (Sigma)ll.3L Duratec-8V
(Rocam)ll.4L Duratec-1 6V (Sigma)ll .6L
Duratec-1
6V (Sigma), General
Procedures).
2006.0 Fiesta 121zoo6 Gl13164en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-1 45 Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01 A-1 45
INSTALLATION
67. Connect the fuel supply line quick release
70. Tighten the strut and spring assembly top
coupling. mount nuts on both sides.
(: , For additional information, refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
68. Connect the fuel return line quick release
coupling.
For additional information, refer to: Quick
Release Coupling (310-00 Fuel System
-
General Information, General Procedures).
69. Attach the fuel line and the degas line to
the intake manifold.
Install the cable tie.
71. Connect the powertrain control module
(PCM) electrical connector.
For additional information, refer to:
Powertrain Control Module (PCM)
- 1.25L
Duratec-1 6V (Sigma)llm4L Duratec-1 6V
(Sigma)ll.GL Duratec-1 6V (Sigma) (303-14
Electronic Engine Controls, Removal and
Installation).
72, Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll.GL Duratec-1 6V
(Sigma) (303-1 2 Intake Air Distribution
and Filtering, Removal and Installation).
73. Install the front wheels and tires.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires,
Removal and lnstallation).
74. Fill the engine cooling system.
For additional information, refer to: Cooling
System Draining, Filling and Bleeding
-
1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma)ll.3L DuratecdV (Rocam)
(303-03A, General Procedures).
75. Check the transmission fluid level and top
up with clean automatic transmission fluid
if necessary.
For additional information, refer to:
Transmission Fluid Level Check (307-01
Automatic
Transmission/Transaxle -
Vehicles With: 4-Speed Automatic
Transmission
(AW81-40), General
Procedures).
--
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

303-01 B-I Engine -- 2.OL Duratec-HE (M14) 303-01 B-1
SECTION 303-01 B Engine . 2.OL Duratec-HE (M14)
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
........................................................................\
.............................................. Specifications
Engine Data
........................................................................\
............................................
Engine Oil ........................................................................\
...............................................
........................................................................\
............................................... Oil system
Engine Oil Capacity
........................................................................\
................................
Valve Dimensions ........................................................................\
...................................
Camshaft Dimensions ........................................................................\
.............................
Crankshaft Dimensions ........................................................................\
...........................
Piston Dimensions ........................................................................\
..................................
Cylinder Head ........................................................................\
.........................................
Cylinder Block ........................................................................\
.........................................
PAGE
DESCRIPTION AND OPERATION
Engine ........................................................................\
......................................................... 303-01 8-8
DIAGNOSIS AND TESTING
Engine ........................................................................\
.........................................................
GENERAL PROCEDURES
........................................................................\
....................... Valve Clearance Adjustment
IN-VEHICLE REPAIR
Intake Manifold ........................................................................\
................. (21 183 0)
Crankshaft Front Seal ........................................................................\
............. (21 467 0)
Crankshaft Pulley ........................................................................\
................... (21 5720)
Valve Seals ........................................................................\
....................... (21 238 0)
Valves ........................................................................\
................................. (21 2154)
Camshafts ........................................................................\
.......................... (21 284 0)
Oil Pan ........................................................................\
................................. (21 154 0)
Oil Pump ........................................................................\
.............................. (21 714 0)
Crankshaft Rear Seal ........................................................................\
.......... (21 468 4)
Engine Front Cover ........................................................................\
............. (21 148 0)
Exhaust Manifold ........................................................................\
........................................
Timing Chain ........................................................................\
........................ (21 314 0)
Cylinder Head ........................................................................\
....................... (21 163 0)
REMOVAL
Engine ........................................................................\
.........................................................
DISASSEMBLY
Engine ........................................................................\
................................ (21 134 8)
procarmanuals.com