brake FORD FOCUS 2012 3.G User Guide

MyKeyMessageAction / Description
MYKEY ESC CANNOT BE
DEACTIVATED
—Displays when a MyKeyis
active and trying to disable
ESC. Refer toMyKeyin the
Locks and Securitychapter
for more information.
Park Aid MessageAction / Description
PARKING AID
MALFUNCTION SERVICE
REQUIREDAmberDisplays when the system has
detected a condition that
requires service. Contact your
authorized dealer.
Park Brake MessageAction / Description
PARK BRAKE APPLIED
RedDisplays when the parking
brake is set, the engine is
running and the vehicle is
driven more than 3 mph
(5 km/h). If the warning stays
on after the parking brake is
released.
Power Steering MessageAction / Description
STEERING LOSS STOP
SAFELY
RedThe power steering system is
not working. Stop the vehicle
in a safe place. Contact your
authorized dealer.
STEERING ASSIST FAULT
SERVICE REQUIRED
AmberThe power steering system
required service. Stop the
vehicle in a safe place.
Contact your authorized
dealer.
Instrument Cluster
32
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Power Steering MessageAction / Description
STEERING FAULT
SERVICE NOW
AmberThe power steering system
has detected a condition
within the power steering
system or passive
entry/passive start system that
requires service. Contact your
authorized dealer.
Transmission MessageAction / Description
TRANSMISSION TOO HOT
PRESS BRAKE
AmberDisplays when the
transmission is overheating.
Stop the vehicle in a safe spot
and allow the transmission to
cool and the message
disappears before proceeding.
If the condition persists,
contact your authorized dealer
for service.
Red Displays when the
transmission is overheating.
Stop the vehicle in a safe spot
and allow the transmission to
cool and the message
disappears before proceeding.
If the condition persists,
contact your authorized dealer
for service. If the vehicle is
driven with this message
active you may experience
vehicle shudder as a further
overheat warning.
Instrument Cluster
33
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Transmission MessageAction / Description
TRANSMISSION
OVERHEATING STOP
SAFELY
RedDisplays when the
transmission is overheating.
Stop the vehicle in a safe spot
and allow the transmission to
cool before proceeding. If the
condition persists, contact
your authorized dealer for
service.
TRANSMISSION NOT IN
PARK SELECT P—Displays as a reminder to shift
into park.
TRANSMISSION
MALFUNCTION SERVICE
NOWRedDisplays when the
transmission requires service
due to a malfunction. Contact
your authorized dealer.
USE BRAKE STOP SAFELY
RedDisplays when the vehicle
needs to be brought to a safe
stop to allow the transmission
to cool.
TRANSMISSION HOT
STOP OR SPEED UP
—Displays when the
transmission is overheating
when idling with the brake
applied for long periods such
as in heavy stop-and-go
traffic. Stop the vehicle in a
safe spot and allow the
transmission to cool before
proceeding or drive an
alternate route that allows less
idling/slower speeds.
Instrument Cluster
34
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Transmission MessageAction / Description
TRANSMISSION HOT
WAIT X MINUTE
—Displays when the
transmission is overheating.
Stop the vehicle in a safe spot
and allow the transmission to
cool for the displayed time
before proceeding.
TRANSMISSION HOT
WAIT...
—Displays when the
transmission is overheating.
Stop the vehicle in a safe spot
and allow the transmission to
cool before proceeding.
TRANSMISSION READY
—Displays after an transmission
overheating event and the
transmission has cooled
enough to allow proper
transmission function.
TRANSMISSION LIMITED
FUNCTIONAmberDisplays when certain
transmission features are
disabled.
TRANSMISSION
WARMING UP PLEASE
WAIT—Displays when the
transmission needs a warming
period before it will operate
properly.
PRESS BRAKE PEDAL
—Displays to request the
operator to apply the brake as
needed by the transmission.
TO START PRESS BRAKE
—Displays when starting the
vehicle as a reminder to apply
the brake.
Instrument Cluster
35
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

•A connectedBluetoothenabled cellular phone that has adequate
network coverage, battery power and signal strength.
•The vehicle is located in the U.S. or Canada or in a territory in which
911 is the emergency number.
WARNING:Unless 911 Assist™ is previously configured to ON
prior to a crash, 911 Assist™ will not dial for help during an
emergency, which could delay response time, increasing the risk of
serious injury or death after a crash.
The 911 Assist™ feature is initially set to OFF. To access the setting:
1. Press
or PHONE to enter thePhone Menu.
2. Scroll repeatedly until911 Assistappears in the radio display.
3. Press OK to confirm and enter the911 Assistmenu.
4. Scroll to select between On and Off selections.
5. Press OK when the desired option appears in the radio display. Set On
or Set Off will appear in the display as confirmation.
Note:Off selections include: Off with reminder and Off without
reminder. Off with reminder provides a display and voice reminder at
phone connection at vehicle start. Off without reminder provides a
display reminder only without a voice reminder.
For more information, please visit www.SyncMyRide.com or
www.syncmaroute.ca.
Note: Before enabling (setting to ON), review the 911 Assist™
Privacy Notice.
Vehicle health report (if equipped, U.S. only)
WARNING:Always follow scheduled maintenance instructions,
regularly inspect your vehicle, and seek repair for any damage or
problem you suspect. Vehicle Health Reports supplements, but cannot
replace normal maintenance and vehicle inspection. Vehicle Health
Report only monitors certain systems that are electronically monitored
by the vehicle and will not monitor or report the status of any other
system, (i.e., brake lining wear). Failure to perform scheduled
maintenance and regularly inspect your vehicle may result in vehicle
damage and serious injury.
Note: Your Vehicle Health Report feature requires activation
prior to use. Visit www.SyncMyRide.com to register.There is no fee
or subscription associated with Vehicle Health Report, but youmust
register to use this feature.
Entertainment Systems
86
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Take your vehicle to a dealer for service if any of the above conditions of
unacceptable moisture are present.
Using the right bulbs
Replacement bulbs are specified in the chart below. Headlamp bulbs
must be marked with an authorized “D.O.T.” for North America to ensure
lamp performance, light brightness and pattern and safe visibility. The
correct bulbs will not damage the lamp assembly or void the lamp
assembly warranty and will provide quality bulb burn time.
Function Trade number
Headlamps high beam H1
Headlamp low beam H11LL
Turn lamp (front) W21W
Park/Side marker lamp (front) 168NA
Fog lamps (if equipped) H11 LL
Stop/tail lamp 3157K
Turn lamp 3757AK
Backup lamp 921
*License plate lamp LED
* High-mount brake lamp LED
* To replace these lamps - see your authorized dealer.
To replace all instrument panel lights - see your authorized dealer
Replacing interior bulbs
Check the operation of all bulbs frequently.
Replacing exterior bulbs
Check the operation of all the bulbs frequently.
Lights
129
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Replacing tail/brake and turn signal bulbs
1. Make sure the headlamp control
is in the off position and open the
trunk.
2. Remove the plastic cover from
inside the luggage compartment.
3. Remove the two nuts from the
lamp assembly
4. Gently pull the lamp assembly
away from the vehicle
5. Remove the turn signal bulb (1)
or the tail/brake bulb (2) by turning
the bulb socket counterclockwise.
Gently pull the bulb straight out of
the socket.
Install the new bulb in reverse
order.
Replacing fog lamp bulbs (if equipped)
1. Make sure the headlamp switch is
in the off position.
2. Reach under the front fender and
remove the aeroshield. Then remove
the harness/bulb assembly from the
fog lamp by turning it
counterclockwise.
3. Disconnect the harness from the
bulb by pulling it straight out.
Install the new bulb in reverse order.
1
2
Lights
132
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

Replacing license plate lamp assembly
Your vehicle is equipped with an LED license plate lamp assembly. It is
designed to last the life of the vehicle. If replacement is required, it is
recommended that you see your authorized dealer.
Replacing high-mount brake lamp assembly
Your vehicle is equipped with an LED center high-mount stop lamp. It is
designed to last the life of the vehicle. If replacement is required, it is
recommended that you see your authorized dealer.
Lights
133
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

3. Press and release SET+.
4. Take your foot off the accelerator pedal.
5. The indicator
light on the instrument cluster will turn on.
Note:
•Vehicle speed may vary momentarily when driving up and down a
steep hill.
•If the vehicle speed increases above the set speed on a downhill, you
may want to apply the brakes to reduce the speed.
•If the vehicle speed decreases more than 10 mph (16 km/h) below
your set speed on an uphill, your speed control will disengage.
Disengaging speed control
Pull CAN toward you and release, tap the brake pedal or press the clutch
pedal (if equipped). Disengaging the speed control will not erase
previous set speed.
Note:When you use the clutch pedal to disengage the speed control,
the engine speed may briefly increase; this is normal.
Resuming a set speed
Pull RES toward you and release. This will automatically return the
vehicle to the previously set speed.
Increasing speed while using speed control
To set a higher speed:
•Press and hold SET+ until you get to the desired speed, then release.
You can also use SET+ to operate the tap-up function. Press and
release SET+ to increase the vehicle set speed in 1 mph (1.6 km/h)
increments.
•Use the accelerator pedal to get to the desired speed, then press and
release SET+.
Reducing speed while using speed control
To reduce a set speed:
•Press and hold SET– until you get to the desired speed, then release.
You can also us SET– to operate the tap-down function. Press and
release SET– to decrease the vehicle set speed in 1 mph (1.6 km/h)
increments.
•Press the brake pedal until the desired vehicle speed is reached, then
press and release SET+.
Driver Controls
142
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)

POSITIVE RETENTION FLOOR MAT
WARNING:Do not install additional floor mats on top of the
factory installed floor mats as they may interfere with the
accelerator or the brake pedals.
Position the floor mat so that the
eyelets are over the retention posts
and press down to lock in. Make
sure that the mat does not interfere
with the operation of the accelerator
or the brake pedal. To remove the
floor mat, reverse the installation
procedure.
Driver Controls
150
2012 Focus(foc)
Owners Guide, 1st Printing
USA(fus)