Torque FORD KUGA 2011 1.G Owner's Manual

Audio Unit Antenna — Vehicles Without: Glass Roof Panel
Removal
NOTE:
Removal steps in this procedure may
contain installation details.
1. 2.
Torque: 3 Nm
Installation
1.
To install, reverse the removal procedure. G1158244en
2008.50 Kuga 8/2011 415-01-22
Information and Entertainment System
415-01-22
REMOVAL AND INSTALLATIONTO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUALE104243 E113336

5.
Torque: 3 Nm 6.
Attach a suitable draw cord to the antenna
cable.
General Equipment: Draw Cord
3. Installation
1.
To install, reverse the removal procedure. G1158246en
2008.50 Kuga 8/2011 415-01-31
Information and Entertainment System
415-01-31
REMOVAL AND INSTALLATIONTO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUALE113254 1223E113264

50.
Torque: 12 Nm
51.
G1065595en
2008.50 Kuga 8/2011 418-02-17
Wiring Harnesses
418-02-17
REMOVAL AND INSTALLATIONTO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUALE114537

Engine Compartment Wiring Harness
Removal
NOTE:
Removal steps in this procedure may
contain installation details.
1. 2.
Refer to: Headlamp Assembly (417-01 Exterior
Lighting, Removal and Installation).
3. Refer to: Wheel and Tire (204-04 Wheels and
Tires, Removal and Installation).
4. Refer to: Fender Splash Shield (501-02 Front
End Body Panels, Removal and Installation).
5. Refer to: Front Bumper Cover (501-19 Bumpers,
Removal and Installation).
6. Torque: 10 Nm
7.
Torque: 10 Nm
G1065599en
2008.50 Kuga 8/2011 418-02-37
Wiring Harnesses
418-02-37
REMOVAL AND INSTALLATIONTO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUALE102365

28.TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL 29.
Torque: 10 Nm
Installation
1.
To install, reverse the removal procedure . G1065599en
2008.50 Kuga 8/2011 418-02-43
Wiring Harnesses
418-02-43
REMOVAL AND INSTALLATION

Description
Item
HS CAN
1
DLC2
MS CAN
3
Instrument cluster (gateway)
4
Front windshield wiper motors
5
GEM6
Rear window wiper motors
7
Indicator/heated windshield
8
Indicator/heated rear window
9 Description
Item
Mini-liftgate latch motor
10
Liftgate latch motor
11
Electric booster Heater
12
Front wiper windscreen washer pump
13
Rear wiper windscreen washer pump
14
Headlamp
15
Courtesy Lighting
16
Alarm horn
17
System Operation
GEM.
The following functions are controlled or performed
by the GEM at a battery voltage of between 9 and
16 volts:
• Current distribution
• Battery charging (Smart Charge)
• Ignition overload protection
• Headlamp switch-off delay
• Turn signals
• Interior lighting
• Heated windscreen
• Heated rear window and heated external mirrors
• Ambient air temperature
• Brake fluid level
• Automatic headlamps
• Combined rain sensor/light sensor
• Windshield wash/wipe system
• Speed control – reads the speed control switches andtransmits signals on the CAN data bus
• central door locking – transmits signals on the CAN data bus
• Anti-theft
• Electric booster Heater
• Climate control
• Parking brake –(monitors the switch and transmits the signal
on the CAN data bus
• Communication via the medium-speed CAN data bus Component Description
Battery charging (Smart Charge)
In addition to the familiar functions, the Smart
Charge system also performs the following
functions:
•
Automatic deactivation of non-critical high power
electrical consumers when the battery voltage
is low in order to reduce the level of current
drawn.
• Automatic activation of non-critical high power electrical consumers when the battery voltage
is excessively high in order to protect
components which are sensitive to increased
voltages.
The battery charging current is optimized through
continuous calculation of the battery temperature
and monitoring of the alternator output voltage.
The alternator load is signaled to the PCM
(powertrain control module) in order to provide it
with an early indication when an electric component
is to be switched on or off, thereby also providing
information about imminent changes to the amount
of torque demanded by the alternator. By
evaluating this information the PCM is capable of
increasing the stability of the engine under idling.
The two remaining functions of the Smart Charge
system are controlled by the GEM. G1030788en
2008.50 Kuga 8/2011 419-10-6
Multifunction Electronic Modules
419-10-6
DESCRIPTION AND OPERATIONTO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Front Toe Adjustment(14 117 3)
General EquipmentWheel Alignment System
NOTE: Make sure that the vehicle is standing on
a level surface.
1. CAUTION: Make sure that the steering wheel lock is engaged.
NOTE: Make sure that the road wheels are in
the straight ahead position.
E99259
2. Check the toe setting on both sides.
General Equipment: Wheel Alignment System
3. Loosen on both sides.
Torque: 69
Nm
1.
2.NOTE: Make sure that the boot is correctly
located.
Rotate the tie-rods an equal amount in either
a clockwise or a counterclockwise direction
to adjust the toe setting on both sides.
2
E67410
1
2
G1000721en2008.50 Kuga8/2011
204-00- 15
Suspension System - General Information
204-00- 15
GENERAL PROCEDURES
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Rear Toe Adjustment(15 211 3)
General EquipmentWheel Alignment System
NOTE: Make sure that the vehicle is standing on
a level surface.
1. Check the toe setting.
Refer to: Specifications (204-02 Rear
Suspension, Specifications).
General Equipment: Wheel Alignment System
2. Refer to: Lifting(100-02 Jacking and Lifting,
Description and Operation).
3. Loosen the rear lower arm adjustment cam nut
on both sides.
Torque: 18
Nm
E69309
4.Lower the vehicle.
5. Bounce the vehicle to make sure that the
suspension is in its normal resting position.
6. Adjust the toe setting.
E69678
7. NOTE: Only tighten the nuts and bolts when the
suspension is in the normal drive position.
Torque: 90
Nm
E69309
G1000722en2008.50 Kuga8/2011
204-00- 16
Suspension System - General Information
204-00- 16
GENERAL PROCEDURES
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

Lower Arm(14 706 0; 14 707 0; 14 709 0)
Special Tool(s)204-605
Separator, Lower Arm Ball
Joint
E63772
204-609
Protection Cap, Ball Joint
Gaiter
E75372
Removal
NOTE:Removal steps in this procedure may
contain installation details.
1. Refer to: Wheel and Tire (204-04 Wheels and
Tires, Removal and Installation).
2.
E98543
x7
3. Torque: 83Nm
E97635
4.If equipped.
Torque: 8
Nm
E75215
5.Special Tool(s): 204-605
E97732
204-605
G1000207en2008.50 Kuga8/2011
204-01- 13
Front Suspension
204-01- 13
REMOVAL AND INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL

6.Special Tool(s): 204-609
E81908
204-609
7. CAUTION: Make sure that new bolts are
installed.
1. Torque:• Stage 1: 100
Nm
• Stage 2: Loosen 90°
• Stage 3: 125Nm
2. Torque: 175Nm
E97634
1
1
2
Installation
1.To install, reverse the removal procedure.
2. Check the toe setting and adjust as necessary.
Refer to: Front Toe Adjustment (204-00
Suspension System - General Information,
General Procedures).
G1000207en2008.50 Kuga8/2011
204-01- 14
Front Suspension
204-01- 14
REMOVAL AND INSTALLATION
TO MODEL INDEX
BACK TO CHAPTER INDEX
FORD KUGA 2011.0MY WORKSHOP REPAIR MANUAL