battery location FORD MUSTANG 1969 Volume One Chassis

03-05-07

Steering Columns And Linkage
03-05-07

the steering column
(F in Fig. 8).

7.
Disconnect
the
transmission shift

rod
at the
shift tube.

8. Working under
the
hood, install

the aligning spacer (Fig.
9)
around
the

visible portion
of the
steering shaft

and slide
it up the
shaft into
the
steer-

ing column.
It may be
necessary
to

move
the
shaft back
and
forth
to
com-

pletely install
the
spacer.

9.
At
this point
the
steering column

assembly, being loose,
may
have

dropped toward
the
steering gear

grounding
the
steering shaft
on the

steering gear input shaft.
To
properly

establish
the
steering shaft
to
steering

gear clearance, insert
a 1/8
diameter

rod
or
drill through
the
opening
in the

upper half
of the
flex coupling.

10.
Tighten
to a
snug
fit
(approxi-

mately
2-3
ft-lb)
the
nuts retaining
the

toe plates
to the
dash panel
(B in Fig.

8).

11.
If the
aligning spacer cannot
be

rotated freely,
the
dash panel holes

must
be
filed
or
reamed
for
greater

travel
(as
mentioned
in the
second

paragraph
at the
beginning
of
this

procedure).

12.
Tighten
all
nuts
and
bolts

(noted
as C, D and E in
Fig.
8) in the

passenger compartment
to a
snug
fit

(approximately 2-3 ft-lb). Again check

aligning spacer
for
looseness. Perform

these tightening operations
in
alpha-

betical order.

13.
Tighten
the
lateral adjustment

bolt
(F in Fig. 8) to
snug
fit.
Again

check
the
aligning spacer
for
loose-

ness.

14.
Tighten
all
bolts and nuts
to the

proper torque value (listed
in Fig. 8)

in alphabetical order.

15.
Remove
the
steering shaft
al-

igning spacer.

16.
Remove
the 1/8
diameter
rod or

drill previously inserted
in the
flex

coupling.

17.
Reinstall
the
trim
at the
instru-

ment panel
to
steering column mount-

ing.

LINCOLN CONTINENTAL

If
a
condition
of
high shift
or
steer-

ing effort
is
experienced
it may be

caused
by
improper alignment
of the

energy absorbing steering column.
The

following procedures outline
the
steps

necessary
to
correctly realign either

fixed
or
tilt columns:

1.
Disconnect
the
battery.

2.
Loosen four
toe
plate attaching

nuts (Fig.
10).

3.
Loosen
one toe
plate
to
steering

column clamp bolt
and nut.
Check

alignment
of
steering shaft
to
shift
-HANDLE PORTION

2-3/4"
-*- 3/4"

BEND AROUND

STEERING SHAFT
DIMENSION
A:

STANDARD COLUMN 7/16"

TILT WHEEL COLUMN
1-1/8"

•2-3/4

FABRICATE ALIGNING SPACER OUT OF

PLASTIC SHIPPING COLLAR PROVIDED

ON SERVICE DRIVESHAFTS, OR OUT
OF

1/32"—1/16" CARDBOARD
STEERING SHAFT

ALIGNMENT SPACER-BEND AROUND

STEERING SHAFT (DIMENSION
A)
AND

SLIDE UP THE SHAFT INTO COLUMN

G1537-A

FIG. 9—Aligning Spacer Fabrication
and
Insertion

BRAKE PEDAL

SUPPORT BRACKET

PART

A-TOE PLATE

B-CLAMP

C-C0LUMN BRACKET

D-BRAKE PEDAL

SUPPORT BRACKET
TORQUE VALUE

8-12 FT. LB.

3-5 FT. LB.

10-15
FT.
LB.

8-12 FT. LB.

G1541-A

FIG. 10—Steering Column Alignment Locations
and
Torque

Specifications—Lincoln Continentalprocarmanuals.com