open gas tank FORD MUSTANG 1969 Volume One Chassis

02-01-06

Brakes

02-01-06

side.
Refill the master cylinder reser-

voir after each wheel cylinder is bled

and install the master cylinder cover

and gasket. Be sure the diaphragm

type gasket is properly positioned in

the master cylinder cover. When the

bleeding operation is completed, the

fluid level should be filled to within

1/4 inch of the top of the reservoirs.

7. If the primary (front brake) sys-

tem is to be bled. Repeat steps 2

through 6 at the right front brake cal-

iper or cylinder and ending at the left

front brake caliper or cylinder.

8. On disc brake equipped models

be sure that the front brake pistons

are returned to their normal positions

and that the shoe and lining assem-

blies are properly seated by depressing

the brake pedal several times until

normal pedal travel is established.

9. Centralize the pressure differen-

tial valve. Refer to the Centralizing

the Pressure Differential Valve proce-

dures which follow.

PRESSURE BLEEDING

The Lincoln Continental hydraulic

brake system is to be bled only with

pressure bleeding equipment.

Bleed the longest lines first. The

bleeder tank should contain enough

new Ford Brake Fluid to complete the

bleeding operation. Use Ford Brake

Fluid — Extra Heavy Duty — Part

Number C6AZ-19542-A (ESA-

M6C25-A) or equivalent for all brake

applications. The brake fluid is col-

ored blue for identification purposes.

Do not mix low temperature brake

fluid with the specified brake fluid

during the bleeding operations. Never

re-use brake fluid that has been

drained from the hydraulic system.

The tank should be charged with ap-

proximately 10 to 30 pounds of air

pressure. Never exceed 50 pounds

pressure.

1.
Clean all dirt from the master

cylinder reservoir cover.

2.
Remove the master cylinder res-

ervoir cover and rubber gasket, and

fill the master cylinder reservoir with

the specified brake fluid. Install the

pressure bleeder adapter tool to the

master cylinder, and attach the bleed-

er tank hose to the fittng on the

adapter.

Master cylinder pressure bleeder

adapter tools can be obtained from

the various manufacturers of pressure

bleeding equipment. Follow the in-

structions of the manufacturer when

installing the adapter.

3.
If the master cylinder is

equipped with a bleed screw, loosen
the bleed screw and bleed the master

cylinder until the fluid is free of air

bubbles; then, tighten the bleed screw.

Do not use the secondary piston stop

screw, located on the bottom of the

master cylinder, to bleed the master

cylinder.

4.
If the rear wheel cylinders, the

secondary brake system, are to be

bled, position a 3/8 inch box wrench

(Fig. 9) on the bleeder fitting on the

right rear brake wheel cylinder. At-

tach a bleeder tube to the bleeder fit-

ting. The end of the tube should fit

snugly around the bleeder fitting.

5. Open the valve on the bleeder

tank to admit pressurized brake fluid

to the master cylinder reservoir.

6. Submerge the free end of the

tube in a container partially filled with

clean brake fluid, and loosen the

bleeder fitting.

7.
When air bubbles cease to ap-

pear in the fluid at the submerged end

of the bleeder tube, close the bleeder

fitting and remove the tube.

8. Repeat steps 3 through 7 at the

left rear wheel cylinder.

9. If the vehicle is equipped with

disc brakes, repeat steps 4 through 7,

starting at the right front disc caliper

and ending at the left front disc cali-

per.

On Lincoln Continental models the

front wheel and tire assemblies must
be removed to gain access to the

bleeder fittings on the calipers. Also

on Lincoln Continental models the

metering valve release rod must be

pulled outward and held a minimum

of 1/16 inch (Fig. 10) while bleeding

the primary brake system.

10.
If the vehicle contains drum-

type front brakes and the primary

(front) brake system is to be bled, re-

peat steps 4 through 7, starting at the

right front wheel cylinder ending at

the left front wheel cylinder.

11.
When the bleeding operation is

completed, close the bleeder tank

valve and remove the tank hose from

the adapter fitting.

12.
On disc brake equipped ve-

hicles,
be sure that the front brake

pistons are returned to their normal

positions and that the shoe and lining

assemblies are properly seated by dep-

ressing the brake pedal several times

until normal pedal travel is esta-

blished.

13.
Remove the Pressure Bleeder

Adapter Tool. Fill the master cylinder

reservoirs to within 1/4 inch of the

top.
Install the master cylinder cover

and gasket. Be sure the Diaphragm

type gasket is properly positioned in

the master cylinder cover.

14.
Centralize the pressure differen-

tial valve as follows.

METERING VALVE

BLEEDER RETAINER

SEE

VIEW A

RELEASE ROD

FIG. 10—Disc Brake Metering Valve—Lincoln Continental
HI 644-Aprocarmanuals.com