lock FORD MUSTANG 2003 Workshop Manual

REMOVAL AND INSTALLATION
Module
Removal
1. Remove the hydraulic control unit (HCU). Refer to Hydraulic Control Unit .
2. Remove the pump motor electrical connector.
3. Remove the anti- lock-brake control module screws.
4. Remove the anti- lock-brake control module from the HCU.
Installation
1. NOTE: The brake system must be bled after the HCU is installed or replaced. Refer to Section 206 - 00 .
To install, reverse the removal procedure.
SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Sensor —
Front
Removal 1. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
2. Remove the inner fender splash shield. 1. Remove the inner fender splash shield push pins.
2. Remove the inner fender splash shield screw.
3. Remove the inner fender splash shield.
3. Remove the front anti- lock brake sensor electrical connector.
4. Remove the front anti- lock brake sensor harness from the anti- lock brake sensor harness clips.
5. Remove the front anti- lock brake sensor.
1. Remove the front anti- lock brake sensor bolt.
2. Remove the anti- lock brake sensor harness from the harness clips.
3. Remove the front anti- lock brake sensor.
SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Sensor —
Rear
Removal 1. Remove the rear passenger seat.
2. Disconnect the rear anti- lock brake sensor electrical connector.
3. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
4. Remove the rear anti- lock brake sensor harness from the floor pan.
5. Remove the anti- lock brake sensor harness bracket bolt.
6. NOTE: The sensor may be siezed to the axle. Use Rust Penetrant and Inhibitor F2AZ-19A501-
A meeting Ford specification ESR- M99C56-A to loosen the sensor for removal.
Remove the rear anti- lock brake sensor.
SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1. Remove the rear anti-
lock brake sensor bolt.
2. Remove the rear anti- lock brake sensor.
Installation 1. NOTE: Be sure to apply High Temperature Nickel Anti- Sieze Lubricant F6AZ-9L494-AA
meeting Ford specification ESE-M124A- A to the sensor body where it will make contact when
installed.
To install, reverse the removal procedure. Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Switch —
Traction Control
Removal and Installation 1. NOTE: If the vehicle is equipped with an automatic transmission, position the shift lever in the 1
position before detaching the floor console finish panel.
Lifting from both sides, detach the floor console finish panel.
2. Disconnect the electrical connector and position the finish panel out of the way.
3. Reaching behind the center finish panel, push and detach the switch from the finish panel.
4. Disconnect the electrical connector and remove the switch.
SECTION 206-
09B: Anti-Lock Control — Traction Control 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 211-
00: Steering System — General Information 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricants
Motorcraft MERCON® Multi-Purpose (ATF) Transmission Fluid XT-
2- QDX MERCON®
Power Steering Gear
Turning effort 2.27 Kg (5.0 lb)
Turns lock-to-
lock 2.38
Power Steering Purge Vacuum
Vacuum 68-
85 kPa (20- 25 in/hg) Power Steering Pump —
CII Flow 9.8 liters/minute
(2.6 gpm)
Fluid @ 74°- 80° C (165°-175°
F)
Engine at 1,500 rpm Pressure 1,034 kPa
(150 psi)
Fluid @ 74°- 80° C (165°-175°
F)
Engine at 1,500 rpm Minimum capacity 3.4 liters/minute
(0.9 gpm)
Fluid @ 74°- 80° C (165°-175°
F)
Engine at idle
Pressure at 5,102 kPa (750
psi) Relief pressure 7,240-8,400 kPa
(1,050-1,230 psi) Power Steering Pump —
CIII Flow 9.8 liters/minute
(2.6 gpm)
Fluid @ 74°- 80° C (165°-175°
F)
Engine at 1,500 rpm Pressure 1,034 kPa
(150 psi)
Fluid @ 74°- 80° C (165°-175°
F)
Engine at 1,500 rpm Minimum capacity 4.7 liters/minute
(1.25 gpm)
Fluid @ 74°- 80° C (165°-175°
F)
Engine at idle
Pressure at 5,171 kPa (750 psi) Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Gear
Removal
1. Turn the steering wheel as necessary to position the wheels in the straight- ahead position. Do
not lock the steering column.
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Remove the front wheels and tires. For additional information, refer to Section 204 - 04 .
4. Remove the cotter pin and nut. Discard the cotter pin.
5. Using the special tool, disconnect the tie- rod end.
SECTION 211-
02: Power Steering 2003 Mustang Workshop Manual Special Tool(s)
Teflon Seal Replacer Set
211-
D027 (D90P-3517- A) or
Equivalent Tie Rod End Remover
211-
001 (TOOL- 3290-D) Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Rotate the steering column intermediate shaft as necessary to access the pinch bolt. Remove
and discard the pinch bolt.
7. Lower the vehicle.
8. Turn the steering wheel back to the straight- ahead position. Turn the ignition key to the locked
position.
9. CAUTION: Do not rotate the steering wheel when the lower steering column shaft is
disconnected, or damage to the air bag sliding contact will result.
Disconnect the steering column intermediate shaft coupling (3A525).
10. Remove the nuts, washers and bolts. Position the steering gear (3504) forward.
11. Disconnect the power steering hoses. Remove and discard the seal rings. zPlug or cap the power steering hoses and steering gear ports to prevent damage and the
entry of foreign material. Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 211-
04: Steering Column 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricant
Ignition Lock Grease FOAZ-19584-
A ESA-
M1C232- A
Torque Specifications Description Nm lb-
ft lb-
in Lock cylinder housing screws 22 17 —
Steering column lower bearing retainer bolts 9 — 80
Ignition switch screws 6 — 53
Multi-
function switch screws 3 — 27
Steering wheel bolt 38 28 —
Steering column retaining nuts 15 12 —
Intermediate shaft coupler-
to-steering column shaft bolt 25 19 — Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4 N805572-
S36 Air bag module retaining screws (2 req'd)
5 3L518 Steering wheel spoke cover
(2 req'd)
6 — Lock tabs
7 14A664 Clockspring
8 13318 Turn indicator cancel cam
9 3C610 Snap ring
10 3520 Bearing spring
11 3518 Upper bearing sleeve
12 3517 Upper bearing (small)
13 3517 Lower bearing (large)
14 3524 Shaft assembly
15 390345-
S36 Screw
16 13K359 Multi-
function switch 17 3E695 Lock cam
18 3F609 Tilt wheel handle
19 N806157 Lock cam pivot pin
20 3530 Lower shroud
21 55929 Shroud retaining screws
22 3D544 Release lever
23 3B661 Lock actuator lever (RH)
24 N805856 Lock actuator lever pin
25 3D653 Lock actuator lever (LH)
26 3B664 Lock lever spring (2 req'd)
27 14A099 Wiring shield
28 3D655 Lock lever spring return
29 3E715 Lock lever upper actuator
30 3E696 Lock spring (shaft)
31 11572 Ignition switch
32 N806423-
S56 Steering column mounting lower nuts
33 N806584 Screw
34 3E660 Mounting bracket
35 3D681 Bearing retaining
36 3518 Bearing sleeve
37 3517 Lower bearing
38 3L539 Lower bearing tolerance ring
39 3C131 Sensor ring
40 3520 Bearing spring
41 N808349 Bolt —
flange yoke 42 3N725 Coupling
43 3C611 Tube boot
44 3B676 Intermediate shaft Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...