parking brake FORD MUSTANG 2003 User Guide

REMOVAL AND INSTALLATION
Stabilizer Bar
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle. For additional information, refer to Section 100 - 02 .
2. Disconnect the anti- lock brake sensor wires from the brackets.
3. Remove the parking brake cable brackets. 1. Remove and discard the bolts.
2. Remove the parking brake cable brackets.
4. Remove the bolts and the stabilizer bar (5A772). Discard the bolts.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Disconnect the parking brake cable and conduit from the parking brake lever.
6. Remove the clip and disconnect the parking brake cable and conduit from the rear brake
caliper.
7. Disconnect the parking brake cable and conduit from the knuckle (5A968/5A969).
8. Remove the rear brake disc. For additional information, refer to Section 206 - 04 .
9. Support the lower suspension arm and bushing (5A649) with a jack stand. Klj . 2 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8. Tighten the nut.
9. Make sure the marks on the cam bolt and the upper suspension arm and bushing made during
removal are aligned, and tighten the nut.
10. Lower the suspension and remove the jack stand.
11. Install the rear brake disc. For additional information, refer to Section 206 - 04 .
12. Install the parking brake cable and conduit into the knuckle. Klj . 7 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Connect the parking brake cable and conduit to the rear brake caliper and install the clip.
14. Connect the parking brake cable and conduit to the parking brake lever.
15.
CAUTION: The axle retainer must be tightened with the brakes applied and the
wheels off the ground to make sure of correct bearing seating. Failure to do so can
cause the retainer to loosen, causing extensive vehicle damage and loss of vehicle
control.
Lower the vehicle and apply the parking brake or service brakes.
16. Tighten the retainer.
17. Install the wheel and tire assembly. For additional information, refer to Section 204 - 04
18. Lower the vehicle.
19. Check the wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 - 00 . Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Remove the bolt and the parking brake cable bracket. Discard the bolt.
Vehicles equipped with a 4.6L 2V engine 5. Remove the stabilizer bar (5A772). For additional information, refer to Stabilizer Bar in this
section.
All vehicles 6. Support the differential housing with a jack stand.
7. Position the special tool 014- 00942 under the rear lower suspension arm and bushing- to-axle
pivot bolt.
8. Remove and discard the pivot bolt and nut.
9. Remove the spring (5560). 1. Slowly lower the arm with the special tool 014- 00942.
2. Remove the rear spring and the rear spring insulators (5536). Installation Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Remove the special tool 014-
00942.
6. Raise the suspension until the shock absorber is compressed to the alignment mark (curb height).
7. Tighten the lower arm- to-axle pivot bolt.
8. Lower the rear suspension and remove the jack stand.
Vehicles equipped with a 4.6L 2V engine
9. Install the stabilizer bar. For additional information, refer to Stabilizer Bar in this section.
All vehicles 10. Install the parking brake cable bracket and a new bolt. Klj . 4 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Support the No. 1 crossmember with a jack stand.
3. Remove both wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
4. Remove both mufflers. For additional information, refer to Section 309 - 00 .
5. Remove the driveshaft. For additional information, refer to Section 205 - 01 .
6. Disconnect the parking brake cable and conduits from the parking brake levers.
7. Remove the clip and disconnect the parking brake cable and conduits from the rear brake calipers. SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Rotunda Powertrain Lift
014-00765 or Equivalent Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8. Disconnect the parking brake cable and conduits from the knuckles (5A968/5A969).
9. Remove the bolts and the parking brake cable brackets.
10. Remove the bolts and the rear brake lines.
11. Remove the bolts and the ABS sensors. Klj . 2 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

11. Connect the rear brake lines and install the bolts.
12. Connect the parking brake cable and conduits to the lower suspension arm and bushings and
install the bolts.
13. Connect the parking brake cable and conduits to the knuckles. 14. Connect the parking brake cable and conduits to the rear brake calipers and install the clips. Klj . 7 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

15. Connect the parking brake cable and conduit to the parking brake levers.
16. Install the driveshaft. For additional information, refer to
Section 205 - 01 .
17. Install both mufflers. For additional information, refer to Section 309 - 00 .
18. Install both wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
19. Remove the jack stand from the No. 1 crossmember.
20. Bleed the brake system. For additional information, refer to Section 206 - 00 .
21. Check wheel alignment. Adjust if necessary. For additional information, refer to Section 204 - 00 . Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...