turn signal FORD MUSTANG 2003 User Guide

Output Shaft Speed (OSS) Sensor Harness Connector 1 — NOT USED
2 — Signal Return
3 — TR3A
4 — TR1
5 — TR2
6 — TR4
7 — NOT USED
8 — NOT USED
9 — Fused Power Feed
10 — Starter Control
11 — Reverse
12 — Starter to Starter Interrupt Relay
Pin Number Circuit Circuit Function
1 — Output Shaft Speed (OSS) Sensor
2 — Signal Return
Digital Transmission Range (TR) Sensor Diagnosis Chart Selector Position PID: TR PID: TR_D PID: TR_V (volts)
TR4 TR3A TR2 TR1 TR3A (PCM Pin 64 to sigrtn)
PARK P/N 0 0 0 0 0.0 Volts
In Between REV 0 1 0 0 1.3 -
1.8 Volts REVERSE REV 1 1 0 0 1.3 -
1.8 Volts In Between REV 0 1 0 0 1.3 -
1.8 Volts NEUTRAL NTRL 0 1 1 0 1.3 -
1.8 Volts In Between
O/D
a 1 1 1 0 1.3 -
1.8 Volts OVERDRIVE
O/D
a 1 1 1 1 1.3 -
1.8 Volts In Between Man 2 1 0 1 1 0.0 Volts Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

a
Will read "Drive" if O/D is canceled.
A. TR_V is the voltage at the PCM pin 64 (TR3A Circuit) to signal return.
B. "In Between" reading could be caused by a shift cable or digital TR sensor misaligned or a digital TR sensor circuit failure of TR1, TR2, TR3A, or TR4.
C. TR_D: 1= Open Digital TR switch, 0= Closed Digital TR switch.
D. EEC- V Control System Breakout Box Readings: Taken from PCM signal pins for TR1, TR2,
TR3A, TR4 to signal return.
„Voltages for TR1, TR2, TR4:
„ 0 = 0.0 volts.
„ 1 = 9.0 - 14.0 volts.
„ Voltage for TR3A:
„ 0 = 0.0 volts.
„ 1 = 1.3 - 1.8 volts.
Wiggle Test Information For Open/Shorts
z TR4, TR3A, TR2, and TR1 are all closed in PARK. PARK is a good position to check for
intermittent open circuits (with scan tool monitoring TR_D).
z TR4, TR3A, TR2, and TR1 are all open in OVERDRIVE, so OVERDRIVE is a good position to
check for shorts to ground. To determine the shorted components while observing TR_D,
unplug the TR and see if the short goes away. If the short is still present, unplug the
transmission harness and see if the short goes away. If the short is still present, then the short
is in the PCM or vehicle harness. Remove the suspect circuit(s) wire from the PCM vehicle
harness. If the short is still present, then the PCM has an internal failure. Otherwise the failure is
in the vehicle harness. Manual 2 Man 2 1 0 0 1 0.0 Volts
In Between Man 2 1 0 1 1 0.0 Volts
Manual 1 Man 1 0 0 1 1 0.0 Volts Klj . 4 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

z
Visually inspect the lead frame and connectors for
damage.
z Key in ON position.
z Measure the voltage with the positive lead to VPWR
solenoid pin and negative lead to a good ground.
z Is the voltage greater than 10 volts? GO to
A6 .
No
CHECK for open or short circuit
in harness, or solenoid. A6 ELECTRICAL SIGNAL CHECK
z
Measure the voltage with the positive lead connected to
VPWR solenoid pin and the negative lead to the signal
pin of the appropriate solenoid.
z Enter the following diagnostic mode on the diagnostic
tool: Trans- Bench Mode.
z Select Parameter SSA, SSB or TCC.
z Select "ON".
z Press "SEND".
z Turn the solenoids ON and OFF, while monitoring the
voltage, solenoid state on the scan tool (ON and OFF),
and listen for the solenoid to activate (click).
z Measure the voltage with the positive lead to VPWR pin
and the negative lead to the TCC pin.
z Enter the following diagnostic mode on the diagnostic
tool: Select Parameter TCC.
z Select "ON".
z Press "SEND".
z Turn the solenoid ON and OFF, while monitoring the
voltage, solenoid state on the scan tool (ON and OFF), Yes
GO to
A7 .
No
CHECK for open or short circuit
in harness, solenoid or a PCM
concern. Klj . 5 ba
222003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

harness is wiggled, the sensor is tapped, or the
vehicle driven?
C6 CHECK DIGITAL TRANSMISSION RANGE SENSOR
OPERATION z
Disconnect: Digital TR Sensor .
z CAUTION: Do not pry on connector. This will
damage the connector and result in a transmission
concern.
z Connect: TR- E Cable to Transmission Tester.
z Connect: TR- E Cable to Digital TR Sensor.
z Place the Digital TR Overlay onto Transmission Tester.
z Carry out Sensor Test as instructed on the Digital TR
Overlay.
z Does the status lamp on the tester TRS- E cable
match the selected gear positions? Yes
Concern is not in the digital TR
sensor, GO to
C7 .
No
INSTALL a new digital TR
sensor. CLEAR DTCs and
REPEAT OBD Tests. C7 CHECK PCM HARNESS CIRCUITS FOR OPENS
z
Key in OFF position.
z Disconnect: Powertrain Control Module (PCM) .
z Inspect for damaged or pushed- out pins, corrosion or
loose wires.
z Disconnect: Digital TR Sensor.
z CAUTION: Do not pry the connector. This will
damage the connector and result in a transmission
concern.
z Disconnect the digital TR sensor connector.
z Install the EEC- V Control System Breakout Box.
z Measure the resistance between the PCM test pin 91 at
the EEC- V Control System Breakout Box and signal
return circuit pin 2 at digital TR sensor connector
harness side.
z For vehicles equipped with a 4.6L engine measure the
resistance between the PCM test pin 34 at the EEC- V
Control System Breakout Box and TR1 circuit pin 4 at
digital TR sensor connector harness side.
z For vehicles equipped with a 3.8L engine measure the
resistance between the PCM test pin 3 at the EEC- V Yes
GO to
C8 .
No
REPAIR open circuit(s).
RECONNECT all components.
CLEAR DTCs. REPEAT OBD
Tests. Klj . 11 ba
222003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

D2 SOLENOID FUNCTIONAL TEST
z
Install 2,060 kPa (300 psi) pressure gauge into EPC tap.
z Monitor pressure gauge.
z Enter the following diagnostic mode on the diagnostic tool:
Parameter; EPC.
z Select value - 15, 30, 45, 60, 70 or 90 psi.
z Press "SEND".
z Select another value "0- 90 psi".
z Press "SEND".
z Enter the following diagnostic mode on the diagnostic tool:
XXX.
z Press "SEND".
z Does the pressure reading match the commanded
pressure? Yes
CLEAR DTCs. REPEAT OBD
Tests.
No
GO to
D3 .
D3 CHECK FOR BATTERY VOLTAGE
z
Remove transmission fluid pan.
z Visually inspect the lead frame connectors for damage.
z Key in ON position.
z Measure the voltage with positive lead to VPWR solenoid
pin and negative lead to a good ground.
z Is voltage greater than 10 volts? Yes
GO to
D4 .
No
REPAIR the circuit. CLEAR
the DTCs. REPEAT the OBD
Tests. D4 ELECTRICAL SIGNAL CHECK
z
Measure the voltage with positive lead connected to
VPWR solenoid pin and connect negative lead to the
signal pin of the EPC solenoid.
z Turn the solenoids ON and OFF, while monitoring the
voltage reading, solenoid state on the scan tool (ON and
OFF), listen for the solenoid to activate (click).
z Enter the following diagnostic mode on the diagnostic tool:
Trans- Bench Mode.
z Enter the following diagnostic mode on the diagnostic tool:
Parameter EPC.
z Select a value "0- 90 psi".
z Press "SEND".
z Select another value "0- 90 psi".
z Press "SEND".
z Enter the following diagnostic mode on the diagnostic tool: Yes
GO to
D5 .
No
CHECK for open or short
circuit in harness or PCM. Klj . 18 ba
222003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Speed Control
Refer to Wiring Diagrams Cell
31 , Speed Control for schematic and connector information.
Principles of Operation
The speed control system is designed to maintain vehicle speed above 48 km/h (30 mph). After the
ON switch is depressed, depressing the SET/ACCEL switch will activate the speed control servo. To
increase a set speed, either depress and hold for continuous acceleration, or momentarily tap the
SET/ACCEL switch for 1.6 km/h (1 mph) acceleration increments. To decrease a set speed, depress
and hold the COAST switch until the target speed is reached, or momentarily tap the COAST switch
for 1.6 km/h (1 mph) deceleration increments. When the speed control system has been disabled by
tapping the brake pedal, the RESUME switch can be depressed and the vehicle will return to the
original set speed if the vehicle is traveling over 48 km/h (30 mph) and the OFF switch has not been
depressed.
NOTE: The deactivator switch is provided as an additional safety feature. Normally, when the brake
pedal is depressed, an electrical signal from the brake lamp circuit to the speed control servo will
deactivate the system. Under increased brake pedal effort, the deactivator switch will open and
remove power to the speed control servo, releasing the throttle independent of the speed control
servo.
NOTE: The air bag sliding contract provides the electrical interface between the steering column wiring
and the speed control actuator switches in the steering wheel.
The inputs to the speed control servo are the:
zvehicle speed signal.
SECTION 310-
03: Speed Control 2003 Mustang Workshop Manual Special Tool(s)
Worldwide Diagnostic System
(WDS)
418-
F224,
New Generation STAR (NGS)
Tester
418- F052, or equivalent
diagnostic tool 73 Digital Multimeter or
equivalent
105-
R0051 Breakout Box, EEC-V Control
System 418-049, or equivalent
014- 00950 Klj . 1 ba
132003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

tool:
z Monitor the PCM PID WACF while turning the function
selector.
z Does the PCM PID WACF read YES? Control/Emissions Diagnosis
(PC/ED) manual.
No
GO to
C3 .
C3 CHECK THE PCM PID ACCS WITH THE A/C ON
z
Key in START position.
z Make sure the engine is at idle.
z Enter the following diagnostic mode on the diagnostic
tool: PCM PID ACCS.
z Monitor the PCM PID ACCS while turning the function
selector.
z Does the PCM PID ACCS read ON? Yes
GO to
C4 .
No
GO to C6 .
C4 CHECK PCM PID WAC WITH THE A/C ON
NOTE:
When PCM PID WACF is YES, this is the same
fault as DTC P1460.
z Enter the following diagnostic mode on the diagnostic
tool: PCM PID WAC.
z Monitor the PCM PID WAC while turning the function
selector.
z Does the PCM PID WAC read ON? Yes
GO to
C20 .
No
GO to C5 .
C5 CHECK THE INPUT SIGNAL TO THE PCM
z
Key in OFF position.
z Disconnect: PCM C175.
z Key in ON position.
z Measure the voltage at PCM C175- 41, circuit 198
(DG/OG), harness side and ground.
z Is the voltage reading greater than 10 volts? Yes
INSTALL a new powertrain
control module. TEST the
system for normal operation.
No
GO to
C6 .
C6 CHECK THE REFRIGERANT PRESSURE
z
Key in OFF position.
z Connect the manifold gauge set. Refer to Refrigerant System Tests in this section.
z Is the system pressure 345- 1,724kPa (50-250psi)? Yes
GO to
C7 .
No
REPAIR the leaks and
RETEST the system for normal
operation. REFER to Section 412 - 03 .
C7 CHECK THE SUPPLY TO THE FUNCTION SELECTOR
SWITCH z
Key in OFF position.
z Disconnect: Function Selector Switch C294c.
z Key in ON position.
z Measure the voltage at the function selector switch
C294c- 2, circuit 883 (PK/LB), harness side and ground. Yes
GO to
C17 .
No
GO to C8 . Klj . 16 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

PINPOINT TEST D: THE A/C IS ALWAYS ON z
Is the resistance less than 5 ohms? No
REPAIR circuit 1205 (BK) for
an open. TEST the system for
normal operation.
Test Step Result / Action to Take
D1 CHECK PCM PID WACF
z
Turn the function selector switch to the OFF position.
z Key in ON position.
z Enter the following diagnostic mode on the diagnostic
tool: PCM PID WACF.
z Does the PCM PID WACF read YES? Yes
REPAIR circuit 331 (PK/YE) for
a short to ground. TEST the
system for normal operation.
No
GO to
D2 .
D2 CHECK PID ACCS WITH A/C OFF
z
Enter the following diagnostic mode on the diagnostic
tool: PCM PID ACCS.
z Does the PCM PID ACCS read ON? Yes
GO to
D3 .
No
GO to D5 .
D3 CHECK FOR A FALSE INPUT SIGNAL TO THE PCM
z
Key in OFF position.
z Disconnect: PCM C175.
z Key in ON position.
z Turn the function selector switch to the OFF position.
z Measure the voltage between PCM C175- 41, circuit 198
(DG/OG) harness side and ground.
z Is the voltage greater than 10 volts? Yes
GO to
D4 .
No
INSTALL a new powertrain
control module. REFER to
Section 303 - 14 . TEST the
system for normal operation. D4 CHECK CIRCUIT 198 (DG/OG) FOR A SHORT TO B+
z
Key in OFF position.
z Disconnect: Function Selector Switch C294c.
z Connect: PCM C175.
z Key in ON position.
z Measure the voltage at the function selector switch Yes
REPAIR circuit 348 (PK) for a
short to B+. TEST the system
for normal operation. Klj . 24 ba
412003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Instrument Cluster
The instrument cluster (10849) consists of the following components:
Instrument Cluster—
Base 3.8L Engine
SECTION 413-
01: Instrument Cluster 2003 Mustang Workshop Manual Item Part
Number Description
1 — Fuel gauge
2 — Engine coolant temperature gauge
3 — Speedometer
4 — Turn signal/hazard indicator
5 — High beam indicator
6 — Tachometer
7 — Odometer
8 — Trip odometer reset button
9 — Voltmeter gauge
10 — Oil pressure gauge
11 — CHECK FUEL CAP indicator
12 — BRAKE warning indicator
13 — ABS warning indicator
14 — Traction control indicator
15 — Overdrive off (O/D OFF) indicator (automatic Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Instrument Cluster—
Base 4.6L Engine transmission)
16 — LOW FUEL level indicator
17 — SERVICE ENGINE SOON indicator
18 — THEFT indicator
19 — AIR BAG warning indicator
20 — Charging system indicator
21 — Safety belt warning indicator
Item Part
Number Description
1 — Fuel gauge
2 — Engine coolant temperature gauge
3 — Speedometer
4 — Turn signal/hazard indicator
5 — High beam indicator
6 — Tachometer
7 — Odometer
8 — Trip odometer reset button
9 — Voltmeter gauge
10 — Oil pressure gauge
11 — CHECK FUEL CAP indicator
12 — BRAKE warning indicator
13 — ABS warning indicator Klj . 2 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...