wheel FORD MUSTANG 2003 Workshop Manual

2. Install the steering gear into the special tools.
3. Clean the exterior of the steering gear with solvent. If necessary, drain any excess power
steering fluid.
4. Inspect the steering gear housing for cracks and other damage. If necessary, install a new steering gear.
5. Verify the power steering gear input shaft bearing rotates freely. If necessary, install a new steering gear.
6. Place an alignment mark on the tie- rod ends, nuts and front wheel spindle tie- rods. Remove the
tie- rod ends and nuts.
7. CAUTION: Use care not to damage the front suspension steering ball stud dust
seals. If the front suspension steering ball stud dust seals are damaged, this will allow
contamination into the steering gear and cause leakage.
Remove the clamps and the two front suspension steering ball stud dust seals.
zDiscard any clamps that are damaged or excessively corroded.
z Discard any front suspension steering ball stud dust seals that are damaged. Klj . 2 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8.
CAUTION: Place the steering gear at the center position. Use a crowfoot on the flat
of the rack gear to resist rotation and prevent damage to the steering gear during
removal and installation of the front wheel spindle tie- rods.
Place the steering gear at the center position. Install a crowfoot on the flat of the steering gear.
Using the special tool remove the front wheel spindle tie- rods.
Steering gears equipped with travel restrictors 9. NOTE: Some steering gears may contain one or two rack travel restrictors on each side of the
steering gear. The restrictors are split washers and can be removed if necessary.
Remove the travel restrictors.
zDiscard any travel restrictors that are heavily worn.
All steering gears 10. Remove the steering gear from the special tools.
Assembly
All steering gears 1. Install the steering gear in the special tools.
Steering gears equipped with travel restrictors 2. Install the travel restrictors. zInstall new travel restrictors as necessary. All steering gears Klj . 3 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

3.
CAUTION: Place the steering gear at the center position. Use a crowfoot on the flat
of the rack gear to resist rotation and prevent damage to the steering gear during
removal and installation of the front wheel spindle tie- rods.
Place the steering gear at the center position. Install a crowfoot on the flat of the steering gear.
Using the special tool install the front wheel spindle tie- rods.
4. Thoroughly clean the steering gear of any foreign material.
5. CAUTION: Use care not to damage the front suspension steering ball stud dust
seals. If the front suspension steering ball stud dust seals are damaged, this will allow
contamination into the steering gear and cause leakage.
Install the front suspension steering ball stud dust seals and clamps.
zPosition the front suspension steering ball stud seals and steering gear rack tubes as
shown.
z Install new front suspension steering ball stud dust seals and clamps as necessary.
z To prevent the front suspension steering ball stud dust seals from twisting during toe
adjustment, apply grease to the groove in the front wheel spindle tie- rods and uniformly
to the inner- diameter of the front suspension steering ball stud dust seals. Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Install the nut and the tie-
rods ends. Align the marks.
z Apply silicone dielectric compound to the front wheel spindle tie- rod threads.
7. Remove the steering gear from the special tools.
8. Install the steering gear mounting bracket housing insulators. zInstall new steering gear mounting bracket housing insulators as necessary.
z The large end of the metal sleeve must be positioned downward.
z Check that the mounting surfaces are clean and free of foreign material. Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

SPECIFICATIONS
SECTION 211-
04: Steering Column 2003 Mustang Workshop Manual General Specifications
Item Specification
Lubricant
Ignition Lock Grease FOAZ-19584-
A ESA-
M1C232- A
Torque Specifications Description Nm lb-
ft lb-
in Lock cylinder housing screws 22 17 —
Steering column lower bearing retainer bolts 9 — 80
Ignition switch screws 6 — 53
Multi-
function switch screws 3 — 27
Steering wheel bolt 38 28 —
Steering column retaining nuts 15 12 —
Intermediate shaft coupler-
to-steering column shaft bolt 25 19 — Klj . 1 ba
12003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Steering Column
SECTION 211-
04: Steering Column 2003 Mustang Workshop Manual Item Part Number Description
1 043B13 Driver air bag module
2 N804385-
S100 Steering wheel bolt
3 3600 Steering wheel Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4 N805572-
S36 Air bag module retaining screws (2 req'd)
5 3L518 Steering wheel spoke cover
(2 req'd)
6 — Lock tabs
7 14A664 Clockspring
8 13318 Turn indicator cancel cam
9 3C610 Snap ring
10 3520 Bearing spring
11 3518 Upper bearing sleeve
12 3517 Upper bearing (small)
13 3517 Lower bearing (large)
14 3524 Shaft assembly
15 390345-
S36 Screw
16 13K359 Multi-
function switch 17 3E695 Lock cam
18 3F609 Tilt wheel handle
19 N806157 Lock cam pivot pin
20 3530 Lower shroud
21 55929 Shroud retaining screws
22 3D544 Release lever
23 3B661 Lock actuator lever (RH)
24 N805856 Lock actuator lever pin
25 3D653 Lock actuator lever (LH)
26 3B664 Lock lever spring (2 req'd)
27 14A099 Wiring shield
28 3D655 Lock lever spring return
29 3E715 Lock lever upper actuator
30 3E696 Lock spring (shaft)
31 11572 Ignition switch
32 N806423-
S56 Steering column mounting lower nuts
33 N806584 Screw
34 3E660 Mounting bracket
35 3D681 Bearing retaining
36 3518 Bearing sleeve
37 3517 Lower bearing
38 3L539 Lower bearing tolerance ring
39 3C131 Sensor ring
40 3520 Bearing spring
41 N808349 Bolt —
flange yoke 42 3N725 Coupling
43 3C611 Tube boot
44 3B676 Intermediate shaft Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Ignition Switch Lock Cylinder —
Non-Functional
Removal and Installation 1. NOTE: Make sure the front wheels are in the straight- ahead position.
Disconnect the battery ground cable (14301) and wait at least one minute to allow the depletion
of the restraint system backup power supply. For additional information, refer to Section 414 -
01 .
2. WARNING: To avoid the risk of serious personal injury, read and follow all
warnings, cautions, notes and instructions in the deactivation procedure.
Deactivate the supplemental restraint system (SRS). For additional information, refer to
Supplemental Restraint System (SRS) Deactivation and Reactivation in this section.
3. WARNING: To reduce the risk of serious personal injury, read and follow all
warnings, cautions, notes and instructions in the steering wheel removal and installation
procedure.
Remove the steering wheel assembly. For additional information, refer to Wheel in this section.
4. Twist off the cap from the ignition switch cylinder.
5. NOTE: The lock cylinder is repaired by discarding the inoperative lock cylinder and building a
new lock cylinder using the appropriate lock repair package (F85Z-11582- AA). The lock repair
package includes a detailed instruction sheet to build the new lock cylinder to the current key
code of the vehicle.
SECTION 211-
04: Steering Column 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Wheel
Removal and Installation
1. Disconnect the battery ground cable (14301) and wait at least one minute to allow the depletion of the restraint system backup power supply. For additional information, refer to Section 414 -
01 .
2. Turn the steering wheel to the straight- ahead position and the ignition switch to the OFF
position.
3. WARNING: To avoid the risk of serious personal injury, follow all warnings,
cautions, notes and instructions in the beginning of the deactivation procedure.
Deactivate the supplemental restraint system (SRS). For additional information, refer to
Supplemental Restraint System (SRS) Deactivation and Reactivation in this section.
4. WARNING: To avoid risk of serious personal injury, follow all warnings, cautions,
notes and instructions in the driver air bag removal and installation procedure.
Remove the driver air bag module. For additional information, refer to Section 501 - 20B .
5. Remove and discard the steering wheel retaining bolt.
6. CAUTION: Removing the steering wheel without using a puller can damage the
column bearings.
Use a suitable puller to remove the steering wheel (3600).
SECTION 211-
04: Steering Column 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

7. Remove the steering wheel while routing the wires from the clockspring through the steering
wheel.
8. To install, reverse the removal procedure.
9. WARNING: To avoid the risk of serious personal injury, follow all warnings,
cautions, notes and instructions at the beginning of the reactivation procedure.
Reactivate the supplemental restraint system (SRS). For additional information, refer to
Supplemental Restraint System (SRS) Deactivation and Reactivation in this section. Klj . 2 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...