wheel FORD MUSTANG 2003 Workshop Manual

Clutch Disc and Clutch Pressure Plate —
4.6L (2V) 7 7548 Clutch release hub and bearing
8 7515 Clutch release lever
9 7B602 Clutch release lever stud
10 N606063-S2 Bolt (6 req'd)
11 6392 Flywheel housing
12 7050 Main drive gear bearing retainer
13 55981-
S36 M Bolt
14 7513 Clutch release lever dust shield
15 N807508-S2 Screw and washer assembly
Item Part Number Description
1 6375 Flywheel
2 6397 Flywheel to clutch pressure plate dowel (3
req'd)
3 7600 Pilot bearing
4 7550 Clutch disc
5 7563 Clutch pressure plate
6 7515 Clutch release lever
7 7B602 Clutch release lever stud
8 N606063-S2 Bolt (6 req'd)
9 6392 Flywheel housing
10 55981-
S36M Bolt
11 7513 Clutch release lever dust shield Klj . 2 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

Clutch Disc and Clutch Pressure Plate —
4.6L (4V)
z The clutch is a single plate, dry friction clutch disc. The clutch disc has a splined hub with
integral torsional springs. The clutch disc hub attaches to the input shaft.
z Engine output is coupled to the transmission input shaft by friction existing between the clutch
disc facings and the flywheel/clutch pressure plate assembly. The extent of this friction is directly related to the composition of the facing material and the magnitude of the clamping 12 7548 Clutch release hub and bearing
13 N808969-
S100 Bolt
14 N808969-
S100 Bolt (6 req'd)
15 — Rear face of block and flywheel (part of 6010)
16 — Bolt (3 req'd)
17 6397 Flywheel housing to block dowel (2 req'd)
Item Part Number Description
1 6375 Flywheel
2 7600 Pilot bearing
3 7550 Clutch disc
4 7563 Clutch pressure plate
5 7548 Clutch release hub and bearing
6 7515 Clutch release lever
7 7B602 Clutch release lever stud
8 6392 Flywheel housing
9 N808969-S100 Clutch pressure plate bolt (6 req'd) Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

forces exerted by the clutch pressure plate and the flywheel on the facings. These factors limit
the amount of torque that can be transmitted without slippage.
z The clamping force is obtained from a diaphragm spring contained within the clutch pressure
plate assembly. This force is developed during the attachment of the clutch pressure plate
assembly to the flywheel.
z The clutch system is disengaged when the clutch pedal is pressed and is accomplished when
the release fingers are fully displaced toward the flywheel. This displacement removes the
spring load from the clutch pressure plate and eliminates the coupling friction between the
engine and the transmission.
z When the clutch pedal is depressed a cable connected to the clutch release lever, hub and
bearing actuates the clutch pressure plate diaphragm spring, releasing pressure on the clutch
disc. This eliminates the engagement between the transmission and the engine. Klj . 4 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Manual Transmission and Clutch
Inspection and Verification
It is important to get an accurate description of the concern before any diagnosis can be carried out.
Ask questions as to whether it occurs when hot or cold, during shifting, driving at a particular speed or
in a particular gear. If possible, have the customer demonstrate the concern.
zWith the vehicle at a complete stop, shift through all the gears and evaluate the noise at
different engine rpm. Check for any noises in NEUTRAL at different engine rpm.
Symptom Chart SECTION 308-
00: Manual Transaxle/Transmission and Clutch — General
Information 2003 Mustang Workshop
Manual Symptom Chart
Condition
Possible Sources Action
z Clutch slippage zClutch pedal
sticking.
z Pressure plate
diaphragm
spring damaged
or weakened.
z Clutch pressure
plate damaged.
z Clutch disc
facing damaged
or worn
excessively.
z Clutch disc
facing surface
hardened or oil-
coated.
z Clutch release
hub and bearing
binding.
z Flywheel glazed
or damaged.
z loose pressure
plate to flywheel
bolts z
Go To Pinpoint Test A .
z Clutch chatter or shudder zLoose or worn
engine mount.
z Loose pressure
plate to flywheel
bolts
z Oil on clutch
disc facing.
z Clutch pressure
plate damaged z
Go To Pinpoint Test B . Klj . 1 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

or excessive
runout.
z Clutch disc
facing surface
hardened or
damaged.
z Flywheel
surface glazed
or damaged.
z Transmission
input shaft
eccentric or not
perpendicular.
z Clutch drag zClutch drag.
z Cable release
linkage outside
the flywheel
housing worn,
cracked, bent.
z Excessive
runout or
damaged clutch
disc.
z Clutch disc
splines rusted or
worn.
z Loose pressure
plate to flywheel
bolts. z
Go To Pinpoint Test C .
z Clutch pedal pulsation zClutch disc
damaged or
worn.
z Excessive
flywheel runout.
z Loose pressure
plate to flywheel
bolts.
z Improperly
assembled
release lever to
pivot stud. z
Go To Pinpoint Test D .
z Clutch related vibrations zEngine
component
grounding
against frame.
z Loose flywheel
bolts.
z Excessive
flywheel runout.
z Imbalanced
clutch pressure
plate.
z Accessory drive
belt loose or
damaged. z
Go To Pinpoint Test E .
z Hard shifting zManual
transmission
concern.
z Loose pressure
plate to flywheel
bolts. z
Go To Pinpoint Test F . Klj . 2 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

z
Excessive noise zPilot bearing
worn or
damaged.
z Excessive
crankshaft end
play. z
Go To Pinpoint Test G .
z Transmission difficult to
shift z
Lubricant. zADD or DRAIN AND
FILL with specified
lubricant.
z Internal shift
mechanism. z
CHECK the internal shift
mechanism for smooth
operation. REPAIR or
INSTALL a new
mechanism as
necessary.
z Sliding gears,
synchronizers. z
CHECK for free
movement of gears and
synchronizers. REPAIR
or INSTALL new
components as
necessary.
z Housings, shaft. zCHECK for binding
condition between the
input shaft and the
engine crankshaft pilot
bearing or bushing.
REPAIR or INSTALL
new components as
necessary. REFER to
Section 308 - 03A or
Section 308 - 03B .
z Loose pressure
plate to flywheel
bolts. z
CHECK for loose bolts
at the pressure plate.
INSTALL new
components as
necessary. REFER to
Section 308 - 01 .
z NOTE: While verifying
the condition, determine
whether the noise is gear
rollover noise, release
bearing rub or some
other transmission-
related noise. Gear
rollover noise, inherent in
manual transmissions, is
caused by the constant
mesh gears turning at the
engine idle speed while
the clutch is engaged and
the transmission is in
NEUTRAL. Release
bearing rub is sometimes
mistaken for mainshaft
bearing noise. Gear
rollover noise will
disappear when the
clutch is disengaged or
when the transmission is
engaged in gear. z
Lubricant. zADD or DRAIN AND
FILL with specified
lubricant. Klj . 3 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

Release bearing rub will
disappear when the
clutch is engaged. In the
event that a bearing is
damaged, the noise is
more pronounced while
engaged in gear under
load or coast than in
NEUTRAL.
Noisy in forward gears
zComponents
grounding out
on the
transmission. z
CHECK for screws,
bolts, etc., of body or
other components
grounding out.
CORRECT as
necessary.
z Components
housing bolts. z
CHECK the torque on
the transmission-to-
flywheel housing bolts
and the flywheel
housing- to-engine block
bolts. TIGHTEN the
bolts to specification.
REFER to Section 308 -
01 .
z Bearings or
gears. z
INSPECT the bearings.
INSPECT the gears and
gear teeth for wear or
damage. INSTALL new
components as
necessary. REFER to
Section 308 - 01 .
z Gears clash when
shifting from one forward
gear to another z
Pilot bearing. zCHECK for a binding
condition between the
input shaft and the
engine crankshaft pilot
bearing. INSTALL new
components as
necessary. REFER to
Section 308 - 01 .
z Gear teeth
and/or
synchronizer. z
REPAIR or INSTALL
new components as
necessary. REFER to
Section 308 - 03A or
Section 308 - 03B .
z Engine idle
speed too high. z
REFER to the
Powertrain
Control/Emissions
Diagnosis (PC/ED)
manual.
z Transmission jumps out
of gear z
Transmission
range selector
lever boot. z
INSTALL a new boot if
exceptionally stiff.
REFER to Section 308 -
03A or
Section 308 -
03B .
z Transmission-to-
engine mounting
bolts. z
TIGHTEN the bolts to
specification. Klj . 4 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

Pinpoint Tests
PINPOINT TEST A: CLUTCH SLIPPAGE
PINPOINT TEST B: CLUTCH CHATTER OR SHUDDER z
Shafts or bore.
z Overloading of
vehicle.
z Incorrect
preload.
z Input shaft oil
dam. z
Install new components
as necessary and verify
the oil dam installation is
correct. REFER to
Section 308 - 03A or
Section 308 - 03B .
CHECK for correct
installation of the snap
ring on the mainshaft
next to the oil dam.
z Oil baffle in the
input bearing
shim pack. z
INSTALL a new oil
baffle, making sure it is
not damaged during
assembly. REFER to
Section 308 - 03A or
Section 308 - 03B .
Test Step Result / Action to Take
A1 INSPECT THE CLUTCH LINKAGE
z
Key in OFF position.
z Block the wheels and apply the parking brake.
z Depress and slowly release the clutch pedal.
z Does the clutch pedal release without
binding? Yes
GO to
A2 .
No
INSPECT the clutch pedal. REFER to
Section 308 - 02 .
A2 CARRY OUT A STALL TEST
z
Key in START position.
z Block the wheels and apply the parking brake.
z Place the transmission in fourth gear.
z Increase the engine speed to 2000 rpm and
slowly release the clutch pedal.
z Does the engine stall within five seconds? Yes
The clutch is not slipping. VERIFY the
customer concern.
No
INSPECT the clutch components for
damage.
Test Step Result / Action to Take
B1 CHECK ENGINE OR TRANSMISSION MOUNTS
z
Inspect all the engine and transmission mounts
for looseness or damage. Refer to Section 303 -
01A or
Section 303 - 01B and
Section 308 - 03A or
Section 308 - 03B .
z Are any of the engine or transmission mounts Yes
TIGHTEN or INSTALL new engine
mounts or transmission mounts. TEST
the system for normal operation. Klj . 7 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

PINPOINT TEST C: CLUTCH DRAG loose or damaged? No
GO to
B2 .
B2 INSPECT PRESSURE PLATE BOLTS
z
Inspect the pressure plate- to-flywheel bolts.
z Are any of the pressure plate- to-flywheel bolts
loose? Yes
TIGHTEN or INSTALL new bolts.
REFER to
Section 308 - 01 . TEST the
system for normal operation.
No
GO to B3 .
B3 INSPECT PRESSURE PLATE
z
Remove the clutch pressure plate. Refer to
Section 308 - 01 .
z Inspect the clutch pressure plate. Refer to
Pressure Plate Check .
z Are any signs of damage present on the clutch
pressure plate? Yes
INSTALL a new clutch pressure plate.
REFER to
Section 308 - 01 . TEST the
system for normal operation.
No
GO to B4 .
B4 CHECK CLUTCH DISC
z
Carry out the clutch disc inspection procedure.
Refer to Disc Check .
z Is the clutch disc OK? Yes
GO to
B5 .
No
INSTALL a new clutch disc. REFER to
Section 308 - 01 . TEST the system for
normal operation. B5 INSPECT THE FLYWHEEL
z
Inspect the flywheel for damage and runout. Refer
to Flywheel Runout Check .
z Is the flywheel OK? Yes
GO to
B6 .
No
REPAIR or INSTALL a new flywheel
as necessary. REFER to Section 308 -
01 . TEST the system for normal
operation. B6 INSPECT THE INPUT SHAFT
z
INSPECT the input shaft for signs of wear or
damage.
z Are any signs of wear or damage present on
the input shaft? Yes
INSTALL a new input shaft. REFER to
Section 308
- 03A or
Section 308 - 03B .
No
VERIFY the customer concerns. GO
to Symptom Chart if necessary.
Test Step Result / Action to Take
C1 CHECK HIGH SHIFTING EFFORTS
z
Key in START position.
z Set parking brake.
z With the shift control selector in REVERSE, Yes
Clutch system OK.
No Klj . 8 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

PINPOINT TEST D: CLUTCH PEDAL PULSATION clutch disengaged and engine idling, move
the shift lever to a position halfway between
REVERSE and NEUTRAL.
z Slowly engage clutch. The transmission will
behave as if it is in NEUTRAL.
z Gear clash can now be heard if an attempt
is made to shift into REVERSE with the
clutch engaged. Reserve can now be
measured.
z While maintaining light pressure on the shift
selector, slowly press the clutch pedal to the
floor. The gear clash will stop and the shift
selector will slide into the REVERSE
position.
z Is there a minimum 19.05 mm (0.750 inch)
clutch pedal reserve? CHECK the clutch pressure plate and clutch
disc. INSTALL a new clutch pressure plate
or clutch disc if necessary. REFER to
Section 308
- 01 . TEST the system for
normal operation. Test Step Result / Action to Take
D1 CHECK THE CLUTCH PEDAL
PULSATION z
Key in START position.
z With the transmission in NEUTRAL,
slowly press the clutch pedal.
z Does the clutch pedal pulsate while
being pressed? Yes
GO to
D2 .
No
VERIFY customer concern. GO to Symptom Chart if necessary.
D2 INSPECT PRESSURE PLATE BOLTS
z
Inspect the pressure plate- to-flywheel
bolts.
z Are any of the pressure plate- to-
flywheel bolts loose? Yes
TIGHTEN or INSTALL new bolts. REFER to
Section 308
- 01 . TEST the system for normal
operation.
No
GO to D3 .
D3 INSPECT THE CLUTCH PRESSURE
PLATE z
Remove the clutch pressure plate.
Refer to Section 308 - 01 .
z INSPECT the clutch pressure plate for
damage. Refer to Pressure Plate Check .
z Are there any signs of damage
present on the clutch pressure plate? Yes
INSTALL a new clutch pressure plate. REFER
to
Section 308 - 01 . TEST the system for normal
operation.
No
GO to D4 .
D4 INSPECT THE CLUTCH DISC
z
Carry out the clutch disc inspection
procedure. Refer to Disc Check .
z Is the clutch disc OK? Yes
GO to
D5 .
No
INSTALL a new clutch disc. REFER to Section 308 - 01 . TEST the system for normal operation.
D5 INSPECT THE FLYWHEEL Klj . 9 ba
152003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...