Test G FORD MUSTANG 2003 Workshop Manual

DIAGNOSIS AND TESTING
Multifunction Electronic Module
For warning chime concerns, refer to
Section 413 - 09 .
For courtesy lamps/illuminated entry and battery saver concerns, refer to Section 417 - 02 .
For one- touch window concerns, refer to Section 501 - 11 .
For wiper/washer control and interval timer concerns, refer to Section 501 - 16 .
For keyless entry and power door lock concerns, refer to Section 501 - 14B .
For anti- theft concerns, refer to Section 419 - 01 .
SECTION 419-
10: Multifunction Electronic Control Modules 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Body System
Inspection and Verification
Leaks
NOTE:
Trim will reveal the location of most leaks.
1. Remove any trim or carpet in the general area of the leak.
2. Road test or water test the vehicle.
3. Inspect for a dust pattern around the area in question. Inspect for water paths near and above the area in question.
4. Some leaks can be located by placing bright light under the vehicle, removing any necessary trim or carpet, and inspecting the interior of the body at joints and weld lines.
Noise
Wind noise, rattles, and their sources are detected by driving the vehicle at highway speeds. The
vehicle should be driven in four different directions with all of the windows closed, the radio off, the
blower motor off, and all of the ventilation ducts open.
Most wind noise leaks will occur at the door and window seals or at the sheet metal joints in the door
or the door opening.
Symptom Chart SECTION 501-
00: Body System — General Information 2003 Mustang Workshop Manual Symptom Chart
Condition
Possible Sources Action
z Dust and
Water Leaks z
Body sealer missing.
z Opening in weldings
or body joints.
z Components not fully
installed.
z Components missing.
z Components
damaged. z
REMOVE trim panel. CHECK
for leaks and SEAL with
appropriate sealer. ROAD
TEST or WATER TEST for
leaks. RECHECK for leaks;
USE light under the vehicle
with trim removed. CHECK
interior of body at joints and
weld lines.
z Dust/Water
Leaks at Floor
Pan and
Grommets z
Missing or damaged
plugs and/or
grommets. z
CHECK plugs for proper
installation. REPLACE if
necessary.
z Door Drain
Holes
Collecting
Water z
Holes clogged with
mud or road tar. z
CLEAN drain holes of dirt and
foreign material. CHECK drain
holes regularly. TEST the
system for normal operation. Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Wind Noise,
Air Entering
Vehicle
Through Small
Holes in Body z
Leaks at door and
window seals or
sheet metal joints in
doors or door
openings. z
SEAL leaks with Silicone
Gasket and Sealant F7AZ-
19554- EA meeting Ford
specifications WSK-M2G343-
A4. ROAD TEST.
z Rattles zLoose objects in
wells, pillars, and
quarter panels.
z Misalignment (if
tightening bolts does
not eliminate rattle).
z Weatherstripping
and/or anti- squeak
material. z
CHECK doors by carefully
STRIKING underside of door
with a rubber mallet. LISTEN
for loose objects in door.
REPAIR. TIGHTEN body bolts
and screws.
z ADJUST the alignment of the
doors or panels.
z APPLY additional sealer.
INSTALL in proper location to
eliminate rattle. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Rear View Mirrors
Refer to Wiring Diagrams Cell
124 , Power Mirrors for schematic and connector information.
Inspection and Verification 1. Verify the customer concern by operating the system.
2. Visually inspect for obvious signs of mechanical or electrical damage.
3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
4. If the concern is not visually evident, verify the symptom and refer to the Symptom Chart.
Symptom Chart
Refer to the Wiring Diagrams for connector numbers stated in the pinpoint tests. SECTION 501-
09: Rear View Mirrors 2003 Mustang Workshop Manual Special Tool(s)
73III Automotive Meter
105-
R0057 or equivalent Flex Probe Kit
105-
R025B or equivalent
Visual Inspection Chart Mechanical Electrical
z
Exterior rear view mirrors
z Interior rear view mirror z
Central junction box (CJB) fuse 19 (15A)
z Wiring harness
z Connections
z Exterior rear view mirror control
z Exterior rear view mirror motor
SYMPTOM CHART Condition
Possible Sources Action
z The mirrors are inoperative zExterior rear view
mirror control. z
Go To Pinpoint Test A . Klj . 1 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Pinpoint Tests
PINPOINT TEST A: THE MIRRORS ARE INOPERATIVE z
Central junction box
(CJB) fuse 19 (15A).
z Circuitry.
z A single mirror is inoperative zExterior rear view
mirror control.
z Exterior rear view
mirror motor.
z Circuitry. z
Go To Pinpoint Test B .
z A single mirror does not
function with switch logic z
Exterior rear view
mirror control.
z Exterior rear view
mirror motor.
z Circuitry. z
Go To Pinpoint Test C .
Test Step Result / Action to
Take A1 CHECK CIRCUIT 326 (WH/VT)
z
Disconnect: Exterior Rear View Mirror Control C527.
z Measure the voltage between exterior rear view mirror control
C527 pin 1, circuit 326 (WH/VT), harness side and ground.
z Is the voltage greater than 10 volts? Yes
GO to
A2 .
No
REPAIR the circuit.
TEST the system for
normal operation. A2 CHECK CIRCUIT 1205 (BK) FOR AN OPEN
z
Measure the resistance between exterior rear view mirror control
C527 pin 5, circuit 1205 (BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
GO to
A3 .
No
REPAIR the circuit.
TEST the system for
normal operation. A3 CHECK CIRCUIT 542 (YE) FOR AN OPEN Klj . 2 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST B: A SINGLE MIRROR IS INOPERATIVE z
Measure the resistance between passenger exterior rear view
mirror C622 pin C, circuit 542 (YE), harness side and exterior
rear view mirror control C527 pin 6, circuit 542 (YE), harness
side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new exterior
rear view mirror control.
REFER to
Switch —
Exterior Rear View
Mirror Control in this
section.
No
REPAIR the circuit.
TEST the system for
normal operation. Test Step Result / Action to
Take B1 CHECK THE COMMON FEED INPUT
z
Disconnect: Exterior Rear View Mirror C516 (Driver) C622
(Passenger).
z Disconnect the inoperative exterior rear view mirror C516 driver
side or C622 passenger side.
z Measure the voltage between driver exterior rear view mirror C516
pin C, circuit 542 (YE), harness side and ground; or between
passenger exterior rear view mirror C622 pin C, circuit 542 (YE),
harness side and ground.
z Select the inoperative side and actuate the exterior rear view
mirror control to the down position, then the right position.
z Are the voltages greater than 10 volts? Yes
GO to
B3 .
No
GO to B2 .
B2 CHECK CIRCUIT 542 (YE) FOR AN OPEN
z
Disconnect: Exterior Rear View Mirror Control C527.
z Measure the resistance between exterior rear view mirror control
C527 pin 6, circuit 542 (YE), harness side and driver exterior rear
view mirror C516 pin C, circuit 542 (YE), harness side; or between
exterior rear view mirror control C527 pin 6, circuit 542 (YE),
harness side and passenger exterior rear view mirror C622 pin C,
circuit 542 (YE), harness side. Yes
INSTALL a new
exterior rear view
mirror control.
REFER to
Switch —
Exterior Rear View
Mirror Control in this
section. TEST the
system for normal
operation. Klj . 3 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the resistance less than 5 ohms? No
REPAIR the circuit.
TEST the system for
normal operation.
B3 CHECK THE UP/DOWN INPUT
z
Measure the voltage between driver exterior rear view mirror C516
pin B, circuit 541(DB), harness side and ground; or between
passenger exterior rear view mirror C622 pin A, circuit 544 (VT),
harness side and ground.
z Actuate the exterior rear view mirror control to the up position.
z Are the voltages greater than 10 volts? Yes
GO to
B6 .
No
GO to B4 for driver
inoperative or GO to
B5 for passenger
inoperative. B4 CHECK CIRCUIT 541 (DB) FOR AN OPEN
z
Disconnect: Exterior Rear View Mirror Control C527.
z Measure the resistance between exterior rear view mirror control
C527 pin 3, circuit 541 (DB), harness side and driver exterior rear
view mirror C516 pin B, circuit 541 (DB), harness side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new
exterior rear view
mirror control.
REFER to
Switch —
Exterior Rear View
Mirror Control in this
section. TEST the
system for normal
operation.
No
REPAIR the circuit.
TEST the system for
normal operation. B5 CHECK CIRCUIT 544 (VT) FOR AN OPEN
z
Disconnect: Exterior Rear View Mirror Control C527.
z Measure the resistance between exterior rear view mirror control
C527 pin 7, circuit 544 (VT), harness side and passenger exterior
rear view mirror C622 pin A, circuit 544 (VT), harness side. Yes
INSTALL a new
exterior rear view
mirror control.
REFER to
Switch —
Exterior Rear View
Mirror Control in this
section. TEST the
system for normal Klj . 4 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the resistance less than 5 ohms? operation.
No
REPAIR the circuit.
TEST the system for
normal operation.
B6 CHECK THE LEFT/RIGHT INPUT
z
Measure the voltage between driver exterior rear view mirror C516
pin A, circuit 540 (RD), harness side and ground; or between
passenger exterior rear view mirror C622 pin B, circuit 543 (DG),
harness side and ground.
z Actuate the exterior rear view mirror control to the left position.
z Is the voltage greater than 10 volts? Yes
INSTALL a new
exterior rear view
mirror motor. REFER
to Mirror
— Motor in
this section. TEST
the system for normal
operation.
No
GO to B7 for driver
inoperative or GO to
B8 for passenger
inoperative. B7 CHECK CIRCUIT 540 (RD) FOR AN OPEN
z
Disconnect: Exterior Rear View Mirror Control C527.
z Measure the resistance between exterior rear view mirror control
C527 pin 4, circuit 540 (RD), harness side and driver exterior rear
view mirror C516 pin A, circuit 540 (RD), harness side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new
exterior rear view
mirror control.
REFER to
Switch —
Exterior Rear View
Mirror Control in this
section. TEST the
system for normal
operation.
No
REPAIR the circuit.
TEST the system for
normal operation. B8 CHECK CIRCUIT 543 (DG) FOR AN OPEN
z
Disconnect: Exterior Rear View Mirror Control C527.
z Measure the resistance between exterior rear view mirror control
C527 pin 8, circuit 543 (DG), harness side and passenger exterior
rear view mirror C622 pin B, circuit 543 (DG), harness side. Yes
INSTALL a new
exterior rear view
mirror control.
REFER to
Switch —
Exterior Rear View
Mirror Control in this
section. TEST the
system for normal Klj . 5 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST C: A SINGLE MIRROR DOES NOT FUNCTION WITH
SWITCH LOGIC z
Is the resistance less than 5 ohms? operation.
No
REPAIR the circuit.
TEST the system for
normal operation.
Test Step Result / Action to Take
C1 CHECK THE EXTERIOR REAR VIEW MIRROR LOGIC
z
Disconnect: Exterior Rear View MirrorC516 (Driver), or
C622 (Passenger).
z Disconnect the suspect exterior rear view mirror C516
driver or C622 passenger.
z Measure for voltage or resistance at the suspect exterior
rear view mirror harness side, while actuating the
exterior rear view mirror control according to the
following chart. Circuit Exterior rear view
mirror control
position Measure for
voltage or
resistance Driver
540
(RD) Left Greater than 10 volts
540
(RD) Right Less than 5 ohms
541
(DB) Up Greater than 10 volts
541
(DB) Down Less than 5 ohms
542
(YE) Left Less than 5 ohms
542
(YE) Right Greater than 10 volts
542
(YE) Up Less than 5 ohms
542
(YE) Down Greater than 10 volts
Exterior rear view
mirror control Measure for
voltage or Yes
INSTALL a new exterior rear
view mirror motor. REFER to
Mirror
— Motor in this section.
TEST the system for normal
operation.
No
GO to C2 . Klj . 6 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the circuit logic OK? Circuit position resistance
Passenger
543
(DG) Left Greater than 10 volts
543
(DG) Right Less than 5 ohms
544
(VT) Up Greater than 10 volts
544
(VT) Down Less than 5 ohms
542
(YE) Left Less than 5 ohms
542
(YE) Right Greater than 10 volts
542
(YE) Up Less than 5 ohms
542
(YE) Down Greater than 10 volts
C2 CHECK THE EXTERIOR REAR VIEW MIRROR
CONTROL z
Remove the exterior rear view mirror control. Leave the
harness connected.
z Measure for voltage or resistance at exterior rear view
mirror control C527 while actuating the exterior rear view
mirror control according to the following chart. Pin Circuit Exterior rear view
mirror control position Measure for
resistance or voltage 6 542
(YE) Left Less than 5 ohms
6 542
(YE) Right Greater than 10
volts 6 542
(YE) Up Less than 5 ohms
6 542
(YE) Down Greater than 10
volts Driver side selected
4 540
(RD) Left Greater than 10
volts 4 540
(RD) Right Less than 5 ohms
3 541
(DB) Up Greater than 10
volts 3 541
(DB) Down Less than 5 ohms
Passenger side selected
8 543 Left Greater than 10 Yes
REPAIR the circuits. TEST the
system for normal operation.
No
INSTALL a new exterior rear
view mirror control. REFER to
Switch
— Exterior Rear View
Mirror Control in this section.
TEST the system for normal
operation. Klj . 7 ba
82003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...