FORD SIERRA 1987 2.G SOHC Engines Workshop Manual

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual SIERRA 1987 2.G FORD FORD https://www.carmanualsonline.info/img/11/5462/w960_5462-0.png FORD SIERRA 1987 2.G SOHC Engines Workshop Manual
Trending: fuel pump, battery location, engine overheat, coolant level, oil capacity, clock, auxiliary battery location

Page 1 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual 1.3 litre engine
General
Engine type  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four-cylinder, in-line, single overhead camshaft
Firing order  . . .

Page 2 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual Crankshaft
Endfloat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.08 to 0.28 mm (0.003 to 0.011 in)
Main bearing running clearance . . . . . . .

Page 3 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual Inlet valve stem diameter:
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.025 to 8.043 mm
Oversize 0.2 . . . . . . . . . . . . . . . . . . . .

Page 4 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual 1.6 litre engine
General
Engine type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Four-cylinder, in-line, single overhead camshaft
Firing order . . . .

Page 5 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual 1.8 litre engine
General
Engine type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Four-cylinder, in line, single overhead camshaft
Firing order . . . .

Page 6 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual 2.0 litre engine
General
Engine type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..Four-cylinder, in-line, single overhead camshaft
Firing order . . . . .

Page 7 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual Piston ring end gap:
Top:
Up to 1985 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.038 to 0.048 mm
From 1985 . . . . . . . . . . . . . . . . . . . . . . . . .

Page 8 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual The following operations can be carried out
without removing the engine from the vehicle:
a)Removal and servicing of the cylinder
head
b)Removal of the camshaft after removal of
the cylinder head
c)Re

Page 9 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual 31Attach a suitable hoist to the engine lifting
brackets located at the front and rear of the
cylinder head, and carefully take the weight of
the engine. The engine should be supported
horizontally, i

Page 10 of 24

FORD SIERRA 1987 2.G SOHC Engines Workshop Manual where applicable disconnect the kickdown
cable from the carburettor/inlet manifold. 
2Note the location of the earth strap on the
rear inlet manifold stud, then remove the nut
and disconnect the strap
Page:   1-10 11-20 21-30 next >
Trending: ground clearance, coolant level, battery location, bolt pattern, radiator, clock, automatic transmission