airbag GEELY CK 2008 Owner's Manual

267(5) With reference to the figure below, insert thin probes into the current tester to check the conduction of
the terminals.V. KEY POINTS FOR SCRAPPING THE AIRBAG ASSEMBLYThe airbag shall be deployed according to the following procedures before scrapping the airbag assembly or
a vehicle installed with an airbag.
1. Scrapping of an airbag assembly prior to deployment
(1) Deploy inside a vehicle
1Park the vehicle in a flat area NOTICE
Never insert probe directly from the lower end of the connector.
NOTICE
The airbag shall be deployed before being scrapped.
The airbag shall be deployed outside the vehicle before being changed.
The airbag shall be deployed in the vicinity of a smoke detector since smoke will appear when the airbag is
deployed.
When being deployed, the airbag will create much noise. People nearby shall wear noise muffler to close
their ears. Avoid do the job within the residential areas.

2682Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery from
the vehicle.
3The airbag assembly shall be deployed according to the following procedures.
(2) Driver airbag assembly
1Remove the knee bolster.
2Remove the connector (yellow) that connecting the lower end of the clock spring with the wire harness
of the instrument panel (see the figure below).
3Tie two 6m plus wire harnesses for deployment to the adaptor wire harness of the airbag, and wrap the
connecting points with insulating tape for insulation. The other ends of the wire harness for deployment
are connected to each other (short circuited). Unexpected deployment resulted from static electricity
shall be prevented.
4From the yellow connector of the clock spring, lead the airbag adapter wire harnesses out of the vehicle
by means of the wire harnesses for deployment (see the figure below).
5To restrain the noise, close all the windows and doors and put on the vehicle cover. NOTICE
Work must be started 60s after the positive (+) and negative (-) terminal cables are detached from battery.NOTICE
Remove the connector of the clock spring from the wire harness of the instrument, the connector will be
short circuited automatically, which can avoid the possible serious accident resulted from the deployment of
the diver airbag assembly due to static electricity.
NOTICE
The glass will likely break up if there is crack. Vehicle covers shall be put on.

2696Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect them with the two terminals of the battery removed from the
vehicle and deploy the airbag (see the figure below).
7The deployed driver airbag assembly shall be scrapped according to the scrapping procedures.
(3) Deploy outside the vehicle
NOTICE:
Keep the airbag over 6m away from a obstacle or person and deploy the airbag in an open flat area.
1Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery
from the vehicle.
2The airbag assembly shall be deployed according to the following procedures.
(4) Driver airbag assembly
1Remove the driver airbag assembly from the vehicle.Vehicle CoverWire Harness
for DeploymentNOTICE
Make sure there is no man inside or near the vehicle and then carry out the operations.
After the driver airbag is deployed, the gas generator is of high temperature. Keep it for 30 minutes until it
gets cool for use.
If the driver airbag assembly cannot be deployed, discuss the problem with the local Geely service station.NOTICE
Work must be started 60s after removal of the battery.NOTICE
When the connector is not connected, the terminals of the driver airbag assembly will be short circuited
automatically, preventing the airbag from being deployed unexpectedly. If the airbag is deployed unexpectedly,
the deployed surface should face up. It should be kept on a flat surface without any other items on it.

2702Prepare two 6m plus wire harnesses for deployment, connect the other two ends to avoid unexpected
deployment in case of static electricity (see the figure below).
3Touch the body of the vehicle with hands for static electricity elimination.
NOTICE:
The above-mentioned procedures can prevent the unexpected deployment due to static electricity and shall
therefore be performed strictly.
4Cut off the wire harnesses of the driver airbag assembly and connect them with the two wire harnesses
for deployment, and make sure to wrap up the connecting location with insulating tape for insulation (see
the figure below).
5Install the unused bolts on to the inside bolt of the driver airbag assembly, and tie a thick wire securing the
wheel rim.
6Pass the deployment wire harness of the driver airbag assembly through an old tire with rim, and fix
upwards the driver airbag assembly by means of the wire connected to the bolts, etc (see the figure
below).Wire Harness
for DeploymentShort Circuit Location6m plusPassenger AirbagWire Harness
for DeploymentShort
Circuit
Location
Insulating TapeAirbag AssemblyWire Harness for Deployment

2717Put three old tires without hubs onto the tire used to fix the driver airbag assembly (see the figure below).
8Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect with the two terminals of the battery removed from the vehicle
and deploy the airbag (see the figure below).
9the deployed driver airbag assembly shall be scrapped according to the scrapping procedures.Wire Harness for DeploymentOld Wheels
without HubWire Harness
for DeploymentNOTICE
Make sure to deploy the driver airbag assembly when there is no person close by.After the driver airbag is deployed, the gas generator is of high temperature. Keep it for over 30 minutesuntil it gets cool for use

337(8) Make sure the warning light of the airbag system on for 6s and off.
If the warning light of the airbag system is not as specified, it means system fault. Check with the OBD (on-
board diagnostics).4.Rear Seat Belt Removal / InstallationWarning
Do not remove retractor.
(1) Fold rear seat back.
(2) Remove B pillar upper inside trim.
(3) Remove rear trunk partition.
(4) Remove bolt.
(5) Remove rear seat belt.
(6) The installation is in the reverse order of the removal.
5.Rear Seat Belt Buckle Removal / Installation
(1) Remove rear seat cushion.
(2) Remove the bolt.
(3) Remove rear seat belt buckle.
(4) The installation is in the reverse order of the removal.
6. Seat Belt Inspection
(1) Ensure correct installation of seat belt.
(2) Check the metal component of the seat belt for damage.
(3) If the vehicle has been vibrated during the accident, pull out the
seat belt from the retractor, observe by eye and touch the seat
belt with hand to ensure that there is no scratch (load limit retractor
does not operate).
zReplace the seat belt if it is not as specified in the technical specification.Seat BeltPullAnchorNickanchorage

3392. Instrument Panel Removal/Installation(1) Remove the airbag actuator at the driver side.
(2) Remove the intermediate instrument panel.
(3) Remove the audio device
(4) Remove A/C control mechanism.
(5) Remove in the order below in the figure.
(6) The installation is in the reverse order of the removal.
Torque: 18.6--25.5 N.m1 instrument panel w ire harness
2 instrument panel c ross member3instrument panel 123