%27 GEELY CK 2008 Owner's Guide

279 4 DTC 00283, 00285,00287, 00290 Like ly Cause s
[De s cription]
When there is recognized open
or short circuit in the sensor, this DTC is set.
[Hint]
The likely c ause ma y be the poor
c onne ction of the sensor, short circ uit in the coil
or wire ha rne ss, or fault in the se nsor signa l
proce ssing c irc uit in the ABS ECUz Ope n c irc uit in the se nsor c onne ctor or coil
z Short circuit in the sensor coil
z The se nsor c onne ctor or wire harne ss is short to
ground or powe r supply
z Fault in the sensor signal processing circuit in the
ABS ECURepair the connectorCheck the sensor on each wheelRemove the ABS ECU connector, check
whether the resistances among the following
terminals is within the specification?
Standard:
1.0~1.3K
LF: 1-2K
RF: 19-20K
LR: 5-6K
RR: 22-23K Check the corresponding sensor connectorDoes the fault reoccur?Check the wire harness between the ECU and
the sensor Refer to "Occasional Prob-
lem Service Key Points"Replace the ABS ECU
Abn.
Abn. Normal
Normal
Normal
Ye s Normal Ω,
Ω,
Ω,
Ω,
Ω,

327(IV) Rear trunk LidComponent View:
1.Rear trunk Lid Hinge Pin 2.Rear trunk Lid Hinge Retainer3.Rear trunk Lid Hinge Retainer
Mounting Nut4.Rear trunk Door Hinge Cushion 5.Rear trunk Lid Outer Panel And Reinforcement
Assembly 6.Geely Logo7.Rear License Plate Assembly8.Rear License Plate Assembly
Mounting Nut9.Rear trunk Lid Weatherstrip10.Rear trunk Lid inside Trim Board 11.Rear
trunk Lid Cushion12.Rear trunk Door Lock Cylinder Assembly 13.Rear trunk Lid inside Trim Board Clip
14.Rear trunk Lid Hinge Attaching Bolt 15.Rear trunk Door Lock Cable Assembly16.Rear
trunk Door Oil Filler Cable Assembly 17.Rear trunk Lid Hinge 18.Rear trunk Lid Spring

3336Install the headrest;
7Install the front seat with 4 tightening bolts. Torque: 14.72~23.52N.m.3.Adjust1The seat can adjust tilt angle forward in torque 2° x 5=10°;
Adjust backwards 2° x 27=54°;
2The seat assembly slides forwards 15mm x 4=60mm in torque 15N.m;
Slide backwards 15mm x 10=150mm;
3The headrest can be adjusted in 3 positions in height.Rear Seat1.Rear seat back
1Removal
a. Lift the rear seat back lock handle upwards. Turn seat back down forwards. Remove 4 set bolts.
Remove seat backassembly from the vehicle;
b. Remove seat back lock handle and handle seat;Install Front and Rear Seat Snap RingInstall Headrest SupportTrack Assembly Adjuster AssemblyInstall Adjuster and Track AssemblyAssemble the Seatback and Cushion

3362. RetractorThe retractor is pre-tensioner. The retractor will pre-tension the seat belt when something emergency hap-
pens to prevent passengers from being hurt. It can sense the vehicle acceleration and the acceleration of the
belt being pulled out.
The retractor belt can be pull out and drawn back freely. It will not be locked at 12° around the safety
position, but locked at over 27°. The passenger can move in small area. The pre-tensioner will transmit within
5ms~10ms when something emergency happens to tension and lock the belt.Notice:1 . Check the product for damage, crack and rust before installation.
2 . Put the retractor vertically and the belt can be pulled out. Check if the belt can be pulled out
and around. Check if the retractor works.
3 . When installing the pretensioned seat belt, check the transmittor head pin for slant and rust.
The transmitter in the pretensioned seat belt can be used for 15 years after installation.
4 . Check if the belt buckle and the attachment matches the connecting mode of the to-be-installed
vehicle module. Check if the opening of the buckle is flexible.
5 . See if the screw thread of the nut welded on the cover is clear when installing the bolt. Assemble
the bolt after clearing the welding residue if there is any.
6. When the retractor belt is pulled out, there should be no obstacles around the belt (such as,
wire harness ect) , Remove the obstacles and make sure the retractor and the belt will not be
scratched.
3.Front seat belt removal/installation
Warning:
Do not remove retractor.(1) Turn the ignition switch to LOCK.
(2) Disconnect the negative (--) terminal cable from the battery
for 1min.
(3) Remove B- pillar lower frame.
(4) Pry the seat belt which is used to install the tension wheal.
Use a screwdriver to pry off the stop plate of the seat
belt connector with tensioner.
(5) Disconnect the seat belt connector with tensioner.
Remove 2 set bolts on the hang ring and remove the hang
ring.
(6) Remove two set bolts in the retractor and remove the
front seat belt.
(7) The installation is in the reverse order of the removal.Stop PlateBoltFront Seat BeltScrew
BoltLid

347(XIII) Carpet and Heat InsulatorCarpet and Heat Insulator Diagram
Carpet and Heat Insulator Diagram
1. Carpet 2. Cowl Lower Sound Insulator 3. Cowl Upper Sound Insulator 4 . Cowl Outer
Panel Heat Insulator 5. Foot Pedal 6. Cross Pan Head Screw 7. Floor Sound Insulator
1. Removal
1Remove the front and rear seats, left front door sill, right front door sill, right B pillar lower inside trim, left
B pillar lower inside trim, right rear door sill, left rear door sill, front and rear part of the auxiliary console;
2Remove the cross pan head screw and remove the foot pedal.
3Remove carpet and cowl lower sound insulator, cowl upper sound insulator, cowl outer panel heat insulator.
2. Installation
1Install the accelerator pedal assembly, brake and clutch pedal assembly, parking brake control mechanism
assembly onto the vehicle body;
2Install the carpet to the corresponding hole. Install both sides of the carpet under the left front door sill,
right front door sill, right B pillar lower inside trim, left B pillar lower inside trim, right rear door sill, left
rear door sill.1 27 3
4
65