power steering GEELY CK 2008 Owner's Guide
[x] Cancel search | Manufacturer: GEELY, Model Year: 2008, Model line: CK, Model: GEELY CK 2008Pages: 392, PDF Size: 38.86 MB
Page 265 of 392

2581Turn the ignition switch to LOCK.
2Loosen the negative terminal cable from the battery and wait for over 1 minute.
3Remove the glove box.
4Loosen the passenger airbag assembly connectors.
5Is the connector of the passenger airbag assembly normal?
Normal: [DTC of present trouble]
Continue with next step.
[DTC of past trouble]
Continue with next step.
Abnormal: replace the wire harness.
(3) Ascertain the trouble exists in passenger airbag assembly or other part
1Connect a new assembly to terminals A and B of the connector of passenger airbag assembly.
2Connect the negative (-) terminal cable of the battery.
3Turn the ignition switch ON.
4Any DTC displayed? Can it be cleared?
No: continue with next step.
Yes: replace passenger airbag assembly
See SRS- Passenger Airbag Assembly, Removal & Installation.
(4) Check the wire harness between passenger airbag assembly and SRS ECU
1Turn the ignition switch to LOCK.
2Loosen the negative (-) terminal cable from the battery and wait for over 1 minute.
3Remove steering column hood.
4Loosen the connector of the clock spring.
5Loosen the connectors of driver and passenger airbag assemblies.
6Remove left trim plate.
7Loosen all the SRS unit connectors.
8Check the circuit between the connector terminals of the SRS ECU and that of passenger airbag assembly
and the circuit between the connector terminal of the SRS unit and that of passenger airbag assembly for
the following:
yGround.
yShort circuit with power source.
yOpen circuit.
9Are the above-mentioned wire harnesses normal?
Normal: completion of trouble diagnosis.
Abnormal: replace the related wire harness.
Page 266 of 392

259III. DIAGNOSIS OF CRASHED VEHICLEsWhether the SRS is deployed or not, the checking and maintenance of the crashed vehicle shall be carried
out according to the following procedures.
1. Check the diagnostic signal of ECU
(1) Connect the check connector of the Hi-DS T Scan Meter.
(2) Read out the diagnostic results from Hi-DS T Scan Meter.
2. Repair procedures
(1) When the SRS is deployed, the following parts shall be renewed.
1Passenger airbag assembly.
2ECU.
3Driver airbag assembly.
Check the following parts, if abnormal, replace with new ones.
1Clock spring.
2Steering wheel, steering column and steering lower shaft
component.
The installation status of driver airbag assembly in relation to steering wheel.
1Check and see if there is abnormal noise in the steering wheel, the action of the same is good,
or the clearance is normal.
2Check the union joint of the wire harness for damage and the terminal for distortion.
3. ECU
(1) Check the brackets of the ECU Case for recess, crack, distortion, etc.
(2) Check the union joint for damage and terminal for distortion.
(3) Check the installation status of he ECU brackets
1Check the hood for recess, crack, distortion, etc.
2Check the union joint for damage, terminal for distortion
and wire harness for seizure.
3Check the case of the gas generator for recess,
crack and distortion.NOTICE
Due to shock, when the battery power
supply is insufficient, the scan Meter
cannot communicate with ECU, the
instrument panel wire harness shall be
checked and maintained or external
power source shall be used.
Page 327 of 392

320(III) Front inside trim613
7 Front door power window switc 14Elec tric outs ide rear view mirr or 5 Instrument panel end shield 12 Auxiliary console assembly 3 A/C panel assembl 10
411 1 A- pillar in s ide t r im 8
29
Low er en d s hield as s em b ly
Front row seat Front door insdie trim
Instrument panel assembly
Glove c ompartment as s embly
Steering column coverFront door sill inside trim
Front end of auxiliary c onsole