brake GEELY CK 2008 Repair Manual

273IV. DTC Display Method
V. HCU DiagnosisUse the scan meter to diagnose the Hydraulic Control Unit (HCU), select the "3 HCU diagnosis" in the
options and perform the following procedures.
* Perform the above step 2 - 8 test for each wheel in the following order LF RF LR RR.
* If the result of some one of the above steps is different from the normal result, it indicates that the
corresponding element fails the normal operation, please check the corresponding element.
* You can use “ESC” button to end the test to return the function menu in any place in the screen where
there is “return” displayed to return to the function menu.Code Displa ye d
Ne ve r ha ppe ne d be fore No DTC
Happened before Occasional DTC
Ne ve r ha ppe ne d be fore Non-occ a sional DTC
Happened beforeOccasional DTC and Non-
occasional DTC System P roblem
The re is no proble m current ABS
Warning Light does not light up）
The problem still e xists（
ABS
Wa rning Light goe s on）Step Action Screen Display Normal Result
1 HCU dia gnosis – hydra ulic pump te st P ump motor operate s
2 LF Wheel——Depress the brake pedal
3LF Whe e l—— norma lly ope n va lve
ope n, norma lly c losed va lve c lose d,
wheel locked？Wheel locked
4LF Whe e l—— norma lly ope n va lve
closed, normally closed valve closed,
wheel locked？Wheel locked
5LF Wheel — — normally open valve
close d, norma lly close d va lve open,
wheel can rotate freelyWheel can rotate freely, the
pe da l re bound, the c ylinde r
motor ope ra ting noise is a udible
6LF Whe e l—— norma lly ope n va lve
closed, normally closed valve closed,
wheel can rotate freelyWheel can rotate freely
7LF Wheel — — normally open valve
ope n, normally c lose d va lve close d,
wheel locked？Wheel locked, the pedal sag
slightly
8Release the brake
pe dal De pre ss and hold
the brake pedal→→→

274VI. Troubleshooting Quick Index
VII. Non-DTC Problem Inspection Table IndexDTC Fault Description Diagnosis ResultInspection
Table No.Reference
Page
65535 ECU Da ma ge d
1276 ABS hydraulic pump Motor c a n not ope ra te 1 275
283 LF Whe e l Sensor 276
285 RF Whee l Se nsor 277
290 LR Whe el Se nsor 278
287 RR Whe e l Se nsor
1044 ABS progra mming e rror 5 279
668 P ower supply te rmina l 30 6 280
1130 Abnorma l ABS ope ra tion Signa l is not as spe cifie d 7 281Electrical or mechanicalfault2,3,4Inspection
Table No.Reference
Page
1282
2283
The bra ke forc e on both s ide s is not uniformThe brake force is insufficientABS operate s whe n the bra ke pe dal is slightly
depre ssed（vehicle is stationary）
ABS operate s whe n the bra ke pe dal is slightly
depre ssed（ve hic le is driving）
Whe n the ABS ope ra tes, the bra ke pe dal vibrate s
severely
4285
5286
6287 No DTC output（
failure in communicating with the scan meter） Fault Status
Turn the ignition switc h to “ON” (With engine off), ABS Wa rning
Light doe s not go on
Afte r the e ngine is sta rte d, the wa rning light doe s not go off
ABS
abnormal284 3
Brake peda l stroke is exc e ssive ly long
You ne ed to he a vily depre ss the brake peda l

275VIII. ABS ECU Connector Pin LayoutABS ECU Connector (End Views)
Electrical Wiring DiagramCombination MeterABS Warning Light
Drive ModuleABS ECU
ABS RR Wheel Sensor
ABS LR Wheel Sensor ABS RF Wheel Sensor
ABS LF Wheel Sensor
Brake Lamp Switch

286 4 Exce s s ive ly long brak e pe dal s trok e Lik e ly Caus e s
[De s cription]
Visually inspect whether there
is leakage or mechanical fault. Use bleeding
method to check whether there is air in the
system. Use the HCU function of the scan
meter to test whether the normally-closed valve
is le a king.z Brake fluid leakage
z Air in the system
z Brake disc severely worn
z B r a ke f luid le ve l s w it c h f a ult yTighten the pipe connector as
specifiedVisually inspect whether the hydraulic pipe connector is
leaking Check the brake disc wearReplace the brake disc Abn. Ok Abn. Check the brake fluid level switchOk Bleed and checkOk Use the scan meter HCU to diagnose and check the nor-
mally-closed valve sealOkReplace the brake fluid level
switch Abn.Re-bleed the system Abn.Replace the HCU Abn.

291IV. ABS Operation Inspection1. Check the Wheel Speed Sensor Output Voltage
1Check whether the clearance between the wheel speed sensor and the ring gear is within the specification
For front wheel standard value, refer to "Front Wheel Sensor Installation Drawing"
For rear wheel standard value, refer to "Rear Wheel Sensor Installation Drawing"
3Jack up the wheel and release the manual brake
2Remove the ABS wire harness, measure at the wire harness connector
4Rotate the wheel at the speed of 1/2 turn/second, and use the multimeter or oscilloscope to measure the
output voltage
Terminal 1-2
Terminal 19-20
Terminal 5-6
Terminal 22-23
Output Voltage
zWhen use the multimeter to measure
For front wheel, refer to "Front Wheel Sensor Drawing".
For rear wheel, refer to "Rear Wheel Sensor Drawing".
zWhen use the oscilloscope to measure
For front wheel, refer to the related standard.
For rear wheel, refer to the related standard.
5The fact that the output voltage is not within the above range may result from the following causes:
zExcessive clearance between the sensor and the ring gear.
zSensor fault.
zCheck the sensor resistance£¨1.0 - 1.3k¦¸£©.
zSelect the 4 points on the ring gear to check the clearance (ring gear distortion) between the ring
gear and the wheel speed sensor.
2.Check the Hydraulic Control Unit (HCU).
1Jack up the vehicle, make sure the wheel can rotate freely.
2Release the manual brake.
3Turn the ignition switch to ON after connecting the scan meter, do not start the engine this time.
4Refer to the HCU Diagnosis for inspection.
Note: when connecting or removing the scan meter, the ignition switch must be turned to OFF.

292Section 3 Removal and InstallationI.Precautions for Removal1. Use the scan meter to locate the fault causes before proceeding to service.
2. wipe the surface clean with the cleaning agent without mineral oil before service; be careful to keep it
clean during service, only the lint-free cloth can be used to wipe the removed parts.
3. Only the original spare part can be used, and the package of the new spare part shall not be removed until
the installation.
4. Return liquid pump motor and the HCU is a type of integral structure and can not be separated.
5. When the system is opened, do not use compressed air or move the vehicle.
6. Use proper plug to clog each hydraulic outlet as soon as the ABS assembly is removed.
7. Remove other components that may interfere.
8. Please use the DOT 4 brake fluid, do not use the mineral oil.
9. Use the brake fluid to immerse the seal and the O ring, do not use the engine oil or brake grease.
10. After service, check the regular brake system and ABS brake function for normal and reliable operation.
11. Check all hydraulic pipe union for leakage.II. HECU Removal1. Turn off the ignition switch and disconnect the battery negative ground cable.
2. Remove the wire connector from the ABS HECU assembly.
3. Depress the brake pedal >60mm and hold it with the pedal retainer to close the master cylinder center
valve so that the brake fluid will not flow out from the outlet when the system is opened.
4. Put a clean cushion under the hydraulic regulator.
5. Remove the brake pipe (A, B) on the HCU connected to the master cylinder and place the mark, then
use a plug to clog the outlet immediately.
6. Remove the brake fluid pipe(1-4) leading to the wheels, then use a plug to clog the outlet immediately.
7. Remove the nut attaching the HECU to the bracket.

2938. Remove the whole HECU from the bracket.
ABS HECU Assembly
ABS HECU Brake Pipe Removal Schematic

295V. ABS Assembly ReinstallationNote: the plug of the ABS assembly hydraulic outlet can only be removed after the brake pipe is
installed, lest the foreign object will enter the brake system.1. Install the ABS assembly to the bracket, tighten the torque: 20+4Nm.
2. Remove the plug of the hydraulic outlet, installed the brake pipe. Make sure that the brake pipe is
correctly installed.
3. Install the brake pipe connected to the master cylinder.
4. The brake pipe torque is 12+4Nm (M10 x 1) and 15+3Nm (M12 x 1).
5. Fill the new brake fluid into the reservoir until the liquid level reach the MAX and bleed it as specified.
6. With the ignition switch ON, ABS Warning Light must goes on for 1.7 seconds then goes off.
7. Clear the DTC memory, check if there is DTC again.
8. Drive the vehicle to confirm the ABS function (you must feel that the pedal rebound).VI. ECU ProgramNote: when replacing the HECU or ECU, you shall program the new ECU, otherwise the ABS
Warning Light flashes and the system can not operate normally.Use the scan meter to program the ECU based on the following procedure:Connect the scan meter with the diagnostic interfaceSelect function 07, Press OK button to confirmEnter code 01901 and Press OK button to confirmSelect function 07, Press OK button to confirm, quit the diagnosticEnd

296VII. Fill the liquid and bleedAfter replacing the HECU, bleed the second HECU circuit in addition to the filling and bleeding of the regular
brake system. Use the scan meter to perform the following procedure:Fill the fluid and bleed based on the regular brake system
until there is no air bubble in the transparent hoseConnect the scan meter with the diagnostic interfaceSelect function 04, Press OK button to confirmDepress the brake pedal and keep the hydraulic cylinder pushrod reboundRelease the brake pedal, loosen the left and right brake caliperbleeder screw, press "" buttonDepress the brake pedal 10 times, tighten the left and right
brake caliper bleeder screw, press "" buttonRepeat the above I II III steps 7 times and press "" buttonThe screen display the end of the bleed, press
"" button to return to "function selection" menuSelect function 06, Press OK button to confirm, quit the
diagnostic modeEnd →↑
↑
↑

347(XIII) Carpet and Heat InsulatorCarpet and Heat Insulator Diagram
Carpet and Heat Insulator Diagram
1. Carpet 2. Cowl Lower Sound Insulator 3. Cowl Upper Sound Insulator 4 . Cowl Outer
Panel Heat Insulator 5. Foot Pedal 6. Cross Pan Head Screw 7. Floor Sound Insulator
1. Removal
1Remove the front and rear seats, left front door sill, right front door sill, right B pillar lower inside trim, left
B pillar lower inside trim, right rear door sill, left rear door sill, front and rear part of the auxiliary console;
2Remove the cross pan head screw and remove the foot pedal.
3Remove carpet and cowl lower sound insulator, cowl upper sound insulator, cowl outer panel heat insulator.
2. Installation
1Install the accelerator pedal assembly, brake and clutch pedal assembly, parking brake control mechanism
assembly onto the vehicle body;
2Install the carpet to the corresponding hole. Install both sides of the carpet under the left front door sill,
right front door sill, right B pillar lower inside trim, left B pillar lower inside trim, right rear door sill, left
rear door sill.1 27 3
4
65