mirror GEELY CK 2008 Workshop Manual

Section 3 Removal & Installation................................................................................... 262Chapter 8 MK-20 ABS System........................................................................ 2 7 2Section 1 ABS Diagnosis ................................................................................................. 272
Section 2 ABS System Check .......................................................................................... 276
Section 3 Removal and Installation................................................................................. 292Part IV Air Conditioner and Inside & Outside Trim ......................297Chapter 1 A/C System...................................................................................... 2 9 7Section 1 The Structure & Working Principle of Refrigeration System...............................297
Section 2 Heating System ................................................................................................ 299
Section 3 A/C controlling system.................................................................................... 302
Section 4 Service Caution & Notice................................................................................ 304
Section 5 The Refrigeration System Operation Procedure..............................................305
Section 6 Basic System .................................................................................................... 308
Section 7 A/C System Faults Check & Troubleshooting................................................ 313Chapter 2 Inside & outside Trim and Accessory................................................318Section 1 Configuration Index............................................................................................318(I) Outside Trim And Front Accessory.................................................................................318
(II) Outside Trim and Rear Accessory.................................................................................319
(III) Front inside trim..........................................................................................................320
(IV) Rear inside trim ............................................................................................................321Section 2 Inside & Outside Trim and Accessories Removal and Installation.......................322(I) Front Bumper..................................................................................................................322
(II) Engine Hood.................................................................................................................324
(III) Outside Rear View Mirror
(IV) Rear trunk Lid...............................................................................................................327
(V) Rear Bumper...................................................................................................................329
(VI) Seat Removal, Installation and Adjustment...................................................................331
(VII) Seat Belt.....................................................................................................................335
(VIII) Instrument panel and auxiliary console.....................................................................338
(IX) A pillar inside trim and front door sill ............................................................................343
(X) B pillar inside trim........................................................................................................344
(XI) Cpillar inside trim and rear door sill.............................................................................345
(XII) Roof inside trim
(XIII) Carpet and Heat Insulator.............................................................................................347 ...............................................................................................326
...........................................................................................................346

240II. Radio assembly1. Remove the intermediate instrument panel (See interior trim)
2. Remove the radio assembly
1Remove 4 bolts
2Disconnect connectorIII. Front speaker assembly1. Remove front outside rear view mirror cover
2. Remove door handle
3. Remove the front door power window switch assembly
4. Remove the front door inside trim plate assembly
5. Remove the front door five-inch speaker assembly
1Disconnect connector
2Remove 4 self tapping screw and speaker assemblyIV. Tweeter speaker assembly1. Remove front outside rear view mirror cover
2. Remove tweeter speaker assembly
1 Disconnect connector
2Remove 2 self tapping screw and speaker assemblyV. Rear speaker assembly1. Remove rear speaker baffle
2. Remove rear speaker assembly
1 Disconnect connector
2Remove 4 self tapping screw and rear speaker assemblyVI. Remove antenna cable1. Remove the roof interior trim
2. Remove A-pillar trim plate
3. Disconnect connector
4. Remove instrument panel
5. Remove 4 clips and antenna cable

318Chapter 2 Inside & outside Trim and AccessorySection 1 Configuration Index(I) Outside Trim And Front Accessory1 Door handle 6 Windshield
Front fender
(See the engine hood adjustment)
Front bumper
(See front bumper
r em o v a l/ in s t allat io n )
The engine hood
(See the engine hood
r em o v a l/ in s t a llat io n )
Elec tric outs ide rear view mirror
(See elec tric outs ide rear view
m ir r o r r em o v a l/ in s t allat io n ) 5 Co w l v e n t g r ille 1 0Front mudguard skirt
4 9 Fuel fill port cap 2 Ra d ia t o r g r ill a s s em b ly 7
38

321(IV) Rear inside trim1 Inner rear view mirror 10 Rear doorinside trim
2 I n t e r io r la m p 1 1 C- p illar u p p er in s id e t r im
Rear seat belt buckle
(See rear seat belt buckle
r e m o v al/ in s t allat io n ) r ear t r u n k
in s id e t r im
4 Sun visor 13 Rear trunk low er trim c over
5 B- p illar u p p er in s id e t r im 1 4 Lo w er r ea r t r im a s s em b ly
Rear s eat
( S ee r ea r s eat r em o v al/ in s t allat io n )
Fr ont s eat belt Rear s eat belt
( See f ront s eat belt
r em o v a l/ in s t a lla t io n )( See Rear s eat belt
r em o v a l/ in s t allat io n )
( See s eat belt ins pec tion) (See s eat belt ins pec tion)
8 B- p illar lo w er in s id e t r im 1 7 Rea r d o o r s ill in s id e t r im
9 Safe handle 18 Carpet & sound insulator 716 3 A- p illar in s id e t r im 1 2
6 Roof ins ide trim 15

326(III) Outside Rear View MirrorAttach the outside rear view mirror to the left and right doors. Integrate the outside rear view mirror with the
body smoothly using specially designed rubber bushing to make it a whole. The forward and rearward folding
of the rear view mirror will not be affected after being knocked. It is also a major way to reduce the whole
vehicle's air resistance coefficient.
Attach the lens to the plate with double sided adhesive tape. The plate is connected to the rear view mirror
case with the ball hinge to prevent fragment from splashing when it is broken, which may result in injury and
it is convenient to replace the broken lens. Pry the plate from the ball socket with the tool when the lens is
broken for replacement and press the new one into the ball socket. The case overturn force is designed to be
30N, enabling it liable to overturn when impacted by person or object and hence reducing the mutual damage.
The adjust handle of the outside rear view mirror is designed to be built in the vehicle to facilitate the
operator's direction adjustment. The optional flat mirror is generally selected for driver side to ensure the
sense of reality and distance. Spherical mirror is used for front passenger side to enlarge the rear field of
vision. In addition, outside rear view mirror has also the feature of electrical heating and defogging.
Notice
When folding the outside rear view mirror, be careful not to put your finger between the outside
rear view mirror and the mirror foot to avoid being crushed!Replace the Rear View MirrorRemoval
1. Remove battery negative cable.
2. Remove the inside trim.
3. Disconnect electric outside rear view mirror connector.
4. Remove screw and outside rear view mirror retaining clip.
5. Remove electric outside rear view mirror.
6. The installation is in the reverse order of the removal.Installation1. Position the rear view mirror on the door
2. Tighten the screw from left lower side screw clockwise
Tighten
Tighten the outer rear view mirror screw to 1.5 N.M¡«2 N.M
3. Install rear view mirror inside trim cover
4. Install rear view mirror inner adjust handle