wheel bolts GEELY FC 2008 User Guide

Front suspension - Front stabilizer barFront stabilizer barOverhaul1. Remove dust cap inside steering column (see Page 194).
2. Separate steering sliding shaft assembly (see Page 205)
3. Remove front wheels.
4. Remove right engine bottom shield.
5. Remove left engine bottom shield.
6. Remove front left stabilizer link assembly
[64000097].Remove 2 nuts and take down stabilizer link.
Hint: if ball joint rotates with nuts, please fix bolts with
hexagonal wrench (6mm).7. Remove front right stabilizer link assembly
[64000097].Hint: the removal procedures of right side are the same
as that of left side.8. Check front left stabilizer link assembly.(a) As shown in the diagram, before installing nuts, shake joint
bolts forward and backward 5 times.
(b) Shake nuts continuously with torque wrench at the speed
of one circle per 24 s, and then read out torque value at
the 5th circle.
Rotating torque: 0.05~1.0 N.m9. Separate left side transversal lever assembly (see Page 113).
10. Separate right side transversal lever assembly (see Page 113).
11. Separate oil pipe assembly (see Page 205).
12. Separate steering gear oil return pipe (see Page 205).
13. Separate lower left control arm assembly [64000091] (see Page 94).
14. Separate lower right control arm assembly [64000092] (see Page 94).
15. Remove sub frame assembly [64000087] (see Page 205).
96

16. Remove front stabilizer bar.(a) Remove 4 bolts, bracket and bush.
(b) Remove stabilizer bar.17. Install front stabilizer bar.(a) Install bracket and bush with 4 bolts.
Hint: install bush to bush stop ring outside of
stabilizer bar.18. Install sub frame assembly [64000087]
(see Page 205).Front suspension - Front stabilizer bar19. Connect lower left control arm assembly [64000091] (see Page 94).
20. Connect lower right control arm assembly [64000092] (see Page 94).
21. Connect power steering oil pipe assembly (see Page 205).
22. Connect steering oil return pipe (see Page 205).
23. Connect left side transversal lever assembly (see Page 113).
24. Connect right side transversal lever assembly (see Page 113).
25. Install front left stabilizer link assembly
[64000097].(a) Install front stabilizer link with 2 nuts.
Torque: 745 N.m
Hint: if ball joint rotates with nuts, please fix bolts with
hexagonal wrench (6mm).26. Install front right stabilizer link assembly
[64000097].Hint: the installation procedures of right side are the
same as that of left side.27. Install right engine bottom shield.
28. Install left engine bottom shield.
29. Install front wheels.Torque: 10310 N.m97Rear
side Bush stop ring Outside

Front suspension - Front left lower control arm ball joint assemblyFront left lower control arm ball joint assemblyReplacementHint: the replacement procedures of right side are the same as that of left side.1. Remove front wheels.
2. Remove front left shaft hub nuts (see Page 123).
3. Disassemble front left speed sensor assembly [67000020] (see Page 123).
4. Disassemble front left brake wheel pump assembly and brake block (see Page 141).
5. Remove front left brake assembly [64000134] (see Page 141).
6. Disassemble left side transversal lever assembly (see Page 123).
7. Disassemble lower left control arm assembly [64000091] (see Page 94).
8. Remove front left shaft hub assembly (see Page 123).
9. Remove lower left control arm ball joint assembly [64000093] (see Page 123).
10. Check lower left control arm ball joint assembly [64000093].(a) As shown in the diagram, before installing nuts, shake
joint bolts forward and backward 5 times.
(b) Shake nuts continuously with torque wrench at the
speed of one circle per 2~4 s, and then read out torque
value at the 5th circle.
Rotating torque: 1.0~4.9 N.m11. Install lower left control arm ball joint assembly
[64000093] (see Page 123).
12. Install front left shaft hub assembly
(see Page 123).
13. Install lower left control arm assembly [64000091] (see Page 123).
14. Install left side transversal lever assembly (see Page 123).
15. Install front left brake assembly [64000134] (see Page 141).
16. Install front left brake wheel pump assembly and brake block (see Page 141).
17. Install front shaft hub nuts (see Page 123).
18. Install front wheels.Torque: 10310 N.m19. Check and adjust front wheel alignment (see Page 87).
20. Check ABS sensor signal.99

Rear strut assemblyOverhaulHint: the following overhaul procedures only aim at left side (LH), and the overhaul procedures
of another side (RH) are the same as LH.
1. Remove rear wheels.2. Remove rear left seat backrest assembly [68010078] (see Page 352).
3. Remove spare tire trim cover assembly.
4. Remove rear floor trim
5. Remove trunk left garnish [68000112].
6. Remove rear left strut assembly [64000098].(a) Support rear shaft with a jack.
(b) Remove 2 nuts and bolts.Rear suspension - Rear strut assembly(c) Remove nuts, gasket and rear strut assembly.7. Remove rear left strut assembly [64000098].(a) Compress helical spring with special tool.
Note: do not use pneumatic wrench, or the special tool
will be damaged.Wooden
block
Special tool102

(j) Fix piston rod with a hexagonal wrench of 6mm, and tighten
nuts.
Torque: .m10. Temporarily lock up rear strut assembly.(a) Install rear strut, and temporarily lock up nuts and gasket.
(b) Install 2 nuts and bolts.
Torque: 11. Install real left seat backrest assembly [68010078].
12. Align suspension.(a) Lay down vehicle from the lift after installing rear wheels.
Torque: (b) Align suspension components by means of lifting
vehicle several times.13. Completely lock up rear strut assembly.Completely tighten nuts.
Torque:.m14. Check rear wheel alignment (see Page 101).Handling1. Handle rear left strut assembly [64000098].(a) Completely pull out shock absorber piston rod.
(b) As shown in the diagram, drill a small hole on cylinder body
between two lines with electric drill to make inside gas flow
out.
Notesz

Iron chip may fly out during drilling, please be care-
ful in operating. z The gas is colorless, odorless and nontoxic.Rear suspension - Rear strut assembly104

Rear suspension - Rear shaft assemblyRear shaft assemblyOverhaul1. Remove rear wheels.
2. Disassemble rear left brake caliper assembly
(see Page 144).
3. Disassemble rear right brake caliper assembly
(see Page 144).
4. Disassemble rear wheel speed sensor wire harness(a) Uncouple sensor joint.
(b) Remove 2 bolts and disassemble wire harness retaining
clip.5. Remove rear left/right brake assembly [64000137/
64000139].(See Page 144)6. Remove rear stabilizer bar assembly (see Page 105).
7. Disassemble rear left/right strut assembly
(see Page 102).
8. Remove rear shaft assembly [64000120].(a) Support rear shaft assembly with a jack.
(b) Remove 2 bolts, gasket and rear shaft.Special
tool106

14. Temporarily lock up rear left strut assembly.(a) Install rear left strut and gasket, and temporarily lock
up nuts.
(b) Perform to another side in the same way.15. Install rear stabilizer bar assembly (see Page 105).
16. Install rear left/right brake assembly [64000137/64000139] (see Page 144).
17. Install rear wheel speed sensor wire harness.Install wire harness and parking brake cable with 2 bolts and retaining clips.
Torque: (A) 5.4 N.m
(B) 5.0 N.mRear suspension - Rear shaft assembly108 18. Install rear left brake caliper assembly
(see Page 144).
19. Install rear right brake caliper assembly
(see Page 144).
20. Align suspension.(a) Lay down vehicle from the lift after installing rear wheels.
Torque: (b) Align suspension components by means of lifting ve-
hicle with a jack several times.21. Completely lock up rear shaft assembly
[64000120].(a) Completely tighten bolts and pull on open pin.
Torque: m
(b) Perform to another side in the same way.22. Completely lock up rear left strut assembly.(a) Completely tighten bolts.
Torque: m
(b) Perform to another side in the same way.23. Check rear wheel alignment (see Page 101).
24. Check ABS sensor signal.

Drive shaft--Front drive shaft35. Assemble left lower control arm assembly [64000091](a) Assemble lower ball joint on lower suspension arm with the
bolts and screw caps.
Torque: 142 ± 10 N
⋅ ⋅⋅ ⋅
⋅m36. Assemble left transversal lever assembly.(a) Assemble transversal lever terminal to steering knuckle with
screw cap.
Torque: 49 ± 5 N
⋅ ⋅⋅ ⋅
⋅m
(b) Assemble new cotter pin.
Note: if hole position of cotter pin could not make a
line, lock the screw cap for 60.37. Assemble speed sensor assembly of left front
wheels (equipping with ABS) [67000020](a) Assemble speed sensor absorber with bolts.
Torque: 49 ± 5 N
⋅ ⋅⋅ ⋅
⋅m
(b) Assemble speed sensor on the steering knuckle with bolts.
Torque: 8 N
⋅ ⋅⋅ ⋅
⋅m
Note:zDo not damage speed sensor.zPrevent it from contacting with sundries.zWhen assembling the sensor, the wiring harness
of sensor could not bend.38. Assemble fixing nuts of drive shaft [68000083](a) Assemble fixing nuts.
Torque: 216 ± 15 N
⋅ ⋅⋅ ⋅
⋅m
(b) Use chisel and hammer to knock the fixing nuts concave
and fix them.39. Assemble front wheels.Torque: 103 ± 10 N
⋅ ⋅⋅ ⋅
⋅m40. Add the oil in gearbox.
41. Check and adjust the oil in gearbox.
42. Check and adjust wheel alignment (referring to page
87)
43. Check the ABS speed sensor (equipping with ABS).
44. Test on road.
122

Driveshaft--Left front shaft hub assemblyLeft front shaft hub assemblyChangeHint: changing procedure for right side is same as the left
side.1. Disassemble front wheels
2. Disassemble fixing nuts of left front drive shaft
[64000083](a) Use special tool and hammer to unclench concave part of
fixing nuts.
(b) Disassemble fixing nuts.3. Disassemble speed sensor assembly of left front
wheel [67000020](a) Disassemble the bolts, then disassemble the wiring har-
ness of sensor and brake hose.
(b) Disassemble the bolts, then disassemble speed sensor
from steering knuckle.4. Disassemble left front brake caliper assemblyDisassemble two bolts to disassemble brake caliper bracket.Special
tool123

Drive shaft--Left front shaft hub assemblyUse centimeter to check the axial clearance of shaft hub center.
Maximal value: 0.05 mm
If axial clearance exceeds the maximal value, it is necessary
to change the bearing.28. Check the terminal face run-out of shaft hub.Use centimeter to check the terminal run-out of exterior sur-
face of shaft hub.
Maximal value: 0.05 mm
If terminal run-out exceeds the maximal value, change the shaft
hub.29. Assemble left front brake assembly [64000134]
30. Assemble left front brake branch pump assemblyUse two bolts to assemble brake branch pump assembly on
steering knuckle.
Torque: 106
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m31. Assemble speed sensor assembly of left front wheel
[67000020](a) Assemble wiring harness of speed sensor and brake hose
on the absorber with bolts.
Torque: 29 N
⋅ ⋅⋅ ⋅
⋅m
(b) Use the bolts to assemble speed sensor to steering knuckle.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
Note: Do not damage the speed sensor.zPrevent it from contacting with sundries.zWhen assembling the sensor, wiring harness of sen-
sor could not bend.32. Assemble fixing nut of left front drive shaft
[64000083](a) Assemble new fixing nuts,
Torque: 216
± ±± ±
± 15 N
⋅ ⋅⋅ ⋅
⋅m
(b) Use chisel and hammer to make fixing nut concave and fix
them.33. Assemble front wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m34. Check and adjust wheel alignment (referring to page
87).
35. Check the ABS speed sensor signal.
127